• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2000.11a
• /
• pp.182-186
• /
• 2000

The porous woven hose is recently considered as an effective element of automotive intake systems. In order to predict the acoustic performance of an intake system with a porous woven hose, the information on the acoustic wall impedance is required. In this article, a measurement technique that is valid over the low frequency range and without mean flow condition is presented. The measurement is performed in a cylindrical chamber with a concentric layout of the sample and the resistance is estimated from measured reactance and transmission loss data. It is observed that the measured transmission loss for a porous woven hose with an arbitrary length agrees well with the predicted one that uses the estimated impedance for a small sample length.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.11 no.6
• /
• pp.963-970
• /
• 1987

It has been a long time that black smoke emitted from buses and trucks powered with diesel engines, especially city-buses, came to be a serious air pollution problems in large cities as Seoul and Pusan. Therefore, proper means to reduce black smoke from diesel engines have to be considered as soon as possible, because it will take quite a long time to replace major passenger transportation system in cites from city-buses to subway. This paper, as a study on the reduction of diesel black smoke, showes how the black smoke of diesel engines can be reduced at various loads and engine speed by supplying small amount of gaseous fuel as LPG into the intake manifold. Thermal efficiency has been also considered for users, and confirmed through the engine test.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.3 no.1
• /
• pp.118-130
• /
• 1995

Fuel spray in a gasoline engine is a significant factor for the decision of engine power, pollutant emission and the design of intake manifold system. Three kinds of fuel which has other physical properties are chosen in this study, and it is observed using an image processing method that the mechanism and structure of free fuel spray with a throttle type gasoline injector, and the detailed characteristics of droplet size and velocity distributions are obtained by macro and micro-scopic measuring method respectively. It is verified that the initial breakup behaviors are depended on We like the result of Reitz's study, and also observed that the spray of octane and solvent with Re of 210~330 and 270~330 respectively are better than ethanol which has relatively high density and viscosity.

• Journal of Mechanical Science and Technology
• /
• v.16 no.10
• /
• pp.1314-1319
• /
• 2002

A mathematical model and control laws for an Electronic-Vacuum Booster (EVB) for application to vehicle cruise control will be presented. Also this paper includes performance test result of EVB and vehicle cruise control experiments. The pressure difference between the vacuum chamber and the apply chamber is controlled by a PWM-solenoid-valve. Since the pressure at the vacuum chamber is identical to that of the engine intake manifold, the output of the electronic-vacuum booster Is sensitive to engine speed. The performance characteristics of the electronic-vacuum booster have been investigated via computer simulations and vehicle tests. The mathematical model of the electronic-vacuum booster developed in this study and a two-state dynamic engine model have been used in the simulations. It has been shown by simulations and vehicle tests that the EVB-cruise control system can provide a vehicle with good distance control performance in both high speed and low speed stop and go driving situations.

• Journal of the korean Society of Automotive Engineers
• /
• v.10 no.4
• /
• pp.39-56
• /
• 1988

In this study, the computer program was developed to predict the engine performances and exhaust emissions of a 4-cylinder 4-stroke cycle ignition engine including intake and exhaust system. The simulation models applied to each process were as follows. For the combustion process, two zone model which requires only one empirical constant was applied, and for the gas exchange process, the method of characteristics that allows the calculations of the time variation and spatial variation of properties along the pipes was used. Constant pressure perfect mixing model was applied to take into account of the interaction at manifold branches. To predict exhaust emissions, twelve chemical species were considered to be present in combustion products. These species were calculated through equilibrium thermodynamics and kinetic theory. The empirical constants reduced to least number as possible were determined through the comparison with the experimental indicator diagram of one particular operating condition and these constants were applied to other operating conditions. The predicted performances and emissions were compared with the experimental results over the wide range of operating conditions.

• Proceedings of the KSME Conference
• /
• 2008.11b
• /
• pp.3032-3037
• /
• 2008

Variable Valve Timing (VVT) system can be used to improve fuel economy, performance and emissions. This study is identified the effect of VVT in terms of wide open throttle torque, Residual gas fraction, volume efficiency. Engine cycle simulations are performed on 2.0L DOHC in-line 4-cylinder SI engine by using WAVE of Ricardo. Results of the simulations had good agreement with WOT torque experimental data, and helped to predict the tendency of performance as the valve timings change. WOT torque was higher when intake valves were closed early for low rpm and late for high rpm.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.11 no.5
• /
• pp.15-21
• /
• 2003

The liquid phase LPG injection engine is a new technology to make good use of LPG as a clean energy. However, it is difficult to precisely control air/fuel ratio in the system because of variation of fuel composition, change of temperature and flash boiling injection mechanism. This study newly suggests an injector control logic for liquid phase LPG injection systems. This logic compensates a number of effects such as variations of density, stoichiometric air/fuel ratio, injection delay time, injection pressure, release pressure which is formed by flash boiling of fuel at nozzle exit. This logic can precisely control air/fuel ratio with only two parameters of intake air flow rate and injection pressure without considering fuel composition, fuel temperature.

• Journal of Advanced Marine Engineering and Technology
• /
• v.33 no.8
• /
• pp.1100-1106
• /
• 2009

Recently, there are quite a lot of attention is drown on the researches related to of Miller method applied high expansion cycle. For this study, high expansion cycles are formed and analyzed with the base view point of thermodynamics, and the features of each factors are also investigated. As a result of analysis, the expansion-compression ratio is expected with a decrease of effective compression ratio as intake valve closing time retarded, however, the decrease of mean effective pressure and its output is accompanied with the counterflow of intake air. Accordingly, as the consequence of such failure, it is expected that an alternative is needed for the realization of high expansion cycles, and the improvement over thermal efficiency. To materialize such cycle, the control system to delay the closing time of intake valve was designed and VVT, the 3 S/B low speed diesel engine, is applied to evaluate the efficiency. The result of the trial shows that there was no significant errors.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.9 no.5
• /
• pp.89-95
• /
• 2001

Recently GDI(Gasoline Direct Injection) engine is spotlighted to achieve higher thermal efficiency under partial loads and better performance at full loads. To realize this system, it is essential to make both stratified combustion and homogeneous combustion. When compared to PFI(Port Fuel Injection) engine, GDI engine needs more complicated control and optimal design with injection system. In addition, spray pattern must be optimized according to injection timing because ambient pressure in combustion chamber is also varied. Thus spray structure should be analyzed in details to meet various conditions. In this experimental study, two types of visualization system were developed to simulate compression stroke and intake stroke, respectively. With an increase of the ambient pressure, the penetration length tends to decrease due to rising resistance caused by the drag force of the ambient air. Spray characteristics impinged on the piston has a significant effect on mixture stratification around the spark plug. These results provide the information on macroscopic spray structure and design factors far developing GDI injector.

• Journal of ILASS-Korea
• /
• v.10 no.1
• /
• pp.43-52
• /
• 2005

The effect of fuel injection spray on engine performance has been known as one of the major concerns for improving fuel economy and reducing emissions. In general, reducing the spray droplet size could prevent HC emission in gasoline engine. As far as PFI (Port Fuel Injection) gasoline engine is concerned, the mixture of air and fuel may not be uniform under a certain condition, because breakup and production of spray droplets are made in a short distance between the fuel injector and intake valve. This study, by constituting PFI gasoline spray system, was performed to study the transient spray characteristics and dynamic behavior of droplets from 2hole 2spray type injector used in DOHC gasoline engine. Mean droplet size and optical concentration in accordance with various conditions were measured by LDPA and CCD camera. Through this study, the variation of drop size and optical concentration could be used for understanding the behavior of unsteady spray was declared and the existing the small droplets between each pulse spray could be estimated caused to the development of wall film was conformed.