• Journal of the Korean Chemical Society
• /
• v.61 no.6
• /
• pp.339-345
• /
• 2017

Carbonaceous adsorbent (CA-WTP) was prepared by heat treatment at $400^{\circ}C$ for 2 h in N2 atmosphere using waste tire powder (WTP). WTP and CA-WTP were first characterized by thermo-gravimetric analysis (TGA), energy dispersive X-ray spectrometer (EDS), scanning electron microscopy (SEM), specific surface area analysis (BET) and FT-IR spectroscopy. Then, they were tested as adsorbents for removal of Cd in water. CA-WTP exhibited much higher specific surface area and total pore volume than WTP itself and showed higher adsorption capacity for Cd. Equilibrium data of adsorption were analyzed using Freundlich and Langmuir isotherm models. It was seen that both Freundlich and Langmuir isotherms have correlation coefficient $R^2$ value larger than 0.95. The results of studies indicate that CA-WTP developed from WTP by heat treatment could be used as efficient adsorbent for the removal Cd from water.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.261-261
• /
• 2010

본 연구에서는 PBMS (Particle Beam Mass Spectrometer)와 ISPM (In-Situ Particle Monitor)을 연계하여 BPSG (Borophosphosilicate Glass) 및 PSG (Phosphosilicate Glass) 박막 증착을 위한 CVD (chemical vapor deposition) 공정 중 발생하는 오염입자 발생특성에 대해 비교 평가하였다. 소스는 TEB (Triethylborate), TEPO (Triethylphosphate) 및 TEOS (Tetraethoxysilane)를 사용하였고, 운반가스 및 반응가스로 He과 $O_2$ 및 $O_3$를 사용하였다. 증착온도와 압력은 각각 $450^{\circ}C$, 200 Torr 이었다. 반응기의 배기라인에 PBMS와 ISPM을 설치하고 500 nm 이하의 입자에 대해 공정단계별 시간에 따른 모니터링 결과 전 공정에 걸쳐 동일한 패턴의 입자발생분포를 보였으며, 특히 PBMS의 경우 ISPM의 입자측정한계인 260 nm 이하의 입자크기도 측정할 수 있었다. 입자발생이 안정적으로 일어나는 증착공정 중 PBMS를 통하여 입자크기를 측정한 결과 BPSG의 경우 약 110 nm, PSG의 경우 약 80 nm의 분포를 나타내었다. 이를 통해 TEB 소스가 배제된 PSG의 경우 BPSG의 경우보다 입자의 성장이 지체됨을 확인하였다. 측정에 대한 신뢰성을 확보하기 위해 PBMS 내의 TEM (Transmission Electron Microscopy) grid를 이용하여 입자를 샘플링 하였고, TEM 분석을 실시한 결과 PBMS 측정결과와 잘 일치하였다. 또한 EDS (Energy Dispersive Spectroscopy) 분석을 통하여 입자성분에 대해 검증하였다.

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.22 no.3
• /
• pp.224-234
• /
• 2012

Objectives: To assess the hazard of Korea chrysotile and anthophylite, fibers were analyzed for their physicochemical properties by transmission electron microscope equipped with energy dispersive X-ray spectrometer (TEM-EDS). Methods: To evaluate the biopersistence of 2 domestic asbestos, Sprague-Dawely rats were exposed to 2 mg asbestos by intratracheal instillation. Each asbestos (chrysotile ; $8,814,244{\times}10^6$ fibers/mg, average size $0.08{\mu}m{\times}4.39{\mu}m$, anthophyllite ; $5,182{\times}10^6$ fibers/mg, average size $0.95{\mu}m{\times}7.29{\mu}m$) were evaluated after a single intratracheal instillation. At times from 1 week to 4 weeks after exposure, the numbers of asbestos fivers in the bronchoalveolar lavage fluid and in the lung were calculated. Results: Anthophyllite fivers continuously have retained for 4 weeks but chrysotile fivers were rarely found at 4 weeks after exposure in the bronchoalveolar lavage fluid. Chrysotile fivers at 4 weeks after treatment were not observed but anthophyllite was easily observed in the lung with phase contrast microscopy. According to electron microscopic observation of asbestos in the lung, within 1 week after the administration of chrysotile fivers were decreased rapidly but anthophyllite fivers were very little change for 4 weeks. When chrysotile fivers have been lost Fe in 1 week, there were no significant changes in anthophyllite fivers in the lung. Conclusions: These findings indicate that after a long time exposure to chrysotile, asbestos bodies can not be found in the bronchoalveolar lavage fluid.

• Korean Chemical Engineering Research
• /
• v.60 no.1
• /
• pp.151-158
• /
• 2022

Iron and nitrogen coordinated carbon catalyst (Fe-N-C) is the most promising non-precious metal catalyst (NPMC) studied to alternate the Pt-group oxygen reduction reaction (ORR) catalyst. In this work, Fe/N/C type catalysts are prepared by four different nitrogen precursors; N, N, N', N'-tetramethylethylenediamine (TMEDA), 1,2-ethylenediamine (EDA), m-dicyanobenzene (DCB), dicyandiamide (DCDA) which can chelate a transition metal; In addition, the catalysts conducted the pyrolysis process at four different temperatures of 700, 800, 900, 1000 ℃ to investigate the ORR activities depend on pyrolysis temperature and to find an appropriate temperature. The characterizations of catalysts were investigated by scanning electron microscope-energy dispersive X-ray spectrometer (SEM-EDS), X-ray diffraction (XRD), and element analysis (EA). The electrocatalytic activity was measured by ORR polarization, also the electron transfer number was calculated from the slope of the K-L plot. The FeNC-EDA-800 which were prepared at pyrolysis temperature of 800 ℃ with EDA showed better ORR activity than the other catalysts.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.20 no.3
• /
• pp.107-112
• /
• 2010

The Cu$(In_{1-x}Ga_x)Se_2$ is the absorber material for thin film solar cell with high absorption coefficient of $1{\times}10^5cm^{-1}$. In the case of CIGS, the movable energy band gap from $CuInSe_2$ (1.00 eV) to $CuGaSe_2$ (1.68 eV) can be acquired while controlling Ga contain ratio. Generally, the co-evaporator method have used for development and fabrication of the CIGS absorption layer. However, this method should need many steps and lengthy deposition time with high temperature. For these reasons, in this paper, a new growth method of CIGS layer was attempted to hydride vapor transport (HVT) method. The CIGS mixed-source material reacted for HCl gas in the source zone was deposited on the substrate after transporting to growth zone. c-plane $Al_2O_3$ and undoped GaN were used as substrates for growth. The characteristics of grown samples were measured from SEM and EDS.

• Journal of Korean Society of Environmental Engineers
• /
• v.34 no.7
• /
• pp.473-479
• /
• 2012

Water reuse has been highlighted as a representative alternative to solve the lacking water resource. This study carried out a study on the pipe corrosion and water quality change which can occur through the supply of reclaimed water, using a simulated reclaimed water distribution pipeline. Galvanized steel pipe (GSP), cast iron pipe (CIP), stainless steel pipe (STSP) and PVC pipe (PVCP) were used for the pipe materials. Reclaimed water(RW) and tap water(TW) were respectively supplied into simulated reclaimed water distribution pipelines. As a result of performing a loop test to supply reclaimed water to simulated reclaimed water distribution pipelines, the weight reduction of pipe coupons showed the sequence of CIP > GSP > STSP ${\approx}$ PVCP. In addition, reclaimed water showed a high corrosion rate comparing to that of tap water. In case of CIP, the initial corrosion rate showed 3.511 mdd(milligrams per square decimeter per day) for reclaimed water and 2.064 mdd for tap water and the corrosion rate for 90 days showed 0.833 mdd for reclaimed water and 0.294 mdd for tap water. Also in case of GSP, the initial corrosion rate showed 2.703 mdd for reclaimed water and 2.499 mdd for tap water and the corrosion rate for 90 days showed 0.349 mdd for reclaimed water and 0.248 mdd for tap water, which was a tendency similar to that appeared in CIP with a tendency to reduce the corrosion rate. As a result of water quality changes of reclaimed water at pipe materials to carry out the loop test, there was higher conversion ratio of ammonia into nitrate in CIP and GSP with higher corrosion rate than that in STSP and PVCP where no corrosion has occurred. The highest denitrification rate of nitrate could be observed from CIP with the most particles generated from corrosion. In CIP, it could be confirmed that there was MIC (Microbiologically Induced Corrosion) as a result of EDS (Energy Dispersive X-ray spectrometer System) analysis results.

• Applied Chemistry for Engineering
• /
• v.28 no.5
• /
• pp.547-553
• /
• 2017

This study focused on the difference of photocatalytic performance by the incorporation of Pd into the $TiO_2$ framework and suggested five different catalysts composed of $TiO_2$ and x mol% $Pd-TiO_2$ (x = 0.25, 0.5, 0.75, and 1.0). A typical sol-gel method was used to synthesize catalysts, and the phenol photodegradation performance of each catalysts was evaluated. The physicochemical and optical properties of catalysts were confirmed by X-ray diffraction (XRD), transmission electron microscopy (TEM), scanning electron microscopy/energy dispersive spectrometer (SEM/EDS), ultraviolet/visible spectroscopy (UV/Vis), photoluminescence spectroscopy (PL), and photocurrent measurements. With the addition of Pd ions, the band gap of catalysts was shortened and the charge separation between photogenerated electrons and holes easily also occurred. As a result, the phenol photo-destruction performance over 0.75 mol% $Pd-TiO_2$ catalyst was 3 times higher than that of pure $TiO_2$. This is believed to be due to Pd ions acted as an electron capturing function during photocatalysis.

• Journal of the Korean Applied Science and Technology
• /
• v.33 no.4
• /
• pp.795-801
• /
• 2016

This study is on the denitrification process using the sodium alginate and $CaCl_2$ as a flocculant. Removal techniques of nitrate nitrogen from waste water are reverse osmosis, ion exchange, electro dialysis and biological method etc. We tried to remove nitrate nitrogen with flocculation and sedimentation method in the present study. Calcium alginate is expected to form a chelate bond with nitrate nitrogen in the solution. So the effects of flocculantt component, flocculation reaction time, molar ratio of the flocculant, flocculant injection rate are studied to determine the best removal rate of nitrate nitrogen. In addition, we tried to determine the nitrate nitrogen removal mechanism by analyzing the structure and component ratio of the configuration after the agglutination precipitate by FE-SEM and EDS. As a result, the nitrate nitrogen removal mechanism is turned out to form calcium-nitro-alginate, and the best mole ratio of flocculating agent is 1 : 1, the injection rate of the flocculant was up to 2%, the removal rate of the nitrate nitrogen to be 56.7% in the synthetic wastewater.

• Journal of the Mineralogical Society of Korea
• /
• v.29 no.1
• /
• pp.1-10
• /
• 2016

We studied the heavy minerals in 46 surface sediments collected from the Central Yellow Sea Mud (CYSM) to characterize the type, abundance, mineralogical properties and distribution pattern using the stereo-microscopy, field-Emission scanning electron microscopy (FE SEM) and chemical analysis through the energy dispersive spectrometer (EDS). Heavy mineral assemblages are primarily composed of epidote group, amphibole group, garnet group, zircon, rutile and sphene in descending order. Epidote group and amphibole group minerals account for more than 50% of total heavy minerals. The minerals in epidote group, amphibole group and garnet group in studied area are epidote, edenite and almandine, respectively. When we divided the CYSM into two regions by $124^{\circ}E$, the eastern region contain higher contents of epidote and (zircon + rutile), which are more resistant to weathering but lower of amphibole, which is less resistant to weathering than the western region. Based on this results, it is possible to estimate that the eastern region sediments are transported for a long distance while western region sediments are transported for a short distance from the source area. In the future, the additional study on the heavy minerals in river sediments flowing into the Yellow Sea and much more samples for marine sediments must be carried out to interpret exactly the provenance and sedimentation process.

• Journal of Korean Society of Environmental Engineers
• /
• v.39 no.9
• /
• pp.542-547
• /
• 2017

This paper was to analyze the membrane characterization of hydrophilicity, surface morphology and membrane chemical anlysis of three commercial microfiltration/ultrafiltration membranes, and evaluate the filtration performance of a seawater to assess the availability for pretreatment of desalination process. From the results of contact angle, Mem-3, fabricated with polyacrylonitrile, was highly hydrophilic. It find out that Mem-3 has more anti-biofouling property. In Field emission scanning electron microscope (FESEM), Mem-1 (polyethylene) and Mem-2 (Polyvinylidenefluoride) showed the sponge-like shape and Mem-3 showed finger-like shape. Membrane chemical analysis by energy dispersive spectrometer (EDS) presented that Mem-2 was mostly fluoride and Mem-3 had s high ratio of N (32.47%) due to the nitrile group. The permeation flowrate per time on suction pressures using deionized water (D.I. water) tends that permeation rate of Mem-3 more increased when the pressure was increased compared to other membranes. From the results of turbidity and total suspended solids (TSS) removal, turbidity of permeate was 0.191 NTU to 0.406 NTU and TSS was 2.2 mg/L to 3.0 mg/L in all membranes, indicating that it was not suitable for the pretreatment of seawater desalination by short-term experiments.