• Journal of Korean Tunnelling and Underground Space Association
• /
• v.21 no.2
• /
• pp.267-278
• /
• 2019

Variety of tunnel ahead prediction methods have been performed for safe tunnel construction during tunnel excavation. Pole-pole array among the electrical resistivity survey, which is one of the tunnel ahead prediction method, has been utilized to predict water-bearing sediments or weak zone located within 5 times of tunnel diameter. One of the most important processes is the estimation of virgin ground resistivity and it can be obtained from the following process: 1) calculation of contact area between the electrodes and the medium, and 2) assumption of the electrodes as equivalent spherical electrodes which have a same surface area with the electrodes. This assumption is valid in a small contact area and sufficient distance between the electrodes. Since the measured resistance, in general, varies with the electrode size, shape, and distance between the electrodes, it is necessary to evaluate the influence of these factors. In this study, theoretical equations were derived and experimental tests were conducted considering the electrode size, shape, and distance of cylindrical electrodes which is the most commonly utilized electrode shape. Through this theoretical and experimental study, it is known that one should be careful to use the assumption of the equivalent half-spherical electrode with large ratio between the penetrated depth and radius of the cylindrical electrode, as the error may get larger.

• Journal of Hydrogen and New Energy
• /
• v.19 no.2
• /
• pp.163-170
• /
• 2008

Carbon nanofibers with nano-sized structures were evaluated as a active material using supercacitor electrode which could store electrochemical energy reversibly. A feasibility of EDLC electrode was estimated with specific surface area measurement by BET method and mesopore structure of carbon nanofiber surface could be explained electrochemical absorption-desorption in aqueous electrolyte. A capacitance of carbon nanofiber electrode was increased gradually, depending on the ratio of Ketjenblack as a conducting material. Ketjen Black $20{\sim}25\;wt.%$ ratio in electrode was observed a suitable amount of conducting material by cyclic voltametry results.

• Journal of the Korean Electrochemical Society
• /
• v.6 no.2
• /
• pp.158-160
• /
• 2003

We have reported to make nanostructured cobalt oxide electrode that have large capacitance over than 400 F/g (specific capacitance) and good cycleability. But, it had serious demerits of low voltage range under 0.5 V and low power density. Therefore, we need to increase voltage range of cobalt oxide electrode. We report here on the electrochemical properties of sol-gel-derived nanoparticulate cobalt xerogel in 1M KOH solution and aqueous polymeric gel electrolyte. In solution electrolyte, cobalt oxide electrode had over 250 F/g capacitance consisted of EDLC and pseudocapacitance. In gel electrolyte, cobalt oxide electrode had around 100 F/g capacitance. This capacitance was only electric double layer capacitance of active surface area. In solution electrolyte, potassium ion as working ion reacted with both of layers easily. However, In gel electrolyte, reacted with only surface-active layer. Itis very hard to reach resistive layer. So, we have studied on pretreatment of electrode to contain working ions easily. We'll report more details.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2004.11a
• /
• pp.305-308
• /
• 2004

There are ground facility of maintenance in house electric facility of infra maintenance electric home appliances having used multifariousness in house, that use electric energy of common source for equipment. The body of building such as the reinforced concrete construction is structurally united, and the electric resistance is also small. It is possible that those foundations have contacted the ground at large surface area and that it substitutes the building construction body for the earth electrode. This is called "the structure earthing". This method has been defined at electrical facilities technical standards and KS in our country, and it has been used in various quarters practically. However, in our country, there is no example of using the foundation of the house as substitution earth electrode practically, and the means of the evaluation as electrode has not been established either. Then, in this paper, basic research for utilizing foundation of the house as substitution earth electrode is carried out.

• Journal of Hydrogen and New Energy
• /
• v.18 no.4
• /
• pp.446-451
• /
• 2007

Physicochemical properties of carbon nanofibers were evaluated as a supercacitor electrode materials could store electrochemical energy reversibly. A capacitance of carbon nanofiber electrode was increased gradually, depending on the PVDF binder ratio. A feasibility of EDLC electrode was estimated with specific surface area measurement by BET method and mesopore structure of carbon nanofiber surface could be explained electrochemical absorption-desorption in aqueous electrolyte. PVDF 5 wt.% ratio in electrode was observed a suitable binder amount by CV result.

• Journal of Information Display
• /
• v.3 no.2
• /
• pp.13-18
• /
• 2002

Numerical simulation is one of the most useful tools to study gas discharge phenomena that occur in alternating current plasma display panel (AC-PDP) cell. Most PDP cell simulations have been performed for two-dimensional cell, is cross-section along the address electrode. We developed a three-dimensional PDP simulator and applied it to a T-shaped electrode cell in order to show the effects of sustain electrode shape that cannot be included in two-dimensional simulation. The dependence of power consumption on electrode shape and area in the simulation showed the same trend as experiment.

• Journal of the Korean Society for Precision Engineering
• /
• v.25 no.7
• /
• pp.139-144
• /
• 2008

Micro electrochemical machining was investigated to machine micro internal features. This method uses a micro disk tool electrode and can easily machine micro features inside of a micro hole, which are very difficult to make by the conventional processes. In order to limit the machining area and localize the electrochemical dissolution, ultra short pulses were used as power source and a micro disk electrode with insulating layer on its surface was used as a tool electrode. By electrochemical process, internal features, such as groove array, were fabricated on the stainless steel plate.

• Journal of Information Display
• /
• v.2 no.1
• /
• pp.5-9
• /
• 2001

New types of ac plasma display panel (PDP) cells are designed and tested electro-optically. We proposed two types of sustaining electrode to improve the luminous efficiency. One is the meander electrode, which has longer discharge path length and smaller electrode area than conventional type. The other is the bridge-shaped electrode, which eliminates the transparent electrode near the barrier ribs. They show higher luminous efficiency and lower power consumption than conventional type.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.30 no.3
• /
• pp.59-64
• /
• 2016

Applications of electrolytic ion water generated by the oxidation-reduction have gradually been expanded due to their strong sterilizing power and a surface active force. We demonstrate the effect of the multi-layer type electrode for effective ion water generation. The multi-layer type electrode has ability to generate stronger acid and alkali water by increase of the electrode reactive area. Also power consumption efficiency enhances because the electrodes disposed in middle position of the reactive cell raise the usage rate by overlapped effect as an electrolysis electrode.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.04a
• /
• pp.47-48
• /
• 2006

Electrowetting phenomenon is applied in the various field of technology. One of that is electrowetting display as a paper like electronic paper. Fast response and easy to express a color is goodness. In spite of that, the oil movement of the electrowetting display is irregular. So it doesn't look like uniform. Because of the above reason, electrowetting display using patterned electrode is made and the characteristic of oil movement is observed. Electrode and polymer wall is patterned by photo-lithography. We analyze the oil movement according to the variation of size and the position of etched electrode area.