• The Korean Journal of Ceramics
• /
• v.6 no.3
• /
• pp.229-235
• /
• 2000

The spherical silica powder was synthesized by varying the kinds of solvent and mixing energy in emulsion method. The stirring speed varied from 500 to 1000 r.p.m. at 5$0^{\circ}C$ for 2h. Toluene in benzyl groups and a series of alkanes were used as dispersant. The average size of spherical silica particles decreased with increasing the stirring speed and the chain length o solvents used in this work. The average size was controlled in the range of 134~28$\mu\textrm{m}$ by selecting a proper solvent and stirring speed. The optimum processing parameters were described in details.

• Elastomers and Composites
• /
• v.33 no.2
• /
• pp.110-116
• /
• 1998

A new technology was introduced to the emulsion polymerization. It is the ultrasonic activation method which replaced a chemical initiator and the environmentally benign process. In this study, free radicals were produced by a pulse type ultrasound energy irradiation, then polystyrene latex was polymerized without chemical initiator. With ultrasonic energy density, the degree of polymerization, average molecular weight, and particle size were increased, but the polydispersity index for the molecular weight and the particle size were decreased. The optimum condition of emulsifier concentration and temperature was found to be 1.0 wt.% SDS and $40^{\circ}C$, respectively. As a result, the emulsion polymerization process without chemical initiator was proved to be comparable to common latex properties such as average molecular weight, molecular weight distribution, particle size, etc.

• Journal of Ceramic Processing Research
• /
• v.13 no.spc1
• /
• pp.145-148
• /
• 2012

Spherical silica aerogel powders were fabricated via an emulsion polymerization method from a water glass. A water-in-oil emulsion, in which droplets of a silicic acid solution are emulsified with span 80 (surfactant) in n-hexane, was produced by a high power homogenizer. After gelation, the surface of the spherical silica hydrogels was modified using a TMCS (trimethylchlorosilane)/n-hexane solution followed by solvent exchange from water to n-hexane. Hydrophobic silica wet gel droplets were dried at 80 ℃ under ambient pressure. A perfect spherical silica aerogel powder between1 to 12 ㎛ in diameter was obtained and its size can be controlled by mixing speed. The tapping density, pore volume, and BET surface area of the silica aerogel powder were approximately 0.08 g·cm-3, 3.5 ㎤·g-1 and 742 ㎡·g-1, respectively.

• Applied Chemistry for Engineering
• /
• v.9 no.2
• /
• pp.294-299
• /
• 1998

To prove pseudo-homopolymerization(PHP) method indirectly for general system which includes more than one growing radicals per particle, Mayo-Lewis equation of bulk copolymer system was derived form probability equation about instantaneous copolymer composition of emulsion copolymer system during interval II. From Extended Smith-Ewart equation proposed by Ballard et al. in emulsion copolymerization, exact solution was obtained for 0-1 system (i.e., the system containing no more than one growing radical per particle). From the exact solution, average number of radicals per particle and instantaneous copolymer composition were predicted to reach the steady state which a few minutes. So the reliability of this approximation method could by proved directly for 0-1 system. Styrene-butadiene(St-Bu) and Styrene-methyl methacrylate (St-MMA) system were used for model calculations.

• Journal of the Korean Applied Science and Technology
• /
• v.21 no.3
• /
• pp.191-196
• /
• 2004

An emulsion of octadecamidoethylaminoethyl dodecate (which provides softness) and an emulsion silicone oil KF-96 (which provides lubricity) were separately synthesized. Then PP finishing softeners (SSA-7) was prepared by blending of the synthesized emulsions with beef tallow hardened oil (a softness improving agent). PP finishing treatment was carried out with the prepared SSA-7 and PP finishing resin by a one bath method, and several physical properties were tested. As a result, crease recovery, tear strength, softness, lubricity, and bending resistance were all good, indicating that the prepared SSA-7 is a good PP finishing softener.

• Journal of the Korean Ceramic Society
• /
• v.27 no.4
• /
• pp.487-494
• /
• 1990

$Al_2O_3$-20w/o $ZrO_2$ composite powders were prepared by the emulsion-coprecipitation method and the effects of preparative conditions on powder characteristics were investigated. In the preparation of $Al_2O_3$-$ZrO_2$ composite powders, toluene was used instead of kerosene as the oil phase in emulsions. After coprecipitation, the emulsion was easily broken into a single liquid phase by adding methanol, and then precipitates could be effectively collected by filteration. The fact that all $ZrO_2$ phases present at room temperature in composite powders calcined at $1100^{\circ}C$ after washed by methanol had a tetragonal structure confirmed that methanol-washing enhanced the dispersibility of fine $ZrO_2$ particles in $Al_2O_3$ matrix. $Al_2O_3$-$ZrO_2$ composite powders were spherical particles of 0.2${\mu}{\textrm}{m}$ diameter. Pellets sintered at $1650^{\circ}C$ for 2hrs showed the relative theoretical density of 97.3% and the fracture toughness of 5.01MN/$m^{3/2}$.

• Bulletin of the Korean Chemical Society
• /
• v.33 no.7
• /
• pp.2320-2324
• /
• 2012

A novel approach for metabolite extraction and fingerprinting was introduced based upon the nano-baskets and emulsion liquid membrane-nuclear magnetic resonance (ELM-NMR) technique. The objective of this method is optimizing the fingerprints, minimizing the metabolic variation from analysis, increasing the likelihood differences, and obtaining the maximum extraction yield. Low molecular weight metabolites in rat serum were recovered by ELMs using 12 nano-baskets of calixarene, as both emulsifier and carrier. The yields of ELMs were optimized by the method of one-at-a-time. According to NMR data, the maximum metabolic variation was achieved using scaffold 4 (4 wt %), n-decane membrane, stirring rate of 300 rpm, treat and phase ratios of 0.3 and 0.8, respectively. The results revealed that some calixarenes tend to extract non-specific macromolecules; and repeatability of fingerprints for 7-mediated ELM was maximum and for 3-mediated ELM was minimum. The yield of extractions was obtained to be higher for n-decane and lower for carbon tetrachloride. Among different membranes, the fingerprints by chlorinated liquid membranes were more repeatable than using toluene or n-decane.

• Korean Journal of Materials Research
• /
• v.16 no.6
• /
• pp.355-359
• /
• 2006

Fine silica powders were synthesized via w/o emulsion method using sodium silicate, ammonium sulfate, Triton N-57, and cyclohexane as silica source, precipitating agent, surfactant, and oil phase, respectively. The powders were prepared under a conventional process and an ultrasonic process using the same reactants at room temperature for 1 hr varying the concentration of $Na_2SiO_3$ solution and the mol ratio of $H_2O$/surfactant, respectively. The particle size of the silica powder was reduced with decreasing the concentration of sodium silicate solution and with increasing the mol ratio of $H_2O$/surfactant under with and without ultrasounds. The size of powder with ultrasounds was smaller than that without ultrasounds, which indicates that the application of ultrasound in the synthesis of silica powder is an efficient way to reduce particle size.

• Korean Journal of Food Science and Technology
• /
• v.31 no.4
• /
• pp.1077-1083
• /
• 1999

This study was aimed to evaluate the effectiveness of hydrophilic, lipophilic antioxidants and emulsifiers by HLB (hydrophilic lipophilic balance) in different oil systems. Lipophilic antioxidant (${\delta}-tocopherol$), hydrophilic antioxidant (gallic acid) and emulsifier(lecithin, tween 20, span 60) were evaluated in relation to oil stability in bulk oil system (soybean oil) and emulsified with Tween 80 at $60^{\circ}C$. In the storage test ($60^{\circ}C$), gallic acid was more effective on the stability of oil oxidation than ${\delta}-tocopherol$ in bulk and emulsion system. Lecithin as a hydrophilic emulsifier was more effective than tween 20 on the stability of oil oxidation in bulk and emulsion system. Also span 60, a lipophilic emulsifier, was more effective than tween 20, a hydrophilic emulsifier, in bulk and emulsion systems.

• Macromolecular Research
• /
• v.9 no.5
• /
• pp.267-276
• /
• 2001

In order to endow with new bioactive functionality from demineralized bone particle (DBP) as natural source to poly(L-lactide) (PLA) synthetic biodegradable polymer, porous DBP/PLA as natural/synthetic composite scaffolds were prepared and compared by means of the emulsion freeze drying and solvent casting/salt leaching methods for the possibility of the application of tissue engineered bone and cartilage. For the emulsion freeze drying method, it was observed that the pore size decreased in the order of 79$\mu\textrm{m}$ (PLA control) > 47$\mu\textrm{m}$ (20% of DBP) > 23 $\mu\textrm{m}$ (40% of DBP) > 15$\mu\textrm{m}$ (80% of DBP). Porosities as well as specific pore areas decreased with increasing the amount of DBR. It can be explained that DBP acts like emulsifier resulting in stabilizing water droplet in emulsion. For the solvent casting/salt leaching method, a uniform distribution of well interconnected pores from the surface to core region were observed the pore size of 80 ∼70 $\mu\textrm{m}$ independent with DBP amount. Porosities as well as specific pore areas also were almost same. For pore size distribution by the mercury intrusion porosimeter analysis between the two methods, the pore size distribution of the emulsion freeze drying method was broader than that of the solvent casting/salt leaching method due to the mechanism of emulsion formation. Scaffolds of PLA alone, DBP/PLA of 40 and 80%, and DBP powder were implanted on the back of athymic nude mouse to observe the effect of DBP on the induction of cells proliferation by hematoxylin and eosin staining for 8 weeks. It was observed that the effect of DBP/PLA scaffolds on bone induction are stronger than PLA scaffolds, even though the bone induction effect of DBP/PLA scaffold might be lowered than only DBP powder, that is to say, in the order of DBP only > DBP/PLA scaffolds of 40 and 80% DBP > PLA scaffolds only for osteoinduction activity. In conclusion, it seems that DBP plays an important role for bone induction in DBP/PLA scaffolds for the application of tissue engineering area.