• Steel and Composite Structures
• /
• v.18 no.2
• /
• pp.345-355
• /
• 2015

In this study, the effects of weld parameters on nugget size and tensile-shear strength of welding joint in electrical resistance spot welding of galvanized DP 600 steel sheets having 1.2 mm were investigated. Taguchi design method has been employed to examine the effects of five parameters of welding current, electrode pressure, welding time, clamping time and holding time by using the $L_{27}(5^3)$ orthogonal array. Results showed that the most effective parameters on tensile shear strength and the nugget size ratio (hn/dn) were found as welding current and welding time, whereas electrode pressure, clamping time and holding time were less effective factors. Max. 545 MPa strength was obtained through proposed optimum conditions by Taguchi technique.

• Transactions of Materials Processing
• /
• v.16 no.5 s.95
• /
• pp.364-369
• /
• 2007

The effect of temperature on the forming limit diagram was investigated for AZ31B magnesium alloy sheet through the limit dome height test in the range from room temperature to $300^{\circ}C$. The formability of AZ31B sheet was improved significantly according to the increasing temperature. Also we studied the springback characteristics through the 2D draw bending test with different blank holding forces at elevated temperatures. Springback quantity was considerably reduced as temperature went up. The blank holding force in the range used, however, had little influence on springback. Experimental results obtained in this study may provide a material database for AZ31B sheet.

• Journal of the Korean Ceramic Society
• /
• v.29 no.7
• /
• pp.558-564
• /
• 1992

The effect of composed phase in the hot pressed CaO-MgO-Al2O3-SiO2 glass-ceramic has been investigated through microstructure studies, thermal, physical and mechanical properties. Sintering was done in the condition at the temperature range 900~95$0^{\circ}C$ for 20~120 mins under 7.5 MPa unilateral pressure. Sintered ceramics were composed of diopside, anorthite, residual glass and the portion of each phase was dependent on the sintering temperature and the holding time: as the temperature increases, the amount of diopside increased and then the rate of increase of diopside reduced with increasing anorthite. The thermal expansion coefficient of hot pressed was reduced with increasing crystallinity of hot pressed and was in the range of 6.69~7.46$\times$10-6 K-1 below $600^{\circ}C$. The elastic constant of hot pressed increased with increasing crystallinity up to about 80%, but after that was reduced due to the change of microstructure. The flexural strength of sintered ceramics was decreased with higher temperature and holding time, while the fracture toughness of those increased. It was shown that the physical and mechanical properties of hot pressed ceramic were related to the fraction of composed sintered ceramics, similar to a particulate composite, to the crystallinity of 80% of the glass-ceramic.

• Journal of the Korean Society for Heat Treatment
• /
• v.10 no.2
• /
• pp.128-137
• /
• 1997

The formation processes of the retained austenite(${\gamma}_R$) in SHCP100 steel sheets were investigated in order to improve the transformation induced plasticity(TRIP) effect of ${\gamma}_R$. An excellent combination of elongation about 23% and high strength over 830 MPa was achieved by processing of intercritical annealing and isothermal holding. The mechanical properties of TRIP-aided dual phase steel was found to depend on the volume ratio of each phase and the volume fraction of ${\gamma}_R$. It was also noted that the proper mechanical stability of ${\gamma}_R$ improved the mechanical properties. In this work, the best balance of strength-ductility was obtained by holding the steel at $420^{\circ}C$ for 500sec. after annealing at $730^{\circ}C$ for 300 sec.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.11a
• /
• pp.537-540
• /
• 1999

Effect of alignment layers on pretilt angle generation and electrical characteristics in nematic liquid crystal(NLC) by using photo-alignment techniques on polyimide (PI) surface with side chain were studied. The generated pretilt angle of the NLC on rubbed PI surface with 1-layer is almost the same as that of the 2-layers. However, the generated pretilt angle of the NLC on photo-induced PI surface with 2-layers is larger than that of the 1-layer. Therefore, the pretilt angle of the NLC on photo-induced PI surface is attributed to surface roughness due to photo-depolymerization of the polymer with UV light irradiation on PI surface. Next we observed the same characteristics of voltage-transmittance (V-T) and response time for 1- and 2-layers on PI surface. We also observed the same voltage holding ratio (VHR) characteristics for 1- and 2-layers on photo-aligned PI surface. Consequently, we suggest that the VHR of photo-aligned TN-LCD is higher than that of the rubbing-aligned TN-LCD.

• The Transactions of the Korean Institute of Electrical Engineers D
• /
• v.49 no.8
• /
• pp.459-466
• /
• 2000

In this paper, we propose an attitude controller for an unstructured object using CMG(Control Moment of Gyro) subsystem, which has a stabilizer function. The CMG subsystem consists of one motor for spinning the wheel and the other motor for turning the outer gimbal. While the wheel of CMG subsystem is spinning at high speed, applying force to the spin axis of the wheel leads the torque about the vertical axis. We utilize the torque to control the attitude of object in this study. For the stabilizer function, in additiion, holding the load at the current position, the power applied to the gimbal motor of CMG will be cut, which result in the braking force to stop the load by gyro effect. However, due to the gear reduction connected to outer gimbal, slow load motion cannot generate the braking force. Thus, in this study, we are willing to make a holding force by applying control power to the gimbal motor from the signal of piezoelectric gyroscopic sensor that detected the angular velocity of the load. These two features are demonstrated in experiment, carrying a beam with crane. As a result, load was started to rotate by controlling gimbal positiion and was stopped by turning off the gimbal power. Moreover, slow movement of the load was also rejected by additional control with gyroscopic sensor.

• Journal of the Korean Wood Science and Technology
• /
• v.39 no.4
• /
• pp.303-310
• /
• 2011

The mechanical properties of heat-compressed Radiata pine (Pinus radiata D.Don) by compression temperature and time were investigated. The compressive strength and bending strength of heat-compressed wood increased with increasing compression temperature and time. But the compressive strength and bending strength decreased with press temperature $220^{\circ}C$. It was considered due to thermal degradation during high temperature conditions. The surface hardness of heat-compressed wood increased with increasing compression temperature. However, the effect of compression time was negligible. The nail holding power was not affected by compression temperature and time.

• Journal of Life Science
• /
• v.7 no.4
• /
• pp.329-335
• /
• 1997

This study was conducted to investigate the effect of dietary fiber(DF) levels on the meat quality in colored broiler. Colored broiler were fed on containing corn-soy basal diet(DF 5%) and high level(DF 6,7 and 8%) of dietary fiber diets for 7 weeks. Dietary fiber level of diet was make up by adding some alffalfa meal. Colored broiler meats were stored at 3$\circ$ for 24hr after skaughter, and used to analyze physico-chemical properties. Proximate component, pH, shear force value, myofibril fragmentation index, water holding capacity, cooking loss, protein extractability, fatty acid composition, Hunter's L, a value and palatability of cooked meat were not significantly affected by dietary fiber levels, whereas the Hunter's value of meat was significantly affected bty dietary fiber levels for the final period of feeding. Crude protein content, myofibril fragmentation index, water holding capacity, protein extractability and Hunter's b value of breast meat's were higher than thigh meat's, but crude fat content, pH, shear force value, cooking loss, palmitoleic acid, linolenic acid, and Hunter's a value were lower, regardless of dietary fiber level.

• Journal of the Korean Society of Industry Convergence
• /
• v.24 no.5
• /
• pp.525-530
• /
• 2021

The purpose of this study was to investigate the effect of spherodizing heat treatment holding time on the microstructure and mechanical properties of the accelerated cooling-treated API X70 steel, which is mainly used as a structural material for line pipe steel for natural gas pipes. The accelerated cooling-treated API X70 steel was spherodizing treated at 700℃ for 12~48 h. The microstructure was observed using an OM and a FEG-SEM, and mechanical properties were obtained by tensile test. The microstructure of the API X70 steel was banded in the hot rolling direction, and the polygonal ferrite(PF) adjacent to pearlite(P) has mainly a fine size, and coarse PF and fine acicular ferrite were formed in the middle of P and P. As the spherodizing treatment time increased, the number of carbide particles decreased and its distribution interval increased, and the ferrite grain size was coarsened. The tensile strength decreased and the ductility increased with spherodizing treatment time, and the yield point elongation was disappeared in a stress-strain curve after the spherodizing treatment.

• Journal of Welding and Joining
• /
• v.30 no.6
• /
• pp.106-112
• /
• 2012

This study was carried out to investigate the effect of bonding temperature and holding time on microstructure and mechanical properties in brazing joints of Ni-base superalloy using MBF-30 (Ni-4.5Si-3.2B [wt.%]). The heating rate was $20^{\circ}C$/min to the bonding temperatures $1050^{\circ}C$, $1070^{\circ}C$, $1090^{\circ}C$ under high vacuum condition. The holding times were 100s, 400s, 900s and 1600s. $Ni_3B$ phases and proeutectic Ni were observed in the interlayer of Ni-201. Then, Ni3B and Ni3Si were found in the middle region of brazing joint. Cr-boride phase appeared in the interlayer of Inconel-625. Tensile strength and elongation were decreased at $1050^{\circ}C$-1600s, $1070^{\circ}C$-900s and $1090^{\circ}C$-400s. After observation the fracture specimens, There was Ni3B which is very brittle phase in the grain boundary of Ni201.