• 한국자동차공학회논문집
• /
• 제2권3호
• /
• pp.94-104
• /
• 1994

In order to improve engine performance and its reliability it is very important to find the friction force between piston-ring assembly and cylinder wall in engine operating conditions. A new system was developed for the piston-ring assembly friction force measurement. This system had a relatively high fundamental frequency at 884 Hz and a fine resolution of 0.5N in friction force measurement. Comparing with existing floating liner systems this systems required small installation space and at the same time alleviated the system noise problem induced by the thrust and slap impulse forces.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1998년도 제27회 춘계학술대회
• /
• pp.115-123
• /
• 1998

A $Si_3N_4$ tappet shim was devdoped in a direct OHC engine for the friction reduction of valve train system that contributes significantly to the engine friction in real driving condition. For commercializing $Si_3N_4$ tappet shim, it is important to reduce the machining cost. Therefore we analytically and experimentally figure out the optimum condition. Using ceramic tappet shims machined with different surface roughness, the effects of roughness on the friction loss were analyzed in view of the lubrication behavior. From this results it is shown that the friction torque of valve train system quickly drops at a certain surface roughness of ceramic tappet shim and its value remains constant despite further smoothing.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1998년도 제28회 추계학술대회
• /
• pp.75-81
• /
• 1998

It is very important to evaluate the friction force of valve train system in the aspect of reducing friction loss of engine. To this end, we have developed measuring system of friction force of engine valve train system. There were two major factors in the process of development of it. One was it had to accurately measure the friction force up to 3500 Crpm without any problems such as mechanical vibration, electrical noise and so on. The other was it also had to simulate real engine conditions such as Crpm, oil temperature, oil pressure and oil aeration including effect of belt drive system. In this paper we have introduced the process of development of it based on test results, and also analysis process of measured data.

• 대한기계학회논문집B
• /
• 제38권12호
• /
• pp.1035-1042
• /
• 2014

엔진 마찰 저감은 엔진 개발의 중요한 항목이 되어왔다. 엔진의 기계적 마찰 손실 중 피스톤계의 마찰이 40~55%에 해당하고, 피스톤 부분의 마찰을 제거할 수 있다면 투입되는 전체 에너지의 5% 정도 향상시킬 수 있다. 엔진의 마찰 손실을 감소시키기 위해서 각 요소에서의 마찰 수준, 이에 영향을 미치는 인자에 대한 분석 및 다른 엔진들과의 비교분석이 필요하다. 하지만 기존 연구에서 마찰이 발생하는 윤활막의 연구들이 유체역학 바탕의 모델링에서 수행해 왔으나, 피스톤계의 윤활막이 크게는 마이크로에서 작게는 나노단위의 영역에 해당하므로 분자들간의 상호관계를 고려할 필요가 있다. 따라서, 본 연구에서는 엔진 실린더 라이너를 따라 형성하는 유막의 운동을 미시적으로 접근하여 분자들간의 상호작용에 따른 마찰변화를 제시하고자 한다.

• 항공우주시스템공학회지
• /
• 제17권5호
• /
• pp.11-18
• /
• 2023

The architecture of the Fuel Thermal Management System (FTMS) in a commercial aircraft engine was built to model and simulate the fuel system. The study shows the thermal interactions between the fuel and engine lubrication oil through the mission profile of a high bypass ratio, two-spool turbofan engine. Fuel temperature was monitored as it flowed through each sub-component of the fuel system during the mission. The heat load in the fuel system strongly depended on the fuel flow rate, and was significantly increased for the periods of cruise and descent with decrease of fuel flow rate, rather than for the periods of take-off. Due to the thermal interaction in the pump housing, the fuel temperature at the outlet of the low-pressure pump was increased (4.0, 9.2, and 30.0) % over the case without thermal interaction for take-off, cruise, and descent, respectively.

• Journal of Advanced Marine Engineering and Technology
• /
• 제38권10호
• /
• pp.1251-1256
• /
• 2014

The use of lubrication oil is of many purposes and one among them is to drive the engine mounted on a ship. Hence the supply of clean lubrication oil is important. And an oil purifier is one of key components in marine diesel engines. At present, the element type full-flow oil filter has been widely used for cleaning the engine oil. The self-driven centrifugal oil purifier is a device which is used to remove the impurities in lubrication oil using a jet flow. The flow characteristics and the physical behaviors of particles in this self-driven oil purifier were investigated numerically and the filtration efficiencies were evaluated. For calculations, a Computational Fluid Dynamics method is used and the Shear Stress Transport turbulence model has been adopted. The Multi Frames of Reference method is used to consider the rotating effect of the flows. The influence of centrifugal forcehas been numerically investigatedto improve filtration efficiency of tiny particles. As a result of this research, it was found that the particle filtration efficiency using the only center axis rotating and outer wall rotating system are higher than that of the fully rotating system in the self-driven oil purifier.

• 한국자동차공학회논문집
• /
• 제22권2호
• /
• pp.123-133
• /
• 2014

Minimizing the cylinder wear and the consumption rate of cylinder oil in a large two-stroke diesel engine is of great economic importance. A motor-driven cylinder lubricator for Sulzer RT-flex large two-stroke diesel engines developed by authors is in need of improving the lubricating system to lubricate cylinder parts optimally by an electronically controlled quill device according to changes of engine load and revolution speed. In order to apply the developed accumulating distributor to an integrated cylinder lubricator by the electronically controlled system as the third research stage, the lubricating system is improved in the electronically controlled quill device with a solenoid valve. In this study, the effects of lubricator revolution speed, driving pressure(or plunger stroke) and cylinder back pressure on oil feed rate and lubrication inequality rate are investigated by using the integrated cylinder lubricator system with an accumulated distribution by the electronic control(I.C.S.), and the oil feed rate and lubrication inequality rate of I.C.S. are compared with those of the motor-driven cylinder lubricator by the electronically controlled quill system equipped with an accumulating distributor(E.D.S.). It is found that the oil feed rate of I.C.S. is smaller than that of E.D.S. due to the reduction of delivery velocity by the higher delivery pressure, and the variances of lubrication inequality rate for I.C.S. have become smaller than those of E.D.S. as the driving pressure in all experimental conditions increases, except for the driving pressure of 26 bar(plunger stroke 2 mm) at the cylinder lubricator speed of 120 rpm.

• Tribology and Lubricants
• /
• 제11권1호
• /
• pp.44-49
• /
• 1995

Friction characteristic of an engine crankshaft bearing is affected by revolution speed, applied loads, and viscosity of lubrication. So, experimental investigation is required to observe the friction characteristics using these factors. Hydraulic cylinder, servo controller system which can be modified the applied load, and test rig for the observation of the characteristics of engine crankshaft bearings were designed and fabricated, and some experiments were performed. Friction torque, journal locus and circumferential temperature variation of crankshaft bearing were measured according to applied load, revolution speed, and oil inlet temperature.

• 한국군사과학기술학회지
• /
• 제8권1호
• /
• pp.49-55
• /
• 2005

Due to small and light mission payloads, subsystems and propulsion system, small sized UAVs come to be available for reconnaissance that have been performed by aircraft and huge UAVs. The objective of this study is to develop an efficient propulsion system for small reconnaissance UAVs. A glow engine was modified for an efficient and robust 4-stroke gasoline engine with carburetor, new electronic control unit and lubrication system. Engine modification technique and small engine performance test stand are capable of economical method for military UAVs.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1998년도 제28회 추계학술대회
• /
• pp.151-159
• /
• 1998

디젤 엔진의 푸쉬로드 타입의 밸브 트레인에서의 힘의 전달 과정을 기구학적 응용을 통하여 구하였다. 이러한 힘의 최종 전달 단계인 캠과 평판 종동물의 접촉에서의 작용하중과 상대 운동 속도를 계산하였고 접촉면에서의 유막 두께를 고체면의 탄성변형을 고려하여 계산하였다. 특히 탄성 유체 윤활의 해석을 하는데 있어서 안정성과 수렴성이 우수한 멀티그리드 멀티레벨 기법을 사용하였으며 동하중 상태를 고려하여 유막 두께를 계산하고 기존의 정상상태의 해석해와 비교하였다.