• Structural Engineering and Mechanics
• /
• 제90권2호
• /
• pp.177-187
• /
• 2024

In this study, compared two distinct estimation methods (stress charts and regression equations) proposed by the Indian road congress design guideline (IRC:58-2015) to determine flexural stress in Jointed Plain Concrete Pavement (JPCP). The occurrence of critical flexural stresses in pavement slabs is due to the combined effects of wheel loads and temperature. These stresses depend on various factors such as material properties of concrete, soil-subgrade strength, loading, and geometric properties of the slab. In order to account for the practical variability of these factors, critical edge stresses are determined using both methods and compared considering tied concrete shoulder. IRC:58 (2015) suggests, the stresses calculated by both the procedures should provide the same results. However, when these stresses are compared for the same configurations and same loading conditions, large variations are observed. The effect of tied concrete shoulder on reduction in critical edge stress is observed. Based on the study, certain important conclusions and recommendations are presented.

• 대한치과보철학회지
• /
• 제35권4호
• /
• pp.742-766
• /
• 1997

The purpose of this study was to determine the effect of finish line design, amount of incisal reduction, and loading condition on the stress distribution in anterior all-ceramic crowns. Three-dimensional finite element models of an incisor all-ceramic crown with 3 different finish line designs : 1) shoulder with sharp line angle 2) shoulder with rounded line angle 3) chamfer : and 2 different incisal reductions : 2mm and 4mm were developed. 300 N force with the direction of 45 degree to the long axis of the tooth was applied at 3 different positions : A) incisal 1/3, B) incisal edge, C) cervical 1/5. Stresses developed in ceramic and cement were analyzed using three-dimensional finite element method. The results were as follows : 1. Stresses were concentrated in the margin region, which were primarily compressive in the labial and tensile in the lingual. 2. Stresses were larger in the area near line angle than on the crown surface of the margin region. In case of shoulder with sharp line angle, stresses were highly concentrated in the porcelain near line angle. 3. At the interface between porcelain and cement and at the porcelain above the margin on crown surface, stresses were the highest in chamfer, and decreased in shoulder with sharp line angle and shoulder with rounded line angle, respectively. 4. At the interface between cement and abutment on crown surface, stresses were the highest in shoulder with sharp line angle, and decreased in shoulder with rounded line angle and chamfer, respectively. 5. The amount of incisal reduction had little influence on the stress distribution in all-ceramic crowns. 6. When load was applied at the incisal edge, higher stresses were developed in the margin region and the incisal edge than under the other loading conditions. 7. When load was applied at the cervical 1/5, stresses were very low as a whole.

• Structural Engineering and Mechanics
• /
• 제68권4호
• /
• pp.497-505
• /
• 2018

Three points bending flexural test was modeled numerically to study the crack propagation in the pre-cracked beams. The pre-existing edge cracks in the beam models were considered to investigate the crack propagation and coalescence paths within the modeled samples. The effects of particle size on the single edge-notched round bar in bending test were considered too. The results show that Failure pattern is constant by increasing the ball diameter. Tensile cracks are dominant mode of failure. These crack initiates from notch tip, propagate parallel to loading axis and coalescence with upper model boundary. Number of cracks increase by decreasing the ball diameter. Also, tensile fracture toughness was decreased with increasing the particle size. In the present study, the influences of particles sizes on the cracks propagations and coalescences in the brittle materials such as rocks and concretes are numerically analyzed by using a three dimensional particle flow code (PFC3D). These analyses improve the understanding of the stability of rocks and concretes structures such as rock slopes, tunnel constructions and underground openings.

• Smart Structures and Systems
• /
• 제22권6호
• /
• pp.663-673
• /
• 2018

In this study, the effect of particle size on the cracks propagation and coalescence or cracking pattern of the edge notched disc specimens are investigated. Firstly, calibration of PFC3D was performed using Brazilian experimental test output. Then micro parameters were used to build edge notched disc specimen. The horizontal wall of the assembly is let to move downward with a standard low speed of 0.016 m/s. The numerical results show that the tensile cracks are dominant failure pattern for the modeled discs. These tensile cracks initiate from the pre-existing notch tip and propagate parallel to the loading direction then interact with the upper boundary of the modeled specimen. As the size of the balls (ball diameter) decrease the number of tensile cracks increase. The tensile fracture toughness of the samples also decreases as the particle size increases. Understanding the crack propagation and crack coalescence phenomena in brittle materials such as concretes and rocks is of paramount importance in the stability analyses for engineering structures such as rock slopes, underground structures and tunneling.

• 대한조선학회논문집
• /
• 제28권2호
• /
• pp.40-51
• /
• 1991

캐비테이션 특성이 우수하고 추진효율이 높은 콘테이너선용 프로펠러를 설계하기 위하여 새로운 날개단면(KH18)을 이용한 프로펠러 설계법을 제안하였다. KH18 단면은 캐비테이션 초생곡선(Cavitation-free bucket diagram) 및 양력-항력곡선(Lift-drag curve)에서 폭이 넓어 불균일한 선미후류에서 작동되는 선박용 프로펠러의 날개 단면으로 적당하리라 판단되었다. 새로운 날개 단면을 이용한 콘테이너선의 프로펠러 설계를 위하여 양력면이론을 사용하였다. 프로펠러 설계시 코오드 방향 부하분포를 설계변수로 선택하여 5개의 프로펠러를 설계하였고, 단면 변화의 영향을 비교하기 위하여 NACA형 단면을 갖는 프로펠를 설계하여 예인수조 및 캐비테이션 터널에서 모형시험을 수행하였다. 모형시험 결과 코오드 방향 부하분포가 프로펠러 반경의 70% 내부에서는 날개 앞날의 부하가 적고 그 외부에서는 날개 앞날부하가 상대적으로 큰 코오드방향 부하분포를 갖는 프로펠러(KP197)가 NACA 단면을 갖는 프로펠러에 비하여 추진효율은 1% 향상되었고 캐비테이션 발생양은 30% 감소하였으며 선체변동압력은 9%감소하였다. 새로운 날개단면을 갖는 프로펠러의 캐비테이션 특성이 우수함을 고려하여 낱개 전개면적비를 감소시킨다면 더 많은 추진효율 증가를 기대할 수 있으리라 판단된다.

• International Journal of Internet, Broadcasting and Communication
• /
• 제11권3호
• /
• pp.8-19
• /
• 2019

Since their emergence in 2007, smart phones have advanced up to the point that 5G mobile communication in 2019 started to be commercialized. Accordingly, now it is possible to share 3D modeling files and collaborate by means of a mobile web. As the recently commercialized 5G mobile communication network is so useful in sharing 3D modeling files and collaborating that even large-size geometry files can be transmitted at ultra high speed with ultra low transfer delay. We examines characteristics of major 3D file formats such as STL, OBJ, FBX, and glTF and compares the existing 4G LTE (Long Term Evolution) network with the 5G NR (New Radio) mobile communication network. The loading time and packets of each format were measured depending on the mobile web browser environments. We shows that in comparison with 4G LTE, the loading time of STL and OBJ file formats were reduced as much as 6.55 sec and 9.41 sec, respectively in the 5G NR and Chrome browsers. The glTF file format showed the most efficient performance in all of the 4G/5G mobile communication networks, Chrome, and Edge browsers. In the case of STL and OBJ, the traffic was relatively excessive in 5G NR and Edge browsers. The findings of this study are expected to be utilized to develop a 3D file format that reduces the loading time in a mobile web environment.

• 유체기계공업학회:학술대회논문집
• /
• 유체기계공업학회 2002년도 유체기계 연구개발 발표회 논문집
• /
• pp.131-136
• /
• 2002

A computational analysis using Reynolds stress model in FLUENT is conducted to give a clear understanding of the effect of blade loading on the structure of tip leakage flow in a forward-swept axial-flow fan at design condition ($\phi$=0.25) and off-design condition ($\phi$=0.21 and 0.30). The roll-up of tip leakage flow starts near the minimum static wall pressure position, and the tip leakage vortex developes along the centerline of the pressure trough within the blade passages. Near tip region, a reverse flow induced by tip leakage vortex has a blockage effect on the through-flow. As a result, high momentum region is observed below the tip leakage vortex. As the blade loading increases, the reverse flow region is more inclined toward circumferential direction and the onset position of the rolling-up of tip leakage flow moves upstream. Because the casing boundary layer becomes thicker, and the mixing between the through-flow and the leakage jet with the different flow direction is enforced, the streamwise vorticity decays more fast with blade loading increasing. The computational results show that a distinct tip leakage vortex is observed downstream of the blade trailing edge at $\phi$=0.30, but it is not observed at $\phi$=0.21 and 0.25.

• 한국구조물진단유지관리공학회 논문집
• /
• 제20권1호
• /
• pp.41-47
• /
• 2016

본 연구에서는 콘크리트에 표면매입된 FRP판의 부착거동에서, 전단키와 연단거리의 효과를 관찰하기 위한 부착시험을 실시하였다. 실험에서의 주요변수는 전단키의 위치, 형태 그리고 연단길이이다. 규격 $3.6mm{\times}16mm$의 FRP를 $400mm{\times}200(300)mm{\times}400mm$ 규격의 콘크리트 블록에 매입하고 에폭시로 고정시켜서 실험변수에 따라 총 10개의 부착실험체를 제작하였다. FRP의 연단에 인장력을 가한 뒤 파괴시까지 실험을 실시하고 하중을 기록하였으며, 미끄러짐과 FRP의 인장변형량을 기록하였다. 실험으로부터, 전단키의 위치는 가력부에서 멀리 떨어질수록 전단강도가 상승하는 것으로 나타났으며, 전단키의 직경이 커질수록 내력이 저하되는 것으로 나타났다. 특히 전단키가 일정 이상의 규격이 되면 전단키가 없는 경우에 비하여 내력이 저하되어 오히려 부착강도에 부정적인 영향을 미칠 수 있는 것으로 나타났다. NSM FRP에서 응력장용방향의 연단거리가 길어짐에 따라 동일 부착길이임에도 불구하고 내력이 일부 증가하는 것으로 나타났다. 표면매입 보강된 FRP의 부착실험에서, FRP와 콘크리트사이의 부착-미끄러짐은 전체거동을 지배하는 것으로 나타나므로 이에 따른 과도한 미끄러짐은 설계에 반드시 고려될 필요가 있다.

• 한국도로학회논문집
• /
• 제10권2호
• /
• pp.183-191
• /
• 2008

본 연구에서는 아스팔트 혼합물의 변형강도시험에서 하중봉의 치수가 변형강도 특성에 미치는 영향을 평가하였다. 이를 위하여 직경(D) 40mm, 하단의 원형 절삭 반경(r)을 10.0mm와 10.5mm로 제작한 두 개의 하중봉으로 아스팔트 혼합물의 변형강도를 측정하고, 반복주행시험을 수행하여 얻어진 소성변형 특성치와 상관성 분석을 하였다. 또한 하중봉의 원형 절삭반경에 따른 골재치수에 어떠한 영향을 미치는지를 확인하기 위하여 통계 분석을 하였다. 변형강도 값과 변동계수는 r=10mm하중봉을 사용한 것이 더 낮은 것으로 나타났다. 또한 r=10mm 하중봉이 변형강도와 소성변형 특성치와 상관성 분석에서도 더 높은 상관성을 보였다. 골재치수와 원형 절삭반경은 변형강도에 영향을 미치는 것으로 나타났으나 두 변수의 교호작용에서는 골재의 크기가 $10mm{\sim}19mm$내에서는 r에 영향을 받지 않는 것으로 나타났다. 따라서 소성변형과의 상관성이 더 우수하며 변동계수도 낮은 것으로 나타난 D=40mm, r=10.0mm의 하중봉을 사용하는 것이 적합할 것으로 판단되었다.

• Journal of Biosystems Engineering
• /
• 제30권6호통권113호
• /
• pp.366-372
• /
• 2005

The objective of this study was to evaluate the bump crossing and loading stability of a proto-type mini-forwarder under development. The evaluation was performed by computer simulation using a multi-body dynamic analysis program, Recur- Dyn 5.21. The proto-type was modeled and its properties such as mass, mass center, and mass moment of inertia were determined using 3D CAD modeler, Solid Edge 8.0. The $\%$ errors of masses, mass center, mass moment of inertia, and vertical motion of the model were within less than $10\%$ and the model's behavior agreed relatively well with those of the proto-type when traversing over a rectangular bump. Using the validated model, bump crossing of the proto-type was simulated and the loading limit was determined. It was found that effects of the shapes of bump on the bump crossing performance was insignificant within the practical heights of bumps. Stability of bump crossing increased with loading. However, loading of longer logs than 2.7 m made the crossing unstable because the ends of logs contacted ground when traversing over the bump. The maximum loading capacity of the proto-type was estimated to be 7.8 kN of 2.7 m long logs.