• 한국정밀공학회지
• /
• 제28권8호
• /
• pp.894-903
• /
• 2011

In this paper, the capability index is introduced in order to improve the reliability of new concept machine tools and the method to improve the machine accuracy from the analysis of cutting process, statistical methodology and influence factors are proposed. In addition, the rib structure of bed and column in machine tools is analyzed by using the thermal impact method in order to analogize the rib pattern which has the small thermal deformation under thermal boundary condition. In the analysis of column rib structure, thermal boundary condition is separated to heat conduction and heat transfer to appropriate real boundary condition. Finally, performance chart of bed and column rib structure is provided for designer to estimate each rib pattern and select rib structure appropriating to thermal condition.

• 한국정밀공학회지
• /
• 제22권11호
• /
• pp.151-158
• /
• 2005

Micro-machine tool is essential in the micro/meso cutting for the sake of saving of space, resources, and energy. In this research, a micro-turning lathe was fabricated with piezoelectric feed drive mechanism, and motion of each axis was generated by stepwise mechanism with two piezo actuators. The resolution to drive the axis was $0.05{\mu}m$ and position accuracy less than $2{\mu}m$ was assured. From the positioning experiment, piezo feed mechanism is good enough for the micro machine tools. Many fuming experiments were carried out with diamond-cutting tools to evaluate cutting capability of a machine tool. Continuous flow type chip could be obtained even if the cutting speed was very low due to small diameter of workpiece. However, thorough investigation about machineability in micro/meso cutting is inevitable to assure high quality surface roughness in micro machine tool.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1996년도 추계학술대회 논문집
• /
• pp.621-625
• /
• 1996

The feed system of the machine tools is limited by the mechanical transmission elements. However, thanks to the advanced modern technology, those machines are able to equip with linear motors. In this paper, the types and application aspects of linear motor are discussed and a synchronous type of the linear motors has been applied to X-Y table for machining center. The performance shows an outstanding result in terms of the accuracy, speed and stiffness. Machine tool system with linear motors is expected to be more productive machines using linear motor in the near next years.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1996년도 추계학술대회 논문집
• /
• pp.26-30
• /
• 1996

This paper presents the performance of CBN tools in the machining of hardened die-materials, SKD11 and SKD61 steel with HRC 50, by high-speed face milling. Generally, grinding or EDM is being used in machining of hardened materials but the cost is very high. If those can be replaced by cutting, it will be a greatly economical advantage. CBN tool has been recognized as an effective tool in turning, but it has not been in milling. So wear and surface roughness mode of CBN tool for hardened SKD11 and SKD61 steel were investigated by high-speed face milling in this study Also the relation between cutting force and wear mode of CBN tools was investigated.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1996년도 추계학술대회 논문집
• /
• pp.212-216
• /
• 1996

Recently, with the development of NC and CNC machine tools and the high labor wage, the cutting process requires the high speed and automatic system which uses industrial robots and the flexible manufacturing system(FMS) that combines several machine tools. In this system, the whole system can be influenced by just one of the machin tools. So it needs to detect a problem and to solve it immediately In in-process state. The monitoring system through measuring the motor current with current sensor has been attracting the attention of lots of researchers view of its low cost and flexibility. By using the pattern discriminant with the detected three-phase-current signal, that is, $I_{RMS}$, a system which can monitor and analyze abnormal machining process condition of the workpiece during the machining will be able to be developed in this research.h.

• 한국정밀공학회지
• /
• 제16권10호
• /
• pp.217-224
• /
• 1999

Trouble shooting of modern machine tools equipped with sophisticated electronic as well as mechanical parts is so difficult that it is usually depends upon the experience and accumulated knowledge of the diagnosing persons. On the other hand, tool users are scattered in wide area, which makes it expensive for a machine tool maker to run a vast service network. An unmanned diagnosis system to which users can have access at all times could be an efficient alternative. For this purpose, a rule-based expert system for diagnosing machine tools is developed. This paper describes the structure of diagnostic knowledge, the rule firing mechanism, the diagnosis flow, and user query process. An example shows the feasibility of problem solving on site without help of a service expert from machine tool maker.

• 한국정밀공학회지
• /
• 제28권4호
• /
• pp.505-512
• /
• 2011

Linear permanent magnet synchronous motors utilize high-energy product permanent magnet to produce high thrust, velocity and acceleration. Such motors are finding applications requiring high positioning accuracy and speed response, for example, machine tools, in the absence of mechanical gears and ball screw systems. A disadvantage of the linear motors is high power loss in comparison with rotary motors. For the application of the linear motors to machine tools, it is required to use water coolers and to improve the thermal behavior through insulation and structure optimization or control strategies. This paper presents the function of the secondary part of the linear synchronous motor as to the thermal behavior and the improving method. The result shows cooling pipe combined with an insulation layer is a suitable design for improving of the thermal behavior.

• 한국CDE학회논문집
• /
• 제3권3호
• /
• pp.177-182
• /
• 1998

The computer related techniques have been developed rapidly in the field of metal removal industry. The electronic catalog for mechanical elements is one of such developments realized in recent years. As the emergence of the electronic catalogs in the 90s, it breaks the restriction of the traditional catalog and becomes a helpful and efficient tool in the field. In this paper, we develop an electronic catalog for the cutting tools of the Korea Tungsten Co. Ltd. The catalog consists of three parts: a preprocessor for tool selection, a database for tool, and a postprocessor for search result. A preprocessor for tool selection is developed under a user-friendly consideration. A database for tool consists of milling, drilling, and reaming tools with a list of cutters, inserts, and components. A postprocessor for search result consists of weight, dimension. drawing, product order number etc. of the tools. It also suggests the optimized cutting condition of the selected tool using a neural network technique which is done by an independent research group.

• 항공우주시스템공학회지
• /
• 제3권3호
• /
• pp.7-12
• /
• 2009

Reduction of the aerodynamic drag is one of the most hot issues of car industries. Many researchers have studied in the area of drag reduction methodology using experimental tools or numerical tools. In general, car shape design is the main focus to reduce the drag in aerodynamic research area. However, not many people have studied the aerodynamic interference between running cars to figure out the drag variation. In this research, the aerodynamic interference between two running cars have been analyzed by using numerical tools, FLUENT 6.2. Several different models of cars and two different distances between two running cars are considered.

• 한국정밀공학회지
• /
• 제20권10호
• /
• pp.74-81
• /
• 2003

This paper describes that the micro-cutting of WC-Co using PCD (Polycrystalline Diamond) and PcBN (Polycrystalline Cubic Boron Nitride) cutting tools are performed with SEM(Scanning Electron Microscope) direct observation method. The purpose of this study is to present reasonable cutting conditions to obtain precise finished surface and machining efficiency. Summary of the results are shown below: (1) The thrust cutting forces tend to increase more than the principal forces as the depth of cut and the cuttlllg speed are increased preferably on orthogonal microcutting. (2) The tool wear in the flank face was formed larger than that in the rake face on orthogonal micro cutting. (3) The wear appearance for PCD tools is abraded by hard WC particles of the work materials, which lead diamond grain to be detached from the bond.