• Proceedings of the Korea Concrete Institute Conference
• /
• 2006.05b
• /
• pp.101-104
• /
• 2006

This study aims to obtain technical data for improvement of utilization of Blast Furnace Slag(BFS), recycled aggregate in the future by complementing fundamental problems of BFS such as manifestation of initial strength and excessive alkali quantity as well as weakness of recycled fine aggregate through manufacturing of recycled fine aggregate mortar using BFS. Since hydroxide ion concentration of calcium hydroxide(Ca(OH)2) ion erupted from recycled fine aggregate newly produced is over 12. In recycled fine aggregate mortar transposing and using BFS powder, calcium hydroxide(Ca(OH)2) erupted from recycled fine aggregate played a role of stimulus from the day 3 and manifestation of compressive strength was slowly increased with mortar using natural fine aggregate and showed considerable increase from the day 7.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2006.05b
• /
• pp.5-8
• /
• 2006

In this study, various fundamental experiments including durability and time-dependent deformation are performed to compile a database for a utilization of high-strength concrete for PSC bridges. In the mix design, concrete strength at early age when prestressing forces are introduced to the PSC member and slumpflow suitable for pumping of concrete are considered to make a concrete fit for PSC bridges. The main parameters investigated are the kinds and replacement ratios of mineral admixtures and low-heat cement. Experimental tests on durability include penetration of chloride ions, freezing-thawing, combined deterioration, and simple adiabatic temperature rise test. In addition, time-dependent deformation such as creep, drying and autogenous shrinkage, which is particularly important factor in the design and construction of PSC bridges, is tested and analyzed.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2018.05a
• /
• pp.275-276
• /
• 2018

Ultra high performance concrete(UHPC) represents high early age autogenous shrinkage strain due to its low water-to-binder ratio(W/B) and high fineness admixture usage. It has been reported that fiber can control restrained tensile stress and crack. The purpose of the present study is, therefore, to investigate the autogenous shrinkage as well as mechanical properties including compressive strength, flexural strength and modulus of elasticity on the UHPC with fiber type and pre-mix of binder.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2004.11a
• /
• pp.137-140
• /
• 2004

Hydraulic structures have been constructed with low cost concrete so as to increase the investment efficiency. As the construction of agricultural irrigation and drainage project is concentrated on off-farming season and come to construction less than 28-day strength in quality control. As we are aware the major thrust construction of short period is now in hydraulic structures rather then the large- scale. This paper will propose the relationship between the 7-day and 28-day compressive strength of concrete be investigated. Test will be carried out on nine different concrete mixes and 180 core drilled form the hydraulic structures with 7-day and 28-day compressive strengths ranging approximately from 24 to 30Mpa.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2006.11a
• /
• pp.773-776
• /
• 2006

This experimental study is the fundamental report to use the ternary concrete. This study performed to know physical properties of ternary concrete according to replacement ratio of pozzolanic admixtures and curing temperature conjugation. To investigate Strength development properties of according to replacement ratio of pozzolanic admixtures, both fly ash replaced on portland cement in 5, 10 and 15% weight ratios and blast furnace slag replaced on the portland cement in 5, 15, 20, 30 and 40% weigt ratios was used. Also this is studied fresh and hardened concrete properties in condition of curing temperature $10^{\circ}C\;and\;20^{\circ}C$. The followings are the summary of which concluded in this study. Considering the concrete cured over 28 days compressive strength, most replacement ratios of pozzolanic admixtures were higher than plain concrete that. Compressive strength development properties of ternary concrete according to curing temperature conjugation were similar except for early age.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2020.06a
• /
• pp.58-59
• /
• 2020

The change of temperature and humidity in early-age concrete has a great influence on the durability of the structure. In this study, a reliable wireless sensor network system and a concrete embedded type Compressive strength prediction sensor were designed using the Arduino platform. The accuracy of the compressive strength prediction sensor was verified through a mock-up experiment, and it was confirmed that the experiment had sufficient accuracy to be used in the field environment.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2006.05a
• /
• pp.147-153
• /
• 2006

Photocatalyst reaction has limit of its usage because application range mostly centered on atmosphere purification area. Thus, it is true that an alternative plans are necessary to increase usage of $TiO_2$ as photocatalyst material. (1) The result of flow felt according to $TiO_2$ replacement rate has shown that both of anatase type and rutile type over 12% deviated from desired flow, $110{\pm}5mm$. Consequently, the range below 9% will be suitable when the anatase type $TiO_2$ if used for functional additives if workability is considered. (2) After compressive strength test, replacement rate 6-9% is estimated as suitable range if $TiO_2$ is used as compressive strength material. Rutile type and anatase type are suitable for in early-age strength and long-age strength respectively. (3) It was revealed that bending strength was dramatically decreased when replacement rate was increased. The main reason were the increase of $TiO_2$ doesn't influence hydration reaction and the decrease of bending strength. (4) The result from the water purification properties test using ion-chromatograhpy has shown that the condition with anatase type $TiO_2$ was normally better than rutile type on the same replacement rate.

• Journal of the Korea Institute of Building Construction
• /
• v.16 no.1
• /
• pp.53-58
• /
• 2016

In order to investigate the feasibility of municipal solid waste incineration ash melted slag powder as admixture, an experimental study was performed on cement mortar with municipal solid waste incineration ash melted slag powder. Fresh mortar properties and strength properties with various municipal solid waste incineration ash melted slag powder replacement ratios were estimated. There replacement ratio adopted in this study was 0, 10, 20, 30, 40, 50%. After then flow properties was considered as properties of fresh mortar. And compressive strength was determined 3, 7, 14, 28, 56 days for the hardened mortar specimens. According to the test results, the flow of mortar was increased with in replacement amount of municipal solid waste incineration ash melted slag powder. Furthermore, compressive strength at early age was decreased, whereas the compressive strength at the age of 28, 56day was increased.

• Korean Journal of Materials Research
• /
• v.21 no.9
• /
• pp.502-508
• /
• 2011

The goal of the present work was to investigate the development of a geopolymeric ceramic material from a mixture of mine residue, coal fly ash, blast furnace slag, and alkali activator solution by the geopolymer technique. The results showed that the higher compressive strength of geopolymeric ceramic material increased with an increase in active filler (blast furnace slag + coal fly ash) contents and with a reduction of mine residue contents. The geopolymeric ceramic had very high early age strength. The compressive strength of the geopolymeric ceramic depended on the added active filler content. The maximum compressive strength of the geopolymeric ceramic containing 20 wt.% mine residue was 141.2 MPa. The compressive strength of geopolymeric ceramic manufactured by adding mine residue was higher than that of portland cement mortar, which is 60 MPa, when cured for 28 days. SEM observation showed the possibility of having amorphous aluminosilicate gel within geopolymeric ceramic. XRD patterns indicate that the geopolymeric ceramic was composed of amorphous aluminosilicate, calcite, quartz, and muscovite. The Korea Standard Leaching Test (KSLT) was used to determine the leaching potential of the geopolymeric ceramic. The amounts of heavy metals were noticeably reduced after the solidification of mine residue with active filler.

• Journal of the Korean Society of Industry Convergence
• /
• v.8 no.3
• /
• pp.169-176
• /
• 2005

The purpose of this study is to develop the high strength crushed sand concrete in conditions of water binder ratios of 25, 30, 35% and blast-furnace slag substitutions of 0, 15, 30, 45%. Additionally, in case of water binder ratio of 30%, the maximum size of coarse aggregate is two kinds of 13, 19 mm. The conclusions of this study are as follows ; 1. The compressive strength appeared lower in early age as compared with that of plain concrete according to increasing of the blast-furnace slag substitution. But, the compressive strength was respectively 5, 6, 10% larger than that of plain concrete in case of 25, 30, 35% water binder ratios, 28 days, 30% blast-furnace slag substitution and 19mm coarse aggregate. 2. According to increasing of the blast-furnace slag substitution, the modulus of elasticity and the tensile strength of concrete increased. 3. The length change by the shrinkage increased when the larger coarse aggregate was used, and decreased according to higher blast-furnace slag substitution.