• Structural Engineering and Mechanics
• /
• 제26권5호
• /
• pp.591-615
• /
• 2007

An improvement is introduced to solve the plane problems of linear elasticity by reciprocal theorem for orthotropic materials. This method gives an integral equation with complex kernels which will be solved numerically. An artificial boundary is defined to eliminate the singularities and also an algorithm is introduced to calculate multi-valued complex functions which belonged to the kernels of the integral equation. The chosen sample problem is a plate, having a circular or elliptical hole, stretched by the forces parallel to one of the principal directions of the material. Results are compatible with the solutions given by Lekhnitskii for an infinite plane. Five different orthotropic materials are considered. Stress distributions have been calculated inside and on the boundary. There is no boundary layer effect. For comparison, some sample problems are also solved by finite element method and to check the accuracy of the presented method, two sample problems are also solved for infinite plate.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 춘계학술대회
• /
• pp.7-12
• /
• 2004

Large-sized pins are usually used to lift and handle large low speed diesel engine crankshaft. There has then been a need to reduce and optimize the weight of the traditionally used pins. Making an hole by cutting the inside of the pin out was investigated in view of static and fracture strength. To compensate the stress increase caused by the introduction of the inner hole, the groove in the circumferential direction pre-existing on the pin is to be removed. Finite element analysis was carried out for both the original model and weight reduced model. Stress intensity factors for semi-elliptical defects assumed on the pin for the original model and weight reduced model was calculated using the ASME method and compared with the fracture toughness test result of the pin material. The diameter of the cutting hole for the revised model was determined based on the analysis results.

• 한국추진공학회지
• /
• 제21권5호
• /
• pp.19-28
• /
• 2017

본 연구에서는 원형 노즐과 타원형 노즐을 이용하여 공동현상과 수력튀김 현상이 유동특성에 어떠한 영향을 미치는지 파악하고자 하였다. 이를 위해 오리피스 길이 대 직경비(L/d)와 타원형 노즐의 종횡비(a/b)가 서로 다른 분사기들을 제작하여 분무실험을 수행하였다. 분사압력 증가에 따라 공동현상이 발생할 경우 유량계수가 서서히 감소하였으나 수력튀김 영역에서는 유량계수가 급격히 떨어진 후 일정한 값을 유지함을 확인하였다. 하지만 타원형 노즐에서 장축지름(a)과 단축지름(b) 대비 오리피스 길이의 비인 L/b가 8 이상, L/a가 8 이하인 경우, 유량계수 및 액체제트 형상은 기존의 원형 노즐과는 상당히 다른 결과를 나타내었다. 정상유동 상태인 경우 타원형 노즐에서 분사된 액주는 원형 노즐과는 달리 하류로 가면서 장축에서는 분무각이 감소하였으며 단축에서는 분무각이 커지는 모습을 보였다.

• 천문학회보
• /
• 제36권2호
• /
• pp.61.1-61.1
• /
• 2011

We have performed simultaneous observations at 22GHz and 43GHz on AGNs hosted by elliptical galaxies using KVN radio telescope. We have constructed the sample, based on two major surveys in radio and optical band, i.e. Faint Images of the Radio Sky at Twenty-Centimeters (FIRST) and Sloan Digital Sky Survey (SDSS) DR7, respectively. We restricted the redshift range 0.01 < z < 0.06 and the absolute magnitude Mr < -19.4 in order to satisfy volume limited sample. We also checked clear detection of four distinctive emission lines ([NII], [OIII], $H{\alpha}$, $H{\beta}$) so as to utilize on BPT diagram, distinguishing AGNs from star-forming galaxies. Elliptical galaxies have been selected by visual inspection making use of SDSS optical images. Then, we cross-matched the elliptical galaxies with FIRST detections. About 35% of the galaxies have been detected throughout KVN observations. We derive spectral index, applying the flux of different radio frequencies from FIRST (1.4GHz) and KVN (22GHz) and classify into steep, flat or inverted spectrum. We have found that most of the detected galaxies have flat spectrum while the rest of them have steep spectrum. This implies that a number of detected galaxies might have compact structure associated with the central region of the galaxies. The relation between black hole mass and radio luminosity has shown relatively tighter correlation in high frequency than in low frequency, which confirms that high frequency in radio band is appropriate to study the center of the galaxies.

• Journal of Mechanical Science and Technology
• /
• 제15권4호
• /
• pp.413-421
• /
• 2001

A simple procedure to add and remove material simultaneously along the boundary is developed to optimize the shape of a two dimensional elastic problems and to minimize the maximum von Mises stress. The results for the two dimensional infinite plate with a hole, are close to the theoretical results of an elliptical boundary and the stress concentration is reduced by half for the fillet problem. The proposed shape optimization method, when compared with existing derivative based shape optimization methods has many features such as simplicity, applicability, flexibility, computational efficiency and a much better control on stresses on the design boundary.

• Macromolecular Research
• /
• 제11권5호
• /
• pp.357-367
• /
• 2003

The linear low density polyethylene (LLDPE)/zeolite composite using novel inorganic filler, zeolite, is prepared by a conventional compounding procedure using a twin-screw extruder. The observed scanning electron microscopic (SEM) morphology shows a good dispersion and adhesion of zeolite in the LLDPE matrix. The mechanical properties in terms of the Young's modulus, the yield stress, the impact strength, and the elongation at break were enhanced with a successive increment of zeolite content up to 40 wt%. The X-ray diffraction measurement is of supportive for the improved mechanical properties and the complex melt viscosity is as well. Upon applying a certain level of strain on the composites, the dewetting, the air hole formation and its growth are characterized. The dewetting originates around the filler particles at low strain and induces elliptical micropores upon further stretching. The microporosity such as the aspect ratio, the number and the total area of the air holes is also characterized. Thus, the composites loaded 40 % zeolite and 300 % elongation may be applicable for breathable microporous films with improved modulus, impact and yield stress, elongation at break, microporosity and air hole properties.

• 대한토목학회논문집
• /
• 제2권3호
• /
• pp.1-13
• /
• 1982

원구멍과 타원구멍을 갖는 두 개의 강판(鋼板)에 완전교번하중(完全交番荷重)(completely reversed load, completely alternating load ;같은 크기의 인장(引張) 압축(壓縮)의 반복)을 가할 때 유한요소법(有限要素法)을 써서 강복요소(降伏要素)가 발생하는 단계마다 각 절점(節點)의 변위(變位), 각 요소(要素)의 응력(應力) 및 변형률(變形率), 하중(荷重)의 크기 등을 계산하여 파괴력학적(破壞力學的)인 검토를 행하였다. 이로부터, 강판(鋼板)의 파괴기구(破壞機構)를 밝히는 데에 핵심이 된다고 생각되는 응력확대계수(應力擴大係數)를 계산할 수 있는 토대가 마련되었으며, 흠선단(先端)의 응력집중(應力集中)현상과 소성역(塑性域)의 변화과정이 밝혀졌다. 또, 재하(載荷) 중에 강복(降伏)을 경험한 부분에서는 강하(降荷)때에 영구변형(永久變形)(잔류변형(殘留變形))이 남게 되고 이것이 나머지의 제하(除荷)를 구속(拘束)하여 반대방향의 재하(載荷)의 효과를 일으킴으로서 흠선단(先端)에 가까운 부분에는 인장(引張) 후의 제하(除荷) 때에 심지어 압축재강복(壓縮再降伏)까지, 압축(壓縮) 후의 제하(除荷) 때에는 심지어 인장재강복(引張再降伏)까지 일으키며 이들이 인장(引張) 및 압축(壓縮)의 재하(載荷) 중의 강복(降伏)과 교번(交番)으로 반복됨으로써 흠선단(先端)에 파로(波勞)현상을 초래하게 된다는 사실을 예견할 수 있었다. 아울러 흠이 원구멍일 때와 타원구멍일 때의 계산결과를 비교하여 홈이 예리한 균열에 가까워질수록 빨리 파괴에 달하게 된다는 사실을 확인할 수 있었다.

• 천문학회보
• /
• 제46권2호
• /
• pp.69.2-69.2
• /
• 2021

We present the discovery of rare active galactic nuclei (AGNs) in nearby (z<0.05) compact elliptical galaxies (cEs) located in isolated environments. Using spectroscopic data from the Sloan Digital Sky Survey (SDSS) Data Release 12, four AGNs were identified based on the optical emission-line diagnostic diagram. SDSS optical spectra of AGNs show the presence of distinct narrow-line emissions. Utilizing the black hole (BH) mass-stellar velocity dispersion scaling relation and the correlation between the narrow L([OIII])/L(Hβ) line ratio and the width of the broad Hα emission line, we estimated the BH masses of the cEs to be in the range of 7×10⁵-8×10⁷ solar mass. The observed surface brightness profiles of the cEs were fitted with a double Sérsic function using the Dark Energy Camera Legacy Survey r-band imaging data. Assuming the inner component as the bulge, the K-band bulge luminosity was also estimated from the corresponding Two Micron All Sky Survey images. We found that our cEs follow the observed BH mass-stellar velocity dispersion and BH mass-bulge luminosity scaling relations, albeit there was a large uncertainty in the derived BH mass of one cE. In view of the observational properties of BHs and those of the stellar populations of cEs, we discuss the proposition that cEs in isolated environments are bona fide low-mass early-type galaxies (i.e., a nature origin).

• 한국분무공학회지
• /
• 제22권3호
• /
• pp.146-152
• /
• 2017

An experimental study was carried out to investigate the spray characteristics of non-circular effervescent twin-fluid nozzles. For this purpose, two types of non-circular nozzles (E1, E2) and circular nozzle (C) were used. Three types of aerorators with hole diameters of 1.2, 1.7 and 2.1 mm were used. Each aerorator has a total of 12 holes. It is defined by area ratio which is ratio of exit orifice area and aerator hole area. Experiments were carried out by controlling the amount of air flowing after fixing the flow rate of the liquid, and the nozzle internal pressure and SMD were measured, and the jet image was taken from the nozzles. The discharge coefficients of the three kinds of nozzles were compared with the used in plain orifice's equation and the Jedelsky's equation, and the Jedelsky's equation was found to be about 3 times larger. In addition, empirical formula based on ALR, which is the largest variable in Jedelsky's equation, was derived. The droplet sizes(SMD) were found to be smaller in the non-circular shape than in the circular shape, which is concluded to be caused by the difference of the discharge coefficients.

• 한국진공학회지
• /
• 제22권5호
• /
• pp.262-269
• /
• 2013

집속 이온빔 장비는 나노크기의 패턴을 제작하는 한 방법이지만, 정밀한 제작은 쉽지 않다. 그러므로 집속 이온빔 장비로 샘플을 제작할 때 고려해야 하는 공정 조건을 정리하여 초보자도 샘플제작이 가능하도록 도움을 주고자 한다. 본 장비로 원하는 나노크기의 패턴을 제작하기 위해서 집속 이온빔 장비의 공정변수들을 최적화 하는 과정이 중요하다. 가공할 때 고려해야 하는 변수에는 빔 전류량(빔 크기)과 도즈(빔 지속시간)가 있다. 도즈를 결정한 후에 패턴을 제작하는데 걸리는 시간과 패턴의 크기를 고려하여 빔 전류량을 선택하면 된다. 여기서 도즈는 제작하려는 나노크기의 패턴의 금속 두께에 따라 결정이 된다. 이 논문에서 최적화한 1 pA의 빔 전류와 $0.1nC/{\mu}m^2$의 도즈의 공정조건에서 100 nm 두께의 금 박막 위에 타원형의 구멍을 정밀하게 제작할 수 있다.