• Corrosion Science and Technology
• /
• 제23권1호
• /
• pp.54-63
• /
• 2024

This work investigated the influence of concentration and applied potential on the characteristics of zinc powder (purity, apparent density, morphology, particle size distribution, and particle zeta potential) produced by the electrochemical process from waste brass. High-purity zinc powder is obtained using selective leaching of industrial brass waste in acidic, neutral, and alkaline solutions. The free immersion method with and without voltage using linear polarization technique is used. In the electrochemical process, hydrochloric acid HCl in three different concentrations (0.1, 0.2, and 0.3) M is used. The time and the distance between the electrodes are set to be 30 min and 3 cm, respectively. It has been found that the percentage purity is 98%, 96%, and 94% for the acidic, neutral, and alkaline solutions, respectively. In addition, the morphology of zinc powder analyzed by SEM was dendritic and mossy. It has been recorded that the purity of zinc increases with the increase of the concentration and applied potential. The highest value of purity for zinc powder was %98.58 in 1000 mV and 0.3M concentration for graphite cathode.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1995년도 추계학술대회 논문집
• /
• pp.190-193
• /
• 1995

MCFC has been investigated for the last half centry as an alternative energy source. The operating temperature of MCFC is 650$^{\circ}C$, so it is more efficient than ocher fuel cells, and it has needed no nob metal element for the electrodes. we investigated electrochemical characteristics of separator for MCFC.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2003년도 가을 학술발표회 논문집
• /
• pp.663-666
• /
• 2003

Using numerical analysis modeling of Multi-electrode Array that could be applied to the corrosion state measurement of a reinforcing steel bar in concrete, the steel bar location inside concrete can be probed by the investigation of the change of the measured impedance from concrete surface determined by the electrical impedance of interface between the steel bar and concrete, the electrical resistivity of concrete, the array of electrodes and the relative location and diameter of the steel bar.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2018년도 춘계학술대회 논문집
• /
• pp.67-67
• /
• 2018

The 5xxx series aluminum alloys are recently used in not only marine system but also automotive area because of a low density material, good mechanical properties and better resistance to corrosion. However, Aluminum alloys are less resistant than the purest aluminum such as 1xxx aluminum alloy. Electrochemical anodization technique has attracted in the area of surface treatment because of a simple procedure, a low-cost efficiency than other techniques such as lithography and a large volume of productivity, and so on. Here, The relationship between the corrosion behavior and the thickness of aluminum anodic oxide have been studied. Prior to anodization, The 5052 aluminum sheets ($30{\times}20{\times}1mm$) were degreased by ultra-sonication in acetone and ethanol for 10 minutes and eletropolished in a mixture of perchloric acid and ethanol (1:4, volume ratio) under an applied potential of 20V for 60 seconds to obtain a regular surface. During anodization process, Aluminum alloy was used as a working electrode and a platinum was used as a counter electrode. The two electrodes were separated at a distance of 5cm. The applied voltage of anodization is conducted at 40V in a 0.3M oxalic acid solution at $0^{\circ}C$ with appropriate magnetic stirring. The surface morphology and the thickness of AAO films was observed with a Scanning Electron Microscopy (SEM). The corrosion behavior of all samples was evaluated by an open-circuit potential and potentio-dynamic polarization test in 3.5wt% NaCl solution. Thus, The corrosion resistance of 5052 aluminum alloy is improved by the formation of an anodized oxide film as function of increase anodization time which artificially develops on the metal surface. The detailed electrochemical behavior of aluminum 5052 alloy will be discussed in view of the surface structures modified by anodization conditions such as applied voltages, concentration of electrolyte, and temperature of electrolyte.

• Corrosion Science and Technology
• /
• 제7권6호
• /
• pp.319-323
• /
• 2008

The polarization resistance of mild steel in 0.5M hydrochloric acid has been evaluated by using impedance (Z) and linear polarization (LPR) techniques and compared to the noise resistance obtained from electrochemical noise data. The degree of localization of this general corrosion has also been discussed by evaluating localization index and power spectral density. Polarization resistance obtained by LPR technique ($28\Omega$) was higher than that obtained by impedance technique ($15\Omega$). Noise resistance ($11\Omega$) was much lower than polarization resistance measured by both of above techniques. Higher polarization resistance obtained by LPR technique is generally caused by passivation effect in the presence of scales or deposits which can introduce an increased resistance as can low conductivity electrolytes. The reason why noise resistance is lower than polarization resistance is the effect of background noise detected by using three platinum electrodes cell in 0.5M hydrochloric acid. Slope($-\beta$) of power spectral density (PSD) obtained from analysis of noise data ($-\beta$ = 3.3) was much higher than 2 which indicates mild steel corroded uniformly. Localization index (LI) calculated from statistical analysis (LI=0.08) is much lower than 1 which indicates that mild steel did not corroded locally. However, LI value is still higher than $1x10^{-3}$ and this indicates that mild steel corroded locally in microscopic point of view.

• 콘크리트학회논문집
• /
• 제21권2호
• /
• pp.153-158
• /
• 2009

콘크리트 표면에 4개의 전극배열을 이용한 비파괴 표면측정법을 통하여 철근의 피복을 벗겨내지 않고도 콘크리트 내 철근의 부식상태 및 철근의 배치상태를 추정할 수 있다. 표면측정법 모델링은 부식된 철근과 주위 콘크리트사이의 계면 임피던스가 콘크리트 표면에서 측정된 임피던스와 어떤 관련이 있는지를 보여준다. 본 연구에서는 콘크리트에 매립된 철근 크기와 콘크리트 피복두께 등의 탐지를 위하여 철근부식 표면측정 모델링을 이용하였다. 모델링 결과 철근 크기가 D10에서 D35로 커짐에 따라 표면임피던스 변화가 나타났으며, 또한 콘크리트 피복두께가 0.02 m에서 0.1 m로 커짐에 따라 그 변화에 대한 영향이 표면측정 임피던스를 통해 나타났다. 그러므로 표면측정법 모델링을 통하여 콘크리트 내 철근부식반응을 시뮬레이션 할 수 있으며, 동시에 철근직경과 매입 깊이 등에 대한 정보도 얻을 수 있음 알 수 있다.

• 전기화학회지
• /
• 제6권2호
• /
• pp.113-118
• /
• 2003

폴리아닐린 분말과 고분자 계면활성제, cyclohexanone용매를 micro-milling장치내에서 분산시켜 (m입자 크기를 갖는 가공용이한 분산액을 제조하였다. 분산액을 백금 전극 위에 코팅하여 얻은 분산박막의 전기화학적 특성들은 순환전압전류법(CV)을 이용하여 조사하였다. CV의 결과에 의하면 폴리아닐린 분산박막이 순수한 폴리아닐린 박막과 유사한 전기화학적 특성을 갖는 것으로 나타났다. $3wt.\%$ NaCl용액에서 수행한 분극실험과 열린회로전위 측정 실험에서는 PANI분산액을 철표면에 코팅하면 부식전위가 증가하였다. 분산박막/철 전극의 열린회로전위값(OCP, Voc)이 분산액의 제조 조건에 따라 변화가 있음을 관찰하였다. 이러한 결과들은 본 연구에서 사용한 전도성 고분자 분산액이 철의 부식방지코팅물질로서 유용성을 갖고 있다는 것을 보여주고 있다.

• Corrosion Science and Technology
• /
• 제6권5호
• /
• pp.261-268
• /
• 2007

Embedded sensors were used as an in-situcorrosion-sensing device for aircraft and vehicular structures protected by organic coatings. Results are presented changes associated with a standard Airforce aircraft coating and a standard Army vehicle coating were monitored by embedded sensors. These coatings consisted of a polyurethane topcoat and an epoxy primer, however are formulated to provide different characteristics. The ac-dc-ac testing method was used to accelerate the degradation of these coatings while being immersed in a NaCl medium. Electrochemical impedance spectroscopy and electrochemical noise measurement experiments were used to monitor the induced changes. A comparison of the results between coatings subjected to the ac-dc-ac exposure and coatings subjected to only constant immersion in the NaCl medium is presented. The results were used to demonstrate the effectiveness of the ac-dc-ac method at accelerating the degradation of an organic coating without observably changing the normal mechanism of degradation. The data highlights the different features of the coating systems and tracks them while the coating is being degraded. The aircraft coating was characterized by a high-resistant topcoat that can mask corrosion/primer degradation at the primer/substrate interface whereas the vehicle coating was characterized by a low-resistant topcoat with an effective corrosion inhibiting primer. Details of the ac-dc-ac degradation were evaluated by using an equivalent circuit to help interpret the electrochemical impedance data.

• 전기화학회지
• /
• 제16권1호
• /
• pp.9-18
• /
• 2013

Zinc air 전지의 구성요소와 전지의 특징을 설명하였다. 리튬 이온 전지에 비해 월등히 높은 에너지 밀도를 가지고 있지만, 충전의 비가역성으로 인한 낮은 용량 유지 특성 때문에 zinc air 이차전지는 아직 상용화되지 못하였다. Zinc air 전지는 충방전에 관여하는 반응들의 속도가 느려서 그 반응들의 속도를 촉진해야 하는 특징이 있는가 하면 동시에 부식과 수소발생 반응의 속도는 오히려 느리게 해야 하는 까다로운 조건을 만족해야 한다. 기존의 전지들과 비교하면, 기초연구뿐 아니라, 전지의 기계적구조, 부식, 복합소재적인 요소의 적용이 더욱 필요한 연구분야라고 하겠다. 출력개선과 부식방지 그리고 공기의 공급에 대비한 물의 증발의 억제 등은 상충하는 성질을 동시에 만족해야 하는 복합소재의 특성이다.

• 한국수소및신에너지학회논문집
• /
• 제10권3호
• /
• pp.177-184
• /
• 1999

The charge-discharge characteristics of the $Mg_2Ni-x$ wt.%Nd (x = 0~3) electrodes were investigated. The electrodes were prepared by the mechanical grinding of the induction-melted $Mg_2Ni$ alloy powders with Ni and/or Nd using planetary ball mill apparatus. The discharge capacity of the $Mg_2Ni$ alloy increased with the increase in the nickel content. The electrode possessing 100 wt.% nickel powder showed the initial capacity of 760 mAh/g and the capacity decay with the cycle number was less than that of the 55 wt.% nickel powder. The Nd was added to this composition. It was found that the $Mg_2Ni-100$ wt.%Ni -0.2 wt.%Nd alloy showed an excellent charge-discharge cycle characteristics compared with the other reported Mg-Ni alloy system. The discharge capacity was 400 mAh/g after 70 cycles. Such an improved cycle life seems to be attributed to the improvement in the corrosion characteristics of the alloy. The anodic polarization curve of the $Mg_2Ni-100$ wt.%Ni-0.2 wt.%Nd alloy exhibited better passivating behavior than that of the $Mg_2Ni-100$ wt.%Ni.