• 대한조선학회논문집
• /
• 제40권3호
• /
• pp.22-28
• /
• 2003

In rough seas, bow-flare regions of the full ships (tanker and bulk carrier) are subiect to high impact pressures due to the on-coming breaking waves. And many ships suffer structural damages in that region, even though they were built under the bow structure strengthening rules of the ship classes. So, a new design method for bow-flare structure is highly required. In this paper, a new prediction method of the bow-flare impact pressure (in terms of equivalent static pressure) acting on the full ships' bow is presented. This method is based on the 6 full ships' damage analysis and the breaking wave impact mechanism. Calculation results of the bow-flare impact pressure and the shell plate thickness are shown and discussed. Through the example calculations, it was found that the present method is useful for the structure design of the full ships' bow.

• 한국해양공학회지
• /
• 제17권5호
• /
• pp.39-47
• /
• 2003

A study of the structural strength evaluation on the doubler plate, considering various load cases that were subjected to in-plane and out of plane combined load, has been performed through the systematic evaluation process. In order to estimate the proper static strength of doubler plate for various load cases, elasto-plastic large deflection analysis is introduced, including the contact effect between main plate and doubler. The characteristics of stiffness and strength variation are discussed, based on the results. In order to compare the doubler structure with the original strength of main plate, without doubler, simple formulas for the evaluation of the equivalent flat plate thickness are derived for each load case, respectively, based on the additional series of analysis of flat plate structure. Using these derived equations, the thickness change of an equivalent flat plate is analyzed according to the variation of various design parameters of doubler platesome design guides are suggested in order to maintain the original strength of main plate without doubler reinforcement. Finally, correlation between derived equivalent flat plate formula and the developed buckling strength formulas are discovered, and these relations are formulated for the future development of simple strength evaluation formula of general doubler plate structure.

• 대한기계학회논문집A
• /
• 제33권6호
• /
• pp.568-572
• /
• 2009

We present a ternary microfluidic multiplexer unit, capable to address three flow channels using a pair of control lines with two different threshold pressure valves. The previous binary multiplexer unit addresses only two flow channels using a pair of control line with identical threshold pressure valves, thus addressing $2^{n/2}$ flow channels using n control lines. The present ternary multiplexer addressing three flow channels using a pair of control lines, however, is capable to address $3^{n/2}$ flow channels using n control lines with two different threshold pressure valves. In the experimental study, we characterized the threshold pressure and the response time of the valves used in the ternary multiplexer. From the experimental observation, we also verified that the present ternary multiplexer unit could be operated by two equivalent valve operating conditions: the different static pressures and dynamic pressures at different duty ratio. And then, $3{\times}3$ well array stacking ternary multiplexers in serial is addressed in cross and plus patterns, thus demonstrating the individual flow channel addressing capability of the ternary multiplexer. Thus, the present ternary multiplexer reduces the number of control lines for addressing flow channels, achieving the high well control efficiency required for simple and compact microfluidic systems.

• 대한조선학회논문집
• /
• 제40권3호
• /
• pp.29-36
• /
• 2003

In rough seas, bow-flare regions of the fine ships (container ship and PCC) are subject to high impact pressures due to the bow-flare slamming. And many ships suffer structural damages in that region, even though they were built under the bow structure strengthening rules of the ship classes. So, a new design method for bow-flare structure is highly required. In this paper, a new prediction method of the bow-flare impact pressure (in terms of equivalent static pressure) acting on the fine ships' bow is presented. This method is based on the 11 fine ships' damage analysis and the mechanisms of water entry impact and breaking wave impact. Calculation results of the bow-flare impact pressure and the shell plate thickness are shown and discussed. Through the example calculations, it was found that the present method is useful for the structure design of the fine ships' bow.

• Wind and Structures
• /
• 제30권6호
• /
• pp.559-573
• /
• 2020

This paper presents a study on the effectiveness of the proper orthogonal decomposition (POD) technique for reconstruction of wind pressure field as applied to a cylindrical shell roof based on simultaneously measured wind pressure data. The influence of wind loading mode truncation on the statistics of dynamic pressures and wind load effects are investigated. The results showed that truncation of higher wind loading modes can have more noticeable influence on the maximum and minimum pressures that the standard derivation (STD) values. The truncation primarily affects the high-frequency content of the pressures. Estimation of background response using wind loading modes is more effective than the use of traditional structural modal analysis.

• 대한조선학회지
• /
• 제15권3호
• /
• pp.1-7
• /
• 1978

The dynamic pressures on the bottom of high speed small crafts are studied. Using the dynamic load factor the dynamic pressure can be replaced by equivalent static pressure. Assuming that (1) the system is undamped with a single degree of freedom and (2) the load is applied triangularly, we obtained the max, value of the dynamic load factor of 1.455. We believe that this method could provide a guide to the designer who has no data on the craft in the preliminary structural design stage.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 추계학술대회 논문집
• /
• pp.285-290
• /
• 2005

Micro On-Off valves are currently recognized as the core technology in the fields of the micro fluid chip fur medical applications and production lines of semi-conduct chip. Micro valves that operate by compressed air need the high-speed responsibility, repeatability, the absorbability and the uniform pressure by the poppet. In this study, Micro On-Off valves that posses the high-speed responsibility and the high rate of flow have designed and analyzed through the law of equivalent magnetic circuit and Finite Element Method (FEM) respectively. In case of poppet, Flow field characteristic was analyzed by the variation of poppet and it was able to display flow field by changing the location of the poppet. Also, we verified possibility of the design through the static and dynamic pressure and the 3D distribution curve of the force by working the front poppet.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2005년도 제24회 춘계학술대회논문집
• /
• pp.99-105
• /
• 2005

초고온($2700^{\circ}C$) 연소가스에 직접 노출된 상태에서 가스유동에 의한 동압을 받는 추력편향장치용 제트 베인의 열구조 안전성을 평가하기 위하여 내열합금의 초고온 인장시험 및 3차원 비선형 수치해석을 수행하였다. 고온 구조거동을 분석하여 제트 베인의 구조안전성을 평가하였으며 구조해석결과를 지상연소시험결과와 비교하였다. 구조 및 열 하중의 대부분은 제트 베인 축에 집중되었으며, 축은 $1400^{\circ}C$ 이하에서 구조적으로 안전한 것으로 밝혀졌다. 지상연소시험결과와 구조해석결과의 비교를 통하여 베인 하중과 축의 변위를 기준으로 구조안전계수를 평가하는 것이 등가응력에 의한 평가 기준보다 더 유용한 기준으로 판단되었다.

• 한국추진공학회지
• /
• 제9권3호
• /
• pp.18-24
• /
• 2005

초고온(2700$^{\circ}C$ ) 연소가스에 직접 노출된 상태에서 가스유동에 의한 동압을 받는 추력편향장치용 제트 베인의 열구조 안전성을 평가하기 위하여 내열합금의 초고온 인장시험 및 3차원 비선형 수치해석을 수행하였다. 고온 구조거동을 분석하여 제트 베인의 구조안전성을 평가하였으며 구조해석결과를 지상 연소시험결과와 비교하였다. 구조 및 열 하중의 대부분은 제트 베인 축에 집중되었으며, 축은 1400$^{\circ}C$ 이하에서 구조적으로 안전한 것으로 밝혀졌다. 지상연소시험결과와 구조해석결과의 비교를 통하여 베인 하중과 축의 변위를 기준으로 구조안전계수를 평가하는 것이 등가응력에 의한 평가기준보다 더 유용한 기준으로 판단되었다.

• 유공압시스템학회논문집
• /
• 제3권4호
• /
• pp.14-20
• /
• 2006

Recently, the on-off solenoid valves have been focused on core technology in the fields of the production line of semi-conductor chips and the micro fluid chips for bio-medical applications. A key characteristics for on-off solenoid valve, operated by compressed air, are high speed response and great repeatability. Indeed, it is also important to keep the pressure on the cross-sectional area of the poppet to be constant regardless of the fluctuation of the pressure exerted on the ports. In this study, we have designed and analysed the high-speed and high flow rate on-off solenoid valve using the analogy of equivalent magnetic circuit and Finite Element Method (FEM) respectively. In case of poppet, flow field characteristics was analyzed by the variation of poppet and it was able to display flow field by changing the location of the poppet. Also, we verified possibility of the design through the static and dynamic pressure and the 3D simulation using distribution curve of the force by working the front poppet.