• Korean Chemical Engineering Research
• /
• 제56권3호
• /
• pp.381-387
• /
• 2018

Our study focuses on upgrading real biogas obtained under Indian scenario using carbon capture and utilization (CCU) technology to remove carbon dioxide ($CO_2$) and utilize it by forming metal carbonate. Amines such as monoethanolamine (MEA), diethanolamine (DEA), and sodium hydroxide (NaOH) were used to rapidly convert gaseous $CO_2$ to aqueous $CO_2$, and $BaCl_2$ was used as an additive to react with the aqueous $CO_2$ and rapidly precipitating the aqueous $CO_2$. All experiments were conducted at $25^{\circ}C$ and 1 atm. We analyzed the characteristics of the $BaCO_3$ precipitates using X-ray diffractometry (XRD), scanning electron microscopy - Energy dispersive spectroscopy (SEM-EDS) and Fourier-transform infrared spectroscopy (FT-IR) analyses. The precipitates exhibited witherite morphology confirmed by the XRD results, and FT-IR confirmed that the metal salt formed was $BaCO_3$, and EDS showed that there were no traces of impurities present in it. The quantity of the $BaCO_3$ was larger when formed with DEA. Also, a comparison was done with a previous study of ours conducted in Korean conditions. Finally, we observed that the carbonate obtained using real biogas showed similar properties to carbonates available in the market. An economic analysis was done to show the cost effectiveness of the method employed by us.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2009년 추계학술발표대회
• /
• pp.81-81
• /
• 2009

최근 휴대폰, 노트북 등과 같은 소형 멀티미디어 기기의 사용이 증가함에 따라 전자 패키징 산업은 경박단소화를 요구하고 있습니다. 더불어 전기적 신호의 손실을 줄이기 위해 전기, 전자산업체에서는 가볍고 굴곡성이 우수한 연성인쇄회로기판(Flexible Printed Circuit Board, FPCB)과 가격이 싸고 신뢰성이 입증된 경성인쇄회로기판(Rigid Printed Circuit Board, RPCB)의 전극간 접합에 많은 관심을 보이고 있습니다. 기존에 연성인쇄회로기판과 경성인쇄회로기판을 접합하는 방식으로는 connector를 이용한 체결법이 사용되고 있지만 완성품의 부피가 커지고 자동화 공정이 힘들며 I/O 개수가 제한적이어서 신호전달에 취약한 단점이 있습니다. 또한, 최근 FPCB를 RPCB에 접합하는데 interconnection으로 이방성 도전 필름(Anisotropic conductive film, ACF) 또는 비전도성 필름(Non-conductive film)이 널리 사용되고 있습니다. 하지만 필름의 가격이 비싸고, 낮은 전기 전도도를 보이며, 신뢰성 특성이 낮다는 단점을 가지고 있습니다. 본 실험에서는 기존의 connector 방식과 접착 필름을 이용한 방식을 대체하기 위하여 솔더를 interlayer로 이용하여 열과 압력으로 접합하는 방법에 대하여 연구하였습니다. 실험에 사용된 솔더의 조성은 Sn-3.0Ag-0.5Cu (in wt%)이고, RPCB와 FPCB의 표면처리는 ENIG로 하였습니다. 접합 온도와 접합 시간에 따라 최적의 접합 조건을 도출하고자 하였고, 접합된 시편을 가지고 신뢰성 테스트를 진행하였습니다. $85^{\circ}C$/85% 고온고습 시험과 고온 방치 시험을 통하여 접합부의 신뢰성을 테스트 하였고, 90도 Peel test로 기계적 접합 강도를 측정하였고, 파괴 단면을 Scanning Electron Microscopy (SEM), Energy-dispersive spectroscopy (EDS), X-ray photoelectron spectroscopy (XPS)로 분석하였습니다.

• Corrosion Science and Technology
• /
• 제9권5호
• /
• pp.223-232
• /
• 2010

NiTi alloy has been used for orthodontic wire due to good mechanical properties, such as elastic strength, friction resistance, and high corrosion resistance. Recently, these wire were coated by polymer and ceramic materials for aesthetics. The purpose of this study was to investigate electrochemical characteristics of tooth colored NiTi wire using various instruments. Wires (round type and rectangular type) were used, respectively, for experiment. Polymer coating was carried out for wire. Specimen was investigated with optical microscopy (OM), field emission scanning electron microscopy (FE-SEM) and energy dispersive x-ray spectroscopy (EDS). The corrosion properties of the specimens were examined using potentiodynamic tests (potential range of -1500 ~ 2000 mV) and electrochemical impedance spectroscopy (frequency range of 100 kHz ~ 10 mHz) in a 0.9 % NaCl solution by potentiostat. From the results of polarization behavior, the passive region of non-coated NiTi wire showed largely, whereas, the passive region of curved NiTi wire showed shortly in anodic polarization curve. In the case of coated NiTi wire, pitting and crevice corrosion occurred severely at interface between non-coated and coated region. From the results of EIS, polarization resistance(Rp) value of non-coated round and rectangular NiTi wire at curved part showed $5.10{\times}10^5{\Omega}cm^2$ and $4.43{\times}10^5{\Omega}cm^2$. lower than that of coated NiTi wire. $R_p$ of coated round and rectangular NiTi wire at curved part showed $1.31{\times}10^6{\Omega}cm^2$ and $1.19{\times}10^6{\Omega}cm^2$.

• 한국응용과학기술학회지
• /
• 제31권1호
• /
• pp.92-100
• /
• 2014

비이온계면활성제 가운데 솔비톨계 계면활성제인 Span을 이용해 수열합성법으로 수산화마그네슘을 합성하였다. 수산화마그네슘 합성의 전구체는 염화마그네슘과 수산화나트륨을 사용하였다. 비이온 계면활성제는 안정제와 분산제 그리고 표면 개질제로 적용하였다. 비이온 계면활성제를 첨가하였을 경우 수산화마그네슘 입자는 좀 더 작고 균일한 크기와 좋은 분산성을 나타내었으며, 소수성 성질을 나타내었다. 합성된 입자의 특성은 PSA, SEM, EDS, XRD 그리고 FT-IR을 통해 확인하였다. 기기 분석을 통해 개질 전과 후의 수산화마그네슘의 소수성, 분산성 특성을 비교하였다. 또한 실험조건에 따라 수산화마그네슘 입자의 표면 개질 특성 변화를 확인하였다.

• Environmental Engineering Research
• /
• 제23권3호
• /
• pp.301-308
• /
• 2018

We investigated simultaneous removal of heavy metals such as Cr, Ni, and Zn by adsorption onto powdered activated carbon (PAC) and PAC modified with sodium diethyldithiocarbamate (PAC-SDDC). Modification of PAC was confirmed by Fourier transform infrared spectroscopy and Scanning electron microscopy and energy dispersive X-ray spectroscopy. Both PAC and PAC-SDDC reached adsorption equilibrium within 48 h, and the adsorption kinetics followed a pseudo-second order reaction kinetics. The removal of metals was enhanced with increasing both adsorbent dosage and followed the descending order of Cr > Ni > Zn for PAC and Cr > Zn > Ni for PAC-SDDC, respectively. Adsorption kinetics followed pseudo-second order kinetics. Adsorption kinetic results were well fitted by the Freundlich isotherm except for Cr adsorption onto PAC. The optimum pH for heavy metal adsorption onto PAC was 5, whereas that for PAC-SDDC ranged from 7 to 9, indicating that modification of PAC with SDDC significantly enhanced heavy metal adsorption, especially under neutral and alkaline pH conditions. Our results imply that SDDC modified PAC can be applied to effectively remove heavy metals especially Cr in plating wastewaters without adjusting pH from alkaline to neutral.

• 한국물환경학회지
• /
• 제34권6호
• /
• pp.621-631
• /
• 2018

In this study, catalyst was made through incipient wetness method using palladium (Pd) as noble metal, indium (In) as secondary metal, and montmorillonite (MK10) and Al pillared montmorillonite (Al-MK10) as supporters. The nitrate reduction rate of the catalysts was measured by batch experiments where H2 gas was used as reducing agent and formic acid as pH controller. Transmission electron microscopy (TEM) equipped with energy dispersive spectroscopy (EDS) and X-ray photoelectron spectroscopy (XPS) were all used to determine the elemental distribution of Pd, In, Al, and Si on catalysts. It was observed that Al pillaring increased the Al/Si elemental composition ratio and point of zero charge of MK10, but decreased its BET specific surface area and pore volume. The nitrate reduction rate of Al-MK10 Pd/In was 2.0 ~ 2.5 times higher than that of MK10 Pd/In using artificial groundwater (GW) in ambient temperature and pressure. Nitrate reduction rates in GW were 1.2 ~ 1.7 times lower than those in distilled deionized water (DDW). Nitrate reduction rates in acidic conditions were higher than those in neutral condition in both GW and DDW. The amount of produced NH3-N over degraded NO3- at acid conditions was lower than that of neutral condition. Even though the leaching of Pd after reaction was measured in DDW it was not detected when both Al-MK10 Pd/In and MK10 Pd/In were used in GW. The modification of montmorillonite as a supporter significantly increased the reductive catalytic activities of nitrates. However, the ratio of producing ammonia by-products to degraded nitrates in ambient temperature and pressure was similar.

• Journal of Microbiology and Biotechnology
• /
• 제33권7호
• /
• pp.895-908
• /
• 2023

Disposal of waste containing heavy metals into the environment is a major threat to human health and can result in toxic or chronic poisoning in aquatic life. In the current study, metal-resistant Raoultella ornithinolytica was isolated from metal-contaminated samples collected from the Tanjaro River, located southwest of Sulaymaniyah, Iraq. R. ornithinolytica was identified by partial amplification of 16S rRNA. The uptake potency of heavy metals was assessed using inductively coupled plasma-optical emission spectroscopy (ICP-OES) and indicated that R. ornithinolytica removed 67, 89, 63.4, 55.6, 56.5, 65, and 61.9% of Cd, Pb, Cr, Ni, Zn, Co, and Fe, respectively. These removal rates were influenced by temperature, pH, and contact time; at 35℃ and pH 5 with a change in the incubation time, the reduction rate improved from 89 to 95% for Pb, from 36.4 to 45% for Cu, and from 55.6 to 64% for Ni. Gene analysis indicated that R. ornithinolytica contained pbrT, chrB, nccA, iroN, and czcA genes, but the pcoD gene was absent. Energy-dispersive X-ray spectroscopy (EDS) images showed evidence of metal ion binding on the cell wall surface with different rates of binding. Transmission electron microscopy (TEM) detected different mechanisms for metal particle localization; cell surface adsorption was the main mechanism for Pb, Zn, and Co uptake, while Cd, Ni, and Fe were accumulated inside the cell. The current study describes, for the first time, the isolation of R. ornithinolytica from metal-contaminated water, which can be used as an eco-friendly biological expedient for the remediation and detoxification of metals from contaminated environments.

• 전기화학회지
• /
• 제13권2호
• /
• pp.89-95
• /
• 2010

Cu(In, Ga)$Se_2$ (CIGS) 박막은 다원화합물이기 때문에 제조공정이 매우 까다롭다. 진공장치를 사용하는 제조 방법으로 동시증착법, 스퍼터링법 +셀렌화가 있고, 비진공 제조 방법으로 전기화학적인 전착법이 있다. 각 방법에 있어서도 출발 물질의 종류에 따라 다양한 제조 방법이 동원 될 수 있다. 진공증착에 의한 방법은 고품질의 박막을 얻는데 사용 되고 있으나 고가의 진공장비가 사용되므로 대면적화에 따른 제조비용 측면에서 문제가 있다. 이에 비하여, 전착법은 간단하면서도 저가로 대면적화를 이룰 수 있다는 장점 때문에, 많은 관심이 기울여지고 있다. 본 연구에서는 Mo/Glass전극위에 Ga/(In + Ga) = 0.3의 성분비를 만족시키는 CIGS 박막을 전기화학적으로 제조하기 위하여, $Cu^{2+}$, $In^{3+}$, $Ga^{3+}$, $Se^{4+}$ 4성분을 모두 포함하는 전해질 수용액 내에서, 4성분의 이온들이 동시에 환원되는 전위를 조절하여 CIGS 박막을 전착 하였다. SEM을 이용하여 얻어진 CIGS 박막의 전착된 시료의 표면을 관찰하였고, EDS로 그 조성을 분석하였다. 또한, XRD를 이용하여 전착시료의 열처리 전후의 결정성변화를 조사하였다.

• 반도체디스플레이기술학회지
• /
• 제8권4호
• /
• pp.65-69
• /
• 2009

Carbon nanotubes (CNTs) were coated with undoped zinc oxide (ZnO) or 5 wt% gallium-incorporated ZnO (GZO) using various deposition conditions. The CNTs were directly grown on conical-type tungsten substrates at $700^{\circ}C$ using inductively coupled plasma-chemical vapor deposition. The pulsed laser deposition technique was used to deposit the ZnO and GZO thin films with very low stress. Field-emission scanning electron microscopy and high-resolution transmission electron microscopy were used to monitor the variations in the morphology and microstructure of CNTs prior to and after ZnO or GZO coating. The formation of ZnO and GZO films on CNTs was confirmed using energy-dispersive x-ray spectroscopy. In comparison to the as-grown (uncoated) CNT emitter, the CNT emitter that was coated with a thin (10 nm) GZO film showed remarkably improved field emission characteristics, such as the emission current of $325\;{\mu}A$ at 1 kV and the threshold field of $1.96\;V/{\mu}m$ at $0.1\;{\mu}A$, and it also exhibited the highly stable operation of emission current up to 40 h.

• 한국재료학회지
• /
• 제24권2호
• /
• pp.111-115
• /
• 2014

Titanium and its alloys are useful for implant materials. In this study, porous Ti-Nb-Zr biomaterials were successfully synthesized by powder metallurgy using a $NH_4HCO_3$ as space holder and $TiH_2$ as foaming agent. Consolidation of powder was accomplished by spark plasma sintering process(SPS) at $850^{\circ}C$ under 30 MPa condition. The effect of high energy milling time on pore size and distribution in Ti-Nb-Zr alloys with space holder($NH_4HCO_3$) was investigated by optical microscope(OM), scanning electron microscope(SEM) & energy dispersive spectroscopy(EDS) and X-ray diffraction(XRD). Microstructure observation revealed that, a lot of pores were uniformly distributed in the Ti-Nb-Zr alloys as size of about $30-100{\mu}m$ using mixed powder and milled powders. In addition, the pore ratio was found to be about 5-20% by image analysis, using an image analyzer(Image Pro Plus). Furthermore, the physical properties of specimens were improved with increasing milling time as results of hardness, relative density, compressive strength and Young's modulus. Particularly Young's modulus of the sintered alloy using 4h milled powder reached 52 GPa which is similar to bone elastic modulus.