• Proceedings of the Korea Association of Crystal Growth Conference
• /
• 1998.06a
• /
• pp.39-43
• /
• 1998

Single crystals of{{{{ { Zn}_{ 1-x} {Mn }_{x }{Te} }}}} with x=0.3-0.6 were prepared by the standard Bridgeman method. Diffuse neutron diffraction intensities due to the short range magnetic ordering is found in the vicinities of 1 1/2 0 reciprocal point and its equivalent point, indicating that the magnetic correlation of the clusters is the type III antiferromangetic one do the F-type Bravais class crystals, being identical with that of {{{{{ Cd}_{ 1-x} {Mn }_{x }Te }}}}. Neutron inelastic scattering measure-ment has been performed for {{{{{ Zn}_{ 0.6} { Mn}_{ 0.4}Te }}}} sample using the cold neutron spectrometer. AGNES. High resolution measurement with the energy resolution of {{{{ TRIANGLE E= +- .01meV}}}} was carried out in the temperature range from 10K to the ambient. Critical scattering, closely related with the spin glass transition, has been observed for the first time in this semimagnetic semi-conductor. The critical scattering is observed at temperatures in the vicinity of the spin glass transition temperature, 17K. The scattering is observed as a kind of quasielastic scattering in the reciprocal range where the elastic magnetic diffuse scattering has been observed, e.g., 11/20 reciprocal point, indicating the spin fluctuation has dynamic components in this material. Photoconductivity has been discovered below 150K in {{{{{ Zn}_{ 0.4} {Mn }_{0.6 } Te}}}}. The electric AC conductivity has been increased dramatically under the laser light with the wave lengths of {{{{ lambda =6328,5145 and4880 }}}}$\AA$ ,respectively. After the light was darkened, the conductivity was reduced to the original level after about 2000 seconds at 50K, being above the spin glass transition temperature. This phenomenon is the typical persistent photoconductivity; PPC which was similarly found in {{{{ { Zn}_{ 1-x} { Mn}_{x} Te}}}}.

• Journal of the Korean Geographical Society
• /
• v.32 no.2
• /
• pp.141-153
• /
• 1997

In Korea, cable television(CATV) broadcasting has begun in March, 1995. This Paper aims at examining the location of CATV broadcasting station, and demand density(numbers of viewer houshold) of broadcasting area, and at clarifing the factors affecting subscription. The results are as follows: The number of CATV stations is 54 in 1996, and these CATV stations are mainly located in larger cities. The correlation between the number of established or planned CATV station and the number of household is very high. In sphered broadcasting area Permitted in 1997, the location of CATV station is about 73,000 household and 230,000 persons in the minimum values of household and population, and diameter of sphered broadcasting area is 40.6 km in mean. The factors affecting subscription rates of CATV are median age and supply rates of apartment of each dong in Chongju city and each myun in Chongwon county. The correlation between subscription rates of CATV and supply rates of apartment appears higher than correlation between subscription rates and median age other factors based on residual analysis of regression equation are established period of transmission network of CATV and acceptance attitude of dwellers.

• Journal of the Korean Geotechnical Society
• /
• v.16 no.4
• /
• pp.201-208
• /
• 2000

Axial load distribution in model piles was measured by fiber Bragg Grating(FBG) sensor to investigate a possibility of analyzing the load transfer mechanism by Fiber Optic sensor system. Since FBGs of different wave lengths can be multiplexed in an optical fiber, the installation of sensor system and the measurement of strains are relatively simple, compared with consisting strain gages. In this study, FBG sensors and electric strain gages were embedded in the same piles and the distributions of load transfer by two sensor systems were measured. It was observed from the test results that the variations of axial load by both systems showed insignificant difference and that the measurements by FBG were smoother than those by strain gage. Under the environments of laboratory testing, survival rate of embedded FBG system was higher than that of strain gage. Therefore, it was concluded that the use of FBG sensor has a great potential for the measurement of load transfer for pile foundation.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.25 no.3
• /
• pp.339-347
• /
• 2014

In this paper, the authors present a new design for a broad-band metamaterial(MTM) absorber that utilizes flexible substrate. The proposed MTM unit cell is constructed by a electric-inducive-capacitive(ELC) resonator and a cut-wire on the same side of the flexible polyimide substrate. To reduce the radar cross section at frequencies other than the targeted frequency bands, the metallic pattern layer of the proposed structure is placed facing toward the incident wave propagation direction. A prototype absorber was fabricated with a planar array of $33{\times}45$ unit cells. Our experiments showed that the proposed absorber exhibits a peak absorption rate of 92 % and 93 % at 9.06 GHz and 15.0 GHz, respectively, and 75 % of the full-width at half-maximum(FWHM) bandwidth is achieved. The proposed backplane-less MTM structure can be used for a broad-band microwave absorber and irregular surface applications.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.51 no.10
• /
• pp.256-263
• /
• 2014

We have designed and made three kinds of FBG(Fiber Bragg Grating) Acoustic Transducer using Hopper type WDM on the use of recently developed FBG in Korea. The newly designed three kinds of FBG Acoustic Transducer using Hopper type WDM have an excellent merit of practical use with simple structure of sensors arm as well as the merit with existing fiber sensors. It was possible to detect sound waves in the range of 10 Hz to 18 kHz through the newly designed three kinds of FBG Acoustic Transducer and also, possible to detect its signal within the maximum range of 8.6 m by the use of most suitable resonance condition of the transducer. Especially, we can expect the utilization of low-frequency signal detection instead of existing acoustic sensor in the environment of electric noise and inferior condition. Furthermore, they can be developed as the high-sensibility and multi-point signal detection system through the sensor array system.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.29 no.1
• /
• pp.15-20
• /
• 2009

The results of crack evaluation by conventional UT(Ultrasonic Test)is highly depend on the inspector's experience or knowledge of ultrasound. Phased array UT system and its application methods for small crack length evaluation will be a good alternative method which overcome present UT weakness. This study was aimed at checking the accuracy of crack length evaluation method by electronic scanning and discuss about characteristics of electronic scanning for crack length evaluation. Especially ultrasonic phased array with electronic scan technique was used in carrying out both sizing and detect ability of crack as its length changes. The response of ultrasonic phased array was analyzed to obtain the special method of determining crack length without moving the transducer and detect-ability of crack minimal length and depth from the material. A method of crack length determining by electronic scanning for the small crack is very real method which has it's accuracy and verify the effectiveness of method compared to a conventional crack length determination.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.19 no.4
• /
• pp.386-392
• /
• 2009

This paper reports on the research which investigates acoustic signals acquired in progressive compressing, hole blanking, shearing and burr compacting process. The work piece is the head pin of the electric connector, whose raw material is the preformed steel bar. An acoustic sensor was set on the bed of hydraulic press. Because the acquired signals include the dynamic characteristics generated for all the processes, it is required to investigate signal characteristics corresponding to unit process. The corresponding dynamic characteristics to the respective process were first studied by analyzing the signals respectively acquired from compressing, blanking and compacting process. The combined signals were then periodically analyzed from the grinding to the grinding in the sound frequency domain and in the ultrasonic wave. The frequency of around 9 kHz in the sound frequency domain was much correlated to the tool wear. The characteristic frequency in the acoustic emission domain between 100 kHz and 500 kHz was not only clearly observed right after tool grinding but its amplitude was also related to the wear. The frequency amplitudes of 160 kHz and 320 kHz were big enough to be classified by the noise. The noise amplitudes are getting bigger, and their energy was much bigger as coming to the next regrinding. The signal analysis was based on the real time data and its frequency spectrum by Fourier Transform. As a result, the acousto-ultrasonic signals were much related to the tool wear progression.

• Journal of the Korean Magnetics Society
• /
• v.12 no.2
• /
• pp.68-72
• /
• 2002

In this research, the effects of capacitance to the access time were studied at the junction area of tunneling magnetoresistance when these were used as memory devices. These results were obtained by applying electric signal input and magnetic field was not used. We applied bipolar square waves of 1MHz to the MTJ samples to obtain the results and time constant ($\tau$) calculated by observing wave responses utilizing an oscilloscope. And time constant was compared with junction area. Each part of MTJ sample, such as electrical pad, lead and contact area, was modeled as an electrical equivalent circuit based on experimental results. For the 200㎛$\times$200㎛ cell, junction capacitance was 90 pF. Also, measurement and simulation results were compared, which showed those similarity.

• The Journal of Natural Sciences
• /
• v.9 no.1
• /
• pp.131-143
• /
• 1997

The authors studied clothing buying motive and clothing buying behavior. The date were obtained from 352 women college students living in Seoul and Taejon. As the result of factor analysis. four buying motive factors were found: fashion and individuality, economy, status, advertising and impulsive buying. Three buying behaviors(information using, clothing selection standard, and shop selection standard) were factor analyzed. Three factors were founded in information using: human, electric wave communication, advertising and observation factors. Four factors were found in clothing selection standard: utility, design, marketing, fashion and status. Two factors were found in shop selection standard: merchandise and service. Clothing buying motive and clothing buying behavior were related, and they were different according to the levels of spending money and major in college.

• Geophysics and Geophysical Exploration
• /
• v.8 no.2
• /
• pp.184-190
• /
• 2005

We have attempted to give some physical into the factors that control the response of subsurface target to plane wave excitation at VLF (very low frequency) frequencies. Although the VLF technique has some serious disadvantages, such as a lack of penetration depth and limited frequencies, its advantages are also extremely important to have made it by far the most popular electromagnetic technique in current use. In the magnetic-field measurement mode these lightweight, relatively low-priced tools allow us to survey large areas rapidly and inexpensively, to locate and roughly define subsurface electrical conductors. When used in the electric-field mode the technique is, in simple environments, capable of quantitative interpretation and once again the speed and relative cheapness of these devices makes them a natural 'first electromagnetic tool ' to use in reconnaissance mapping.