• Journal of Korea Multimedia Society
• /
• v.7 no.9
• /
• pp.1246-1254
• /
• 2004

This paper presents a image coding method that is well adaptive to close-range video transmission because of its low titrate and simple coding procedure. At first, it reduces temporal redundancies by performing image DPCM between previous frame and current frame, and makes wavelet transformed image of this difference image. Then, the coefficients are quantized selectively by using the coefficient values of base level and mid-frequency level because inter-level redundancies are widely exists in multi-resolution images. Finally quantized coefficients are made iron the function that implies the target bitrate, the average coefficient energy, and the value of the level. The proposed method shows the effective Performance in the experiments using the continuous motion images and transition images.

• Smart Structures and Systems
• /
• v.3 no.1
• /
• pp.23-49
• /
• 2007

Wavelet transforms are the emerging signal-processing tools for damage identification and time-frequency localization. A small perturbation in a static or dynamic displacement profile could be captured using multi-resolution technique of wavelet analysis. The paper presents the wavelet analysis of damaged linear structural elements using DB4 or BIOR6.8 family of wavelets. Starting with a localized reduction of EI at the mid-span of a simply supported beam, damage modeling is done for a typical steel and reinforced concrete beam element. Rotation and curvature mode shapes are found to be the improved indicators of damage and when these are coupled with wavelet analysis, a clear picture of damage singularity emerges. In the steel beam, the damage is modeled as a rotational spring and for an RC section, moment curvature relationship is used to compute the effective EI. Wavelet analysis is performed for these damage models for displacement, rotation and curvature mode shapes as well as static deformation profiles. It is shown that all the damage indicators like displacement, slope and curvature are magnified under higher modes. A localization scheme with arbitrary location of curvature nodes within a pseudo span is developed for steady state dynamic loads, such that curvature response and damages are maximized and the scheme is numerically tested and proved.

• Journal of the Korean Society for Precision Engineering
• /
• v.14 no.8
• /
• pp.130-136
• /
• 1997

For compensating the error motion of hydrostatic guideways, we introduce a way that the clearance of table is actively controlled corresponding to the amount of error with the variable capillary. The structure and the theoretical design method of active controlled capillary using piezo actuator, named ACC, are proposed in this paper. Basic characteristics such as the maximum controllable range, micro step response and available dynamic bandwidth are tested for confirmation of structural suitability of ACC, and these characteristics are also tested on the table mounted with ACC for verifying the availability. The experimental result showed that by the use of ACC, the error motion within 2.7 .mu. m of a hydrostatic guideway can be compensated with the resolution of 2.7nm, 1/100 contollable range, and the frequency bandwidth of 5.5 Hz. From these results, it is confirmed that the ACC is very effective to improve the motion accuracy of high or ultra precision hydrostatic guideways.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.29 no.3C
• /
• pp.387-397
• /
• 2004

The wavelet transform providing both of the frequency and spatial information of an image is proved to be very much effective for the compression of images, and recently lot of studies on coding algorithms for images decomposed by the wavelet transform together with the multi-resolution theory are going on. This paper proposes a quadtree decomposition method of image compression applied to the images decomposed by wavelet transform by using the correlations between pixels and '0'data grouping. Since the coefficients obtained by the wavelet transform have high correlations between scales and high concentrations, the quadtree method can reduce the data quantity effectively. the experimental infrared image with 256${\times}$256 size and 8〔bit〕, was used to compare the performances of the existing and the proposed compression methods.

• Transactions of Materials Processing
• /
• v.12 no.4
• /
• pp.277-283
• /
• 2003

In a closed-die forging process, blocker has been used to fill and distribute metal well in finisher die. Generally, the blocker shape was determined by an expert with many experiences. However, the manual blocker design process takes much time and efforts, so various automatic methods for the blocker design process have been suggested for the last three decades. The method with filtering in FFT (Fast Fourier Transform) for the blocker design provides general solution than other methods. But. due to the properties of FFT in time-frequency domain, this method has some drawbacks such as long calculation time, difficulty of local control and additional boundary process after filtering. In this study. DWT (Discrete Wavelet Transform), which is more flexible and is more wildly used than FFT, is applied to the blocker design. The method with filtering in DWT is very proper to design blocker in both 2-D and 3-D shapes. To verify the efficiency of this method, blockers of some models are designed and the results show that blocker design with DWT is effective for the blocker designs.

• Progress in Medical Physics
• /
• v.23 no.1
• /
• pp.26-32
• /
• 2012

The magnification technique has recently become popular in bone radiography, mammography and other diagnostic examination. However, because of the finite size of X-ray focal spot, the magnification influences various imaging properties with resolution, noise and contrast. The purpose of study is to investigate the influence of magnification and focal spot size on digital imaging system using eDQE (effective detective quantum efficiency). Effective DQE is a metric reflecting overall system response including focal spot blur, magnification, scatter and grid response. The adult chest phantom employed in the Food and Drug Administration (FDA) was used to derive eDQE from eMTF (effective modulation transfer function), eNPS (effective noise power spectrum), scatter fraction and transmission fraction. According to results, spatial frequencies that eMTF is 10% with the magnification factor of 1.2, 1.4, 1.6, 1.8 and 2.0 are 2.76, 2.21, 1.78, 1.49 and 1.26 lp/mm respectively using small focal spot. The spatial frequencies that eMTF is 10% with the magnification factor of 1.2, 1.4, 1.6, 1.8 and 2.0 are 2.21, 1.66, 1.25, 0.93 and 0.73 lp/mm respectively using large focal spot. The eMTFs and eDQEs decreases with increasing magnification factor. Although there are no significant differences with focal spot size on eDQE (0), the eDQEs drops more sharply with large focal spot than small focal spot. The magnification imaging can enlarge the small size lesion and improve the contrast due to decrease of effective noise and scatter with air-gap effect. The enlargement of the image size can be helpful for visual detection of small image. However, focal spot blurring caused by finite size of focal spot shows more significant impact on spatial resolution than the improvement of other metrics resulted by magnification effect. Based on these results, appropriate magnification factor and focal spot size should be established to perform magnification imaging with digital radiography system.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.11 no.3
• /
• pp.277-282
• /
• 2016

Effect of spectral drift in coherent fiber laser was investigated by injecting optical feedback to Fabry-Perot resonance loop. Er+3 doped fiber laser having unilateral optical feedback loop in Fabry-Perot configuration using two FBGs was fabricated. The optical feedback was found to be effective in linewidth reduction of fiber laser compared to the case without any optical feedback. The linewidth of three fiber lasers using above configuration were measured to be within 3kHz which is resolution-limited performance of self-heterodyne linewidth measurement set-up. The frequency drift measurement using Mach-Zehnder measurement set-up having 200m optical delay-line in one arm showed that the frequency drift rate of optical feedback fiber laser was measured as 300kHz/sec which was better than the case without optical feedback.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.20 no.1
• /
• pp.30-35
• /
• 2010

This paper presents a quality enhancement of images by using a histogram equalization based on the symmetric logistic function. The histogram equalization is a simple and effective spatial processing method that it enhances the quality by adjusting the brightness of image. The logistic function that is a sigmoidal nonlinear transformation function, is applied to non-linearly enhance the brightness of the image according to its intensity level frequency. We propose a flexible and symmetrical logistic function by only using the intensity with maximum frequency in an histogram and the total number of pixels. The proposed function decreases the computation load of an exponential function in the traditional logistic function. The proposed method has been applied for equalizing 5 images with a different resolution and histogram distribution. The experimental results show that the proposed method has the superior enhancement performances compared with the source images and the traditional global histogram equalization, respectively.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.19 no.6
• /
• pp.787-795
• /
• 2009

This paper presents a histogram equalization based on the logistic function for enhancing the quality of images. The histogram equalization is a simple and effective spatial processing method that it enhances the quality by adjusting the brightness of image. The logistic function that is a nonlinear transformation function is applied to adaptively enhance the brightness of the image according to its intensity level frequency. We propose a flexible and asymmetrical logistic function by only using the intensity level with maximum frequency and the maximum intensity level in an histogram, and the total number of pixels. The proposed function excludes both the computation load of an exponential function and the heuristic setting of an optimal parameter values in the traditional logistic function. The proposed method has been applied for equalizing many images with a different resolution and histogram distribution. The experimental results show that the proposed method has the superior enhancement performances and the faster equalizing speed compared with the traditional histogram equalization and the adaptively modified histogram equalization, respectively. And the proposed histogram equalization can be used in various multimedia systems in real-time.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2000.02a
• /
• pp.60-60
• /
• 2000

The adhesion interface formation between copper and poly(ethylene terephthalate)(PET), poly(methyl methacrylate)(PMMA) and Polyimide films was treated using Ion assisted reaction system to sequential sputter deposition by High-Frequency ion source. The ion beam modification system used a new type of low power HF ion thruster for space application as new low thruster electric propulsion system. Low power HF ion thruster with diameter 100mm gives the opportunity to obtain beams of Ar+ with currents 20~150 mA (current density 0.5~3.5 mA/cm2) and energy 200~2500eV at HF power level 10~150 W. Using Ar as a working gas it is possible to obtain thrust within 3~8 mN. Contact angles for untreated films were over 95$^{\circ}$ and 80 for Pet, 10o for PMMA and 12o for PI samples as a condition of ion assisted reaction at the ion dose of 10$\times$1016 ions/cm2, the ion beam potential of 1.2 keV and 4 ml/min for environmental gas flow rate. 900o peel tests yielded values of 15 to 35 for PET, 18 to 40 and 12 to 36 g/min. respectively. High resolution X-ray photoelectron spectrocopy is the Cls region for Cu metal on these polymer substrates showed increases in C=O-O groups for polymide, whereas PET and PMMA treated samples showed only C=O groups with increase the ion dose. Finally, unstable polymer surface can be changed from hydrophobic to hydrophilic formation such as C-O and C=O that were confirmed by the XPS analysis, conclusionally, the ion assisted reaction is very effective tools to attach reactive ion species to form functional groups on C-C bond chains of PET, PMMA and PI.