• Proceedings of the KSME Conference
• /
• 2002.08a
• /
• pp.775-778
• /
• 2002

In order to analyse the mechanism of a flow tone around a cavity, the correlations between the flow in the cavity and the boundary layer flow in front of the cavity are studied experimentally in this paper. The instability In the boundary layer forms the vortex at the front edge of the cavity and the flow tone is occurred by the vortex breakdown at the rear edge of the cavity Therefore, the boundary layer measurement is important in the cavity flow control. We measure the velocity of the boundary layer at the entrance of the cavity using hot-wire anemometry and the flow tone around the cavity by microphone. The boundary layer characteristic is changed by the various angle of the flap on the front edge of the cavity, while it is less influenced by the ratio of length and depth of the cavity.

• Journal of Energy Engineering
• /
• v.7 no.1
• /
• pp.122-130
• /
• 1998

A simplified heat transfer model for the cooling capability of the AP 600 PCCS is proposed I this paper. As the PCCS domain is covered with very thin and long water film, it is phenomenologically divided into 3 regions; water entrance effect region, asymptotic region, and air entrance effect region. As the length of the asymptotic region is estimated to be over 90% of the whole domain, the phenomena in the asymptotic region is focused. Using the analogy between heat and mass transfer phenomena in a turbulent situation, a new dependent variable combining temperature and vapor mass fraction was defined. The similarity between the PCCs phenomena in the asymptotic region and the buoyant air flow phenomena on a vertical heated plate is derived. Using the similarity, the simplified heat transfer correlations for the interfacial heat fluxes and the ratios of latent heat transfer to sensible heat transfer were established. To verify the accuracy of the correlation, the results of this study were compared with those of other numerical analyses performed for the same configuration and they are well within the range of 15% difference.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1998.03a
• /
• pp.210-213
• /
• 1998

A kinematically admissible velocity field is developed for the analysis of twisting of extruded products. The twisting of extruded product is caused by the linearly increased rotational velocity from the center on the cross-section of the workpiece at the die exit. In the analysis, the rotational velocity in angular direction is assumed by the multiplication of radial distance and angular velocity. The angular velocity is zero at the die entrance and is increased linearly by axial distance from die entrance. The increase rate of angular velocity is determined by the minimization of plastic work. The results of the analysis show that the angular velocity of the extruded product increase with the die twisting angle and the aspect ratio of product and friction condition and reduction area and show that angular velocity increases with the decreases in die length.

• Transactions of Materials Processing
• /
• v.8 no.2
• /
• pp.143-151
• /
• 1999

The twisting and extrusion process of the product with trapezoidal helical fin from the round billet is developed by the upper bound analysis. The twisting of extruded product is caused by the twisted die surface connecting the die entrance section and the die exit section linearly. In the analysis, the rotational velocity in angular direction is assumed by the multiplication of radial distance and angular velocity. The angular velocity is increased linearly by axial distance from the die entrance. The increase rate of angular velocity is determined by the minimization of plastic work. The results of the analysis show that the angular velocity of the extruded product increases with the die twisting angle, the reduction of area, and decreases with the die length, the friction condition.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.30 no.1
• /
• pp.52-60
• /
• 2002

This paper presents a streetscape design for "Dangiae-Gil"which is located at 126-1 Yangpyung-2dong, Yeongdeungpo-gu, Seoul and is about 500m in length and about 24m in width. The design goals are to make a green street on which people want to walk and people can walk and rest safely and pleasantly. To achieve these goals, concepts of environmentally-friendliness, placeness, safety, amenity, vitality, connectivity, and democracy are developed. For pedestrian safety, shared street concepts, such as crank, slalom etc. are adopted. The site is divided into 5 thematic spaces, such as "Village Entrance Space", "Culture Street", "Dangsan Park", "Nature Street", and "Ferry Space". The Village Entrance Space, which is an entrance of the Dangjae-Gil and a welcoming space, is for communicating information about the area. "Dangnamu"(zelkova tree) and signs are introduced here. The Culture Street is for experiencing past and present culture of the area. Colored tiles and plant boxes attached to benches are introduced. The Dangsan park is a sacred space where modem people can feel the sacredness of nature arid of being in a refuge. Dangjib, Dangnamu, multi-purpose plaza, athletic facilities, and playground for infants are introduced. The Nature Street is a space for feeling and teaming nature which has disappeared from the area leading to the river and a space for community participation. The elementary school walls were demolished and nature education spaces, such as butterfly and dragonfly garden, ecological pond, wildflower garden, etc., which are related to school education, are introduced. The Ferry Space is a space symbolizing a old ferry crossing and an entrance plaza to a bridge for "Sunyu-do\" . A boat-shaped deck, an elevator for handicap people, and parking space are introduced. In conclusion, sustainable management schemes for the site are suggested.sted.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.44 no.4
• /
• pp.273-281
• /
• 2008

In this study, the effect of slope length and angle at the entrance to fishing pots on the size of captured shrimp was examined to determine the optimal design of pots for use in Hokkaido, Japan. The purpose of the current study was to optimize the design of shrimp pots to allow greater control over the size of captured individuals for the purposes of shrimp resource management. Tank experiments were conducted to determine the optimal slope length and slope angle by analyzing the sizes of shrimp entering 10 model pots with combinations of five different slope lengths on slope angle of current shrimp pot, and five different angles on slope length of current shrimp pot. The results showed that, as the slope length of the pot increased, the size of individuals which entered the pot increased. In addition, as the slope angle was elevated in each of the five different slope angle treatments, the size of individuals entering was also increased.

• International Journal of Highway Engineering
• /
• v.14 no.3
• /
• pp.173-182
• /
• 2012

Entry and exits of the rest area are sections where designed speed can be rapidly change and also a weak traffic safety section. In addition, two tasks can be performed simultaneously at entry of the rest area, particularly searching for deceleration and parking spaces/parking sides etc. Thus, design criteria is required in order to procure the stability of accessed vehicle. In case of Korea, geometric structure design criteria of entry facilities, such as toll-gate, interchange, junction etc was established. However there are no presence in a detailed standards for geometric structure of the rest area which affiliated road facilities. In this study, Derive problems in regards to the entry of geometric structure of resting areas by utilizing a sight survey and an investigation research of traffic accidents. The survey was targeting 135 general service areas. After Classifying the design section of resting areas' entry as well as derive design elements on each section, a speed measurement by targeting entry of rest areas and car behavior surveys were performed, then each element's minimum standard was derived through the analyses. According to the speeds at the starting/end point of entrance connector road, the minimum length of the entrance connector road is decided as 40m using Slowing-down length formula and based on the driving pattern, the range of the junction setting angle of the entrance connector road is defined as $12^{\circ}{\sim}17^{\circ}$. Suggest improvement plans for existing rest areas that can be applied realistically. This should be corresponded to the standards of entry and exit of developed rest areas.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.13 no.5
• /
• pp.1032-1043
• /
• 1989

The heat transfer characteristics of the drag reducing polymer solutions are investigated experimentally in the thermal entrance region of circular tube flows. Fluids used in experiments are the aqueous solutions of high molecular polymer, polyacrylamide Separan AP-273 and the range of polymer concentrations is from 20 to 1000 wppm. Two stainless steel tubes with inside diameter 8.5mm(L/D=712) and 10.3mm(L/D=1160) are used for the heat transfer flow loops. The flow loop is set up to measure friction factors and heat transfer coefficients of test sections in two different modes; the recirculating flow system and once-through flow system. The test tubes are heated directly by electricity to apply the constant heat flux boundary conditions to the wall. Three different types of adaptors are used to observe the effects of the upstream flow conditions of the heat transfer test sections. The viscosity and characteristic relaxation time of the test fluids circulating in the flow system are measured by the capillary tube viscometer and falling ball viscometer at regular time intervals. The installed adaptors exhibit slight effect on the entrance heat transfer of Newtonian fluid. However, no noticeable effects are observed for the entrance heat transfer of the drag reducing fluids. The order of magnitude of the thermal entrance lengths of the drag reducing fluids which follow the minimum friction asymptote is much longer than that of Newtonian fluids in turbulent flows. A new dimensionless parameter, the viscoelastic Graetz number, is defined and all the experimental data are recasted in terms of the viscoelastic Graetz number. The local Nusselt number of the viscoelastic fluids is represented as a function of flow behavior index n and the viscoelastic Graetz number. As degradation continues the viscosity and the characteristic relaxation time of the testing fluids decrease. Weissenberg number defined by the relaxation time and D/V appears to be a proper dimensionless parameter in describing degradation effects on heat transfer of the viscoelastic fluids.

• Journal of Energy Engineering
• /
• v.21 no.1
• /
• pp.18-25
• /
• 2012

This work investigated the influence of the chimney dimensions(exit and entrance length, and diameter) on the heat transfer of a vertical cylinder in a duct. The measured mass transfer rates for the natural convection of vertical cylinder in a duct were presented for Prandlt number 2,094, Rayleigh number in the range of $4.55{\times}10^9$, $5.79{\times}10^{10}$, and $1.69{\times}10^{11}$. Experiments were performed using a copper sulfate electroplating system to simulate heat transfer based upon the analogy concept. The diameter of the duct was varied from 0.06 m to 0.14 m, and the heights from 0.30 m to 1.10 m. Nusselt numbers measured at open channel condition agreed well with the existing laminar heat transfer correlations for vertical plate developed by Le Fevre. The increase of the exit length enhanced the heat transfer up to a certain duct height but further increase does not affects the heat transfer. The heat transfer decreased with increasing the entrance length up to a certain duct height and was constant at further increase. The Nusselt number decreased with increasing the diameter of duct, until Nusselt number becomes similar to that at open channel beyond a certain diameter.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2002.04a
• /
• pp.643-648
• /
• 2002

In the cutting of plate steel, the quality of the cut surfaces is strongly dependent on the cutting conditions such as cutting speed, kerf width, plate thickness, length of tip-specimen and oxygen pressure etc. the cutting tests of plate steel were carried out using CNC gas cutting machine. this paper deals with cutting characteristics of plate steel using CNC cutting machine. the width of cutting entrance and exit, the surface roughness of cutting surfaces and the cutting surface are examined at various cutting conditions.