• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.33 no.2
• /
• pp.93-100
• /
• 2009

Characteristics of micro-sonic/supersonic axi-symmetric jet impinging on a flat plate with a pre-drilled hole were both experimentally and numerically studied, to observe the role of assist-gas jet to eject melted materials from the cut zone in the laser machining. For various Mach numbers of the nozzle and the total pressures of the assist gas, detailed impinging jet flow structures over the plate and the variations of mass flux through the pre-drilled hole were observed. It was found that the present experimental and numerical results show a good agreement, which proves the accountability of the present work. From the present study, it was also observed that the mass flow rate through the hole was closely related with the total pressure loss caused by the Mach disc on the work piece, and that supersonic nozzle could perform more efficient roles as blowing the assist-gas jet in the laser machining, as compared to sonic nozzles.

• Journal of the Korean Society for Precision Engineering
• /
• v.16 no.11
• /
• pp.197-203
• /
• 1999

Increasing demands on precision machining have necessitated the tool to move not only position error as small as possible, but also with smoothly varying feedrates. Because of the lack of accurate and efficient algorithms for generation of 3-dimensional lines and circles, a full accomlishment for available machine tool resolution is generally unavailable. In this paper, a reference-pulse type 3-axis PC_NC milling system is developed for the precision machining of complex shapes in 3-dimensional space. Three AC servomotors are used as the actuator instead of the hand wheel to operate a 3-axis milling machine under the same mechanical structure. A PC is used to handle the control signal calculation for various types of motion command. To achieve the synchronous 3-axis motion, a real-time reference-pulse 3-dimensional linear and circular interpolator based on the intersection criteria is developed in software. The performance test via computer simulation and actual machining have shown that the PC-NC milling system is useful for the machining of arbitrary lines and circles in 3-dimensional space.

• Journal of Korean Society for Quality Management
• /
• v.20 no.1
• /
• pp.136-146
• /
• 1992

Most of scheduling papers on FMS have been considered that the fabrication process, the machining process and the assembly process etc. are independent and the releasing, routing, dependent, batching, loading problem are treated separetely. In this paper, we discuss that the integrated scheduling problem which can be solved for efficient use. We combine two systems that each process system which in order to produce a product is treated dependently, the releasing and the routing problem are combined one system and we present the efficient flexible manufacturing system as including the alternate process.

• Journal of Mechanical Science and Technology
• /
• v.18 no.12
• /
• pp.2095-2103
• /
• 2004

A macro-level CAPP system is proposed to plan the complicated mechanical prismatic parts efficiently. The system creates the efficient machining sequence of the features in a part by analyzing the feature information. Because the planning with the individual features is very complicated, feature groups are formed for effective planning using the nested relations of the features of a part, and special feature groups are determined for sequencing. The process plan is generated based on the sequences of the feature groups and features. When multiple machines are required, efficient machine assignment is performed. A series of heuristic rules are developed to accomplish it.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2007.11a
• /
• pp.123-124
• /
• 2007

• Laser Solutions
• /
• v.14 no.2
• /
• pp.17-23
• /
• 2011

Active thin films are ubiquitous in the manufacture of all forms of flat panel display (FPD). One of the most widely employed thin films is indium tin oxide (ITO) and metal films used electrically conductive materials in display industries. ITO is widely used for fabrication of LCD, OLED device, and many kinds of optical applications because of transparency in visible range and its high conductivity and metal films are also widely employed as electrodes in various electric and display industries. It is important that removing specific area of layer, such as ITO or metal film on substrate, to fabricate and repair electrode in display industries. In this work, we demonstrate efficient selective ablation process to ITO and aluminum film on glass using a femtosecond laser (${\lambda}p=1025nm$) respectively. The femtosecond laser with wavelength of 1025nm, pulse duration of 400fs, and the repetition rate of 100kHz was used for selectively removing ITO and Al on glass in the air. We can successfully remove the ITO and Al films with various pulse energies using a femtosecond laser.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.23 no.6 s.165
• /
• pp.1011-1017
• /
• 1999

Electrolytic in-process dressing grinding technique which enables application of metal bond wheels with fine superabrasives in mirror surface grinding operations has developed. It is possible to make efficient precision machining of hard and brittle material such as ceramic and hard metal by the employment of this technique. However, in order to ensure the success of performances such as efficient machining, surface finish, and surface quality, it is important to sustain the insulating layer that has sharply exposed abrasives in wheel surface. Using AE(Acoustic Emission) sensor, this paper will show whether the insulating layer sustains stably or not in real grinding time. And by comparing AErms value and surface roughness their thresholds for stable electrolytic in-process dressing grinding will be determined.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.17 no.4
• /
• pp.1-8
• /
• 2018

In drilling Inconel 601, which is used for compressor cases in aircraft engines, a lot of cutting oil must be supplied. This prevents tools from wear and fracture due to the heat buildup resulting from the high-temperature resistance and toughness of this alloy. However, the cutting oil supply has compromised the machining environment. This has caused attention to shift to an environmentally friendly cutting fluid supply system called the Minimum Quantity Lubrication(MQL) system. The aim of this study was to find a more efficient drill processing method using MQL and to verify its performance. To that end, the properties of Inconel that make it difficult -to -drill were studied by a comparison with the drilling of SM45C. Specific factors (i.e., cutting force and tool wear) were examined in relation to the conditions in the MQL-based drilling system. Based on these results, a sealed cover and step feed were proposed as measures to increase the effectiveness of the MQL system. The efficiency of the proposed method was established.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.40 no.4
• /
• pp.164-170
• /
• 2017

The CNC machine tool field is showing a growing trend with the recent rapid development of manufacturing industries such as semiconductors, automobiles, medical devices, various inspection and test equipment, mechanical metal processing equipment, aircraft, shipbuilding and electronic equipment. However, small and medium-sized machining companies that use CNC machine tools are experiencing difficulties in increasingly intense competition. Especially, small companies which are receiving orders from 3rd or 4th venders are very difficult in business management. In recent years, company S experienced difficulty to make product quality and delivery time due to the ignorance of the processing method when manufacturing cooling plate jig made of SUS304 material used for cell phone liquid crystal glass processing. In order to solve these problems, we redesigned the process according to the size of our company and tried to manage all processes with quantified data. In the meantime, we have found that there is a need to improve the cutter process, which accounts for most of the machining process. Therefore, we have investigated the correlation between RPM and FEED of three cutters that have been used in the past. As a result, we found that it is the most urgent problem to solve the roughing process during the cutter operation which occupies more than 70% of the total machining. In order to shorten the machining time and improve the quality in machining of SUS304 cooling plate jig, we select the main factors such as price, tool life, maintenance cost, productivity, quality, RPM, and FEED and use AHP to find the most suitable milling cutter. We also tried to solve the problem of delivery, quality and production capacity which was a big problem of S company through experiment operation with selected cutter tool. As a result, the following conclusions were drawn. First, the most efficient of the three cutters currently available in the machining center has proven to be an M-cutter. Second, although one additional facility was required, it was possible to produce the existing facilities without additional investment by supplementing the lack of production capacity due to productivity improvement. Third, the Company's difficulties in delivery and capacity shortfalls have been resolved. Fourth, annual sales increased by KRW 109 million and profits increased by KRW 32 million annually. Fifth, it can confirm the usefulness of AHP method in corporate decision making and it can be utilized in various facility investment and process improvement in the future.

• Journal of the Korean Society for Precision Engineering
• /
• v.26 no.5
• /
• pp.87-95
• /
• 2009

This research introduces the efficient modeling and manufacturing method using reverse engineering combined with rotational simulation of a pair of screw and mill-turn machining realized a proposed NC program. Because previously developed model had insufficient flow measuring accuracy, we considered that matter in the aspect of method of modeling and performance test. For that reason we modified the modeling which could minimize a gab between male and female screw, and developed precise tester which consists of constant tank, flowmeter and load cell, etc., and then conducted the test for defining characteristic and accuracy of flowmeter and repeated same test 5-times. Consequently we could obtain satisfied measuring accuracy and reproducibility indicated in the catalog of master model. Hence we give our conclusion as to the validity of developing accurate screw type flowmeter using the proposed process such as reverse engineering, mill-turn machining and precise performance test.