• Archives of Pharmacal Research
• /
• 제24권4호
• /
• pp.355-359
• /
• 2001

A novel HPLC method with electrochemical detection has been developed for the determination of recombinant human epidermal growth factor (rhEGF) in pharmaceutical products. rhEGF was separated from other components in formulation on a reversed-phase C18 column with 24% acetonitrile in 0.1 M phosphate buffer (pH 4.75). The optimum electrochemical oxidation of EGF was obtained at 0.85 V vs. Ag/AgCl in a glassy carbon working electrode due to electroactive tyrosine, tryptophan, methionine, and arginine residues. The quantitation range was from 1.0 to 200 ng of rhEGF with the linear correlation coefficient greater than 0.999. The method was successfully applied for the quantitation of rhEGF in a pharmaceutical preparation.

• Nuclear Engineering and Technology
• /
• 제47권7호
• /
• pp.849-858
• /
• 2015

This study set the pyroprocess facility at an engineering scale as a cost object, and presented the cost consumed during the unit processes of the pyroprocess. For the cost calculation, the activity based costing (ABC) method was used instead of the engineering cost estimation method, which calculates the cost based on the conceptual design of the pyroprocess facility. The calculation results demonstrate that the pyroprocess facility's unit process cost is $194/kgHM for pretreatment, $298/kgHM for electrochemical reduction, $226/kgHM for electrorefining, and $299/kgHM for electrowinning. An analysis demonstrated that the share of each unit process cost among the total pyroprocess cost is as follows: 19% for pretreatment, 29% for electrochemical reduction, 22% for electrorefining, and 30% for electrowinning. The total unit cost of the pyroprocess was calculated at $1,017/kgHM. In the end, electrochemical reduction and the electrowinning process took up most of the cost, and the individual costs for these two processes was found to be similar. This is because significant raw material cost is required for the electrochemical reduction process, which uses platinum as an anode electrode. In addition, significant raw material costs are required, such as for $Li_3PO_4$, which is used a lot during the salt purification process.

• Journal of Electrochemical Science and Technology
• /
• 제13권1호
• /
• pp.90-99
• /
• 2022

Owing to the rising concern of global warming, lithium-ion batteries have gained immense attention over the past few years for the development of highly efficient electrochemical energy conversion and storage systems. In this study, alpha-phase VOPO₄·2H₂O with nanosheet morphology was prepared via a facile hydrothermal method for application in high-performance lithium-ion batteries. The X-ray diffraction and scanning electron microscopy (SEM) analyses indicated that the obtained sample had an alpha-2 (αII) phase, and the nanosheet morphology of the sample was confirmed using SEM. The lithium-ion battery with VOPO₄·2H₂O as the anode exhibited excellent long-term cycle life and a high capacity of 256.7 mAh g^-1 at room temperature. Prelithiation effectively improved the specific capacity of pristine VOPO₄·2H₂O. The underlying electrochemical mechanisms were investigated by carrying out AC impedance, rate capability, and other instrumental analyses.

• 한국표면공학회지
• /
• 제42권5호
• /
• pp.197-202
• /
• 2009

The electrodeposition in acidic aqueous electrolyte bath of cadmium telluride on gold electrodes has been studied by electrochemical analysis. Conventional cyclic voltammetry using potentiostat is considered as a reliable method to study electrochemical behavior of electrodeposition of CdTe. In this paper, the mechanism of CdTe deposition and its cyclic voltammetry were studied with the Te ion concentration, temperature, potential, and scan rate. We also investigated surface morphologies using FESEM and atomic composition of Cd and Te using EDS. Atomic composition of Cd and Te were varied with Te ion concentration in the electrolyte.

• Transactions on Electrical and Electronic Materials
• /
• 제13권4호
• /
• pp.177-180
• /
• 2012

In this study, we prepared $LiFePO_4$- poly (sodium 4-styrenesulfonate) (PSS) composite by the hydrothermal method and ball-milling process. Different wt% PSS were added to $LiFePO_4$. The cathode electrodes were made from mixtures of $LiFePO_4$-PSS: SP-270: PVDF in a weighting ratio of 70%: 25%: 5%. $LiFePO_4$-PSS powders were characterized by X-ray diffraction (XRD), and scanning electron microscopy (SEM). The electrochemical properties of $LiFePO_4$-PSS/Li batteries were analyzed by cyclic voltammetry, charge/discharge tests, and AC impedance spectroscopy. A Li/$LiFePO_4$-PSS battery with 4.75 wt% PSS shows the best electrochemical properties, with a discharge capacity of 128 mAh/g.

• E2M - 전기 전자와 첨단 소재
• /
• 제9권2호
• /
• pp.165-173
• /
• 1996

We prepared polythiophene and poly(3-methylthiophene) films, known as conducting polymer, by electrochemical method. Polythiophene and poly(3-methylthiophene) films were doped and undoped dopant for the studing the understanding of doping mechanism and possible application to the color change switch. We observed that the anodic, cathodic wave and absorption spectra were slightly changed during doping and undoping process in polythiophene. It shows that doping and undoping process were showed some difference by the appearance and disappearance of polaron and bi-polaron. In the relation of the peak of oxidative current density and potential sweep rate of cyclic voltammograms, the amount of dopant in polythiophene film was homogeneously increased at low scan rate. This also can be applied to the poly(3-methlythiophene).

• 대한기계학회논문집A
• /
• 제22권1호
• /
• pp.44-51
• /
• 1998

In order to develop the evaluation methods of degradation for the Ni-Cr-Mo-V steel, which is in use for turbine rotor in nuclear power plant, the degraded materials were prepared by simulated degradation methods. The result of impact test and fatigue crack growth test shows that the FATT(Fracture Appearance Transition Temperature) and fatigue crack growth rate increased with the increase of degradation. And the result of new electrochemical polarization test method was suggested for the evaluating FATT, fatigue crack growth exponent and coefficient C values based on the results of relationship between corrosion current density(Icorr) & FATT, and the m & C and Icorr.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2013년도 제44회 동계 정기학술대회 초록집
• /
• pp.262-262
• /
• 2013

In surface chemistry area, many scientists studied the electrochemical reaction by changing work-function of metal; however, these methods had the weakness that it did not create the electric field. Unlike earlier studies, our capacitor-method makes a strong electric field in ice film. This electric field was induced by soft landing $Cs^+$ ions on ice film, and the strength was measured by the vibrational Stark shift of acetonitrile. In our system, the electric field strength is $10^9$ V/m and it is almost same in the electrochemical cell. This capacitor model provides new method to investigate the electrochemical reaction in vacuum system.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 1998년도 하계종합학술대회논문집
• /
• pp.398-400
• /
• 1998

In this paper, the etching studies for n-GaN were carried out using the wet chemical, the photo-enhanced-chemical, and the electro-chemical etching methods. The experimental results show that n-GaN is etched in diluted NaOH solution at room temperture and the etched thickness of NaOH and electron concentrations. Te etching rate of n-GaN samples with n.simeq.1*10$^{19}$ cm$^{-3}$ were used to compare the photo-enhanced-chemical etching with the electrochemical etching methods. The removed thickness was 680.angs./25min by the electrochemical etching methods. The removed thickness was 680 .angs./25min by the electrochemical etching method ad 784.angs./25min by the photoenhanced-chemical etching method. The patterns are 100.mu.m*100.mu.m rectangulars covered with SiO$_{2}$film. It is shown that the profile of etched side-wall of the pattern is vertical without dependance of the n-GaN orientations.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2000년도 영호남학술대회 논문집
• /
• pp.301-306
• /
• 2000

This paper describes on the fabrication of a SOI substrate by SDB technology and electrochemical etch-stop. The surface of the thinned SDB SOI substrate is more uniform than that of grinding or polishing by mechanical method, and this process was found to be a very accurate method for SOI thickness control. During electrochemical etch-stop, leakage current versus voltage curves were measured for analysis of the open current potential(OCP) point, the passivation potential(PP) point and anodic passivation potential. The surface roughness and the controlled thickness selectivity of the fabricated a SDB SOI substrate were evaluated by using AFM and SEM, respectively.