• Journal of the Korean Society of Food Science and Nutrition
• /
• v.44 no.11
• /
• pp.1693-1699
• /
• 2015

Overall quality of six kinds of commercial broiler breast fillets (A~F) retailed in Korea were examined, including proximate composition analysis, shape profile analysis, pH, color, tenderness, cooking loss, descriptive analysis, and consumer testing. A total of 120 breast meat fillets were purchased at a local market. Overall quality of broiler breast meat commercially available in Korea was found to vary significantly, indicating a broad range of product quality in the marketplace. Moisture content of meat ranged from 74.4 to 76.4%, whereas protein, fat, and ash contents were 21.8~25.2, 0.2~0.8, and 1.07~1.16%, respectively. The pH ranged from 6.2 to 6.4, whereas color values ($L^*$, $a^*$, and $b^*$) were 52.2~57.2, -3.5~0.5, and 8.3~13.6, respectively, among all products tested. Approximately 9% variation in cooking loss was detected depending on the products evaluated, whereas shapes (height, width, and length) of meat were also significantly different (15% variation on average). Product F was proven to be the least tender and least liked by consumers, implying that tenderness is a key attribute determining consumer acceptability of broiler breast meat.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.2 no.1
• /
• pp.120-127
• /
• 2006

The hammer-milled characteristics of waste wood materials such as lumber, plywood, particleboard(PB), MDF and railroad tic were investigated in this study. The physical and mechanical properties of recycled boards according to types of recycled particle and the mixing ratios were also studied. The hammer-milled, waste wood materials had the dimensional distributions suitable for the core layer panicle. Bending strengths of recycled boards (one layer) were shown in order of plywood, PB(laboratory-fabricated with particles used in the PB factory), lumber, tego film-overlaid plywood, MDF, waste railroad tie, PB(factory-made) and LPL-overlaid PB. Cured resin and creosote containing waste wood contributed to dimensional stability of reconstituted boards. Considering the mixing effects between lumber and plywood with recycled PB particle, lumber particle was contributive to bending strength, MOE and internal bond(IB) strength, whereas plywood particle was contributive to dimensional stability. The bending and IB strength of 3 layer boards composing only recycled waste wood particles in core layer of board were in order of lumber, plywood, PB and MDF. On the other hand, the thickness swelling was in order of PB, lumber, plywood and MDF. Bending strength of the 3 layer boards mixed with recycled PB-particle in the core layer had a decreasing tendency, as the mixing ratios of recycled PB-particles increased. The dimensional stability of 3 layer recycled board was improved as the mixing ratio of recycled PB-particle increased same as in one layer. Formaldehyde emission of boards fabricated with recycled PB-particles in the core layer of the PB was in the range of E2 grade (below 5.0mg/l).

• Journal of the Korean Electrochemical Society
• /
• v.3 no.3
• /
• pp.136-140
• /
• 2000

A stainless steel separator for a molten carbonate fuel cell is usually coated with aluminum diffusive layer to protect its surface against corrosion by the molten carbonate at high temperatures. In this study, a relatively simple method was devised to form the aluminum diffusive layer on a stainless steel substrate. Slurry coating of aluminum on the substrate followed by heat treatment under reducing atmosphere at $650\~800^{\circ}C$ produced the aluminum diffusive layer of $25\~80{\mu}m$ thickness. The thickness of aluminum diffusive layer increased with increasing the temperature or duration of the heat-treatment. The corrosion resistance against molten carbonate under oxidizing atmosphere was significantly improved by aluminum diffusive layer formed by the sluny painting and heat treatment method. Moreover, the sample prepared in this study showed corrosion behavior similar to the sample with aluminum diffusive layer prepared by ion vapor deposition and heat treatment.

• Journal of the Korean Ceramic Society
• /
• v.38 no.12
• /
• pp.1155-1161
• /
• 2001

Yittrium Iron Garnet(YIG) has been used as an important material in the circulator/isolator which is used in RF communication system, mobile phone, adn satellite broadcasting, etc. In this study, we investigated the microstructural and magnetic properties of YIG ferrites with the sintering temperature and additives. We fabricated the YIG ferrites substituted with Ca, In, V by the traditional ceramic sintering method at 1250$\^{C}$, 1275$\^{C}$, 1300$\^{C}$ and 1325$\^{C}$. Powders were granulated by using a spray dryer. Crystallographic and microstructural properties were measured by using XRD and SEM. Magnetic properties were measured by using a VSM for saturation magnetization (4$\pi$M$\_$s/) and FMR (Ferromagnetic Resonance) experiment for ferromagnetic resonance line width (△H). The YIG ferrite, Y$\_$1.6/Ca$\_$1.4/Fe$_4$V$\_$0.7/In$\_$0.3/O$\_$12/, sintered at 1300$\^{C}$, showed higher saturation magnetization and lower ferromagnetic resonance line width than any other sintering temperatures.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.34 no.7
• /
• pp.1035-1040
• /
• 2005

This study was conducted to investigate the surface spraying effect of materials on the rheological properties of frozen starch with microwave heating. Microwave helps reduce cooking time by high temperature, but swiftly snatches moisture from foods such as frozen starches (buns and noodles etc) and makes surface of foods harder. Four types of maltodextrin materials have been prepared for different concentration solutions and sprayed on surface doughs of sheet type. Sprayed dough samples were Quickly frozen at $-70^{\circ}C$ and wrapped with polypropylene film. All the treated samples were kept at 0, -20 and $-50^{\circ}C$, and then taken out periodically for measurement of the quality during storage. The quality attributes evaluated after heating with microwave energy include sensory quality retrogradation, texture, surface color and microstructure. The quality of frozen starches deteriorated with long term storage even at low temperatures of -20 and $-50^{\circ}C$, and the spray materials were found to improve the textural and physical properties of frozen starches in the microwave heating. Particularly, maltodextrin with D.E value of $9\~12$ had the most desirable effects of quality improvement.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.236-236
• /
• 2008

(Bi,La)$Ti_3O_{12}$(BLT) thin film is one of the most attractive materials for ferroelectric random access memory (FRAM) applications due to its some excellent properties such as high fatigue endurance, low processing temperature, and large remanent polarization [1-2]. The authors firstly investigated and reported the damascene process of chemical mechanical polishing (CMP) for BLT thin film capacitor on behalf of plasma etching process for fabrication of FRAM [3]. CMP process could prepare the BLT capacitors with the superior process efficiency to the plasma etching process without the well-known problems such as plasma damages and sloped sidewall, which was enough to apply to the fabrication of FRAM [2]. BLT-CMP characteristics showed the typical oxide-CMP characteristics which were related in both pressure and velocity according to Preston's equation and Hernandez's power law [2-4]. Good surface roughness was also obtained for the densification of multilevel memory structure by CMP process [3]. The well prepared BLT capacitors fabricated by CMP process should have the sufficient ferroelectric properties for FRAM; therefore, in this study the electrical properties of the BLT capacitor fabricated by CMP process were analyzed with the process parameters. Especially, the effects of CMP pressure, which had mainly affected the removal rate of BLT thin films [2], on the electrical properties were investigated. In order to check the influences of the pressure in eMP process on the ferroelectric properties of BLT thin films, the electrical test of the BLT capacitors was performed. The polarization-voltage (P-V) characteristics show a decreased the remanent polarization (Pr) value when CMP process was performed with the high pressure. The shape of the hysteresis loop is close to typical loop of BLT thin films in case of the specimen after CMP process with the pressures of 4.9 kPa; however, the shape of the hysteresis loop is not saturated due to high leakage current caused by structural and/or chemical damages in case of the specimen after CMP process with the pressures of 29.4 kPa. The leakage current density obtained with positive bias is one order lower than that with negative bias in case of 29.4 kPa, which was one or two order higher than in case of 4.9 kPa. The high pressure condition was not suitable for the damascene process of BLT thin films due to the defects in electrical properties although the better efficiency of process. by higher removal rate of BLT thin films was obtained with the high pressure of 29.4 kPa in the previous study [2].

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.20-20
• /
• 2008

최근 LEDs가 동일 효율의 전구에 비해 에너지 절감 효과 크며 신뢰성이 뛰어나다기 때문에 기존 광원을 빠르게 대체해 나가고 있다. 특히 자외선 파장을 가지는 LEDs는 발열이 낮아 냉각장치가 필요 없으며, 수명이 길어 기존 UV lamp에 비해 많은 장점을 가지고 있기 때문에 많은 관심을 밭고 있다. 그럼에도 불구하고 자외선 LEDs는 제조 단가가 높고 power가 낮아 소요량이 많은 등 아직 해결해야 할 부분이 많기 때문에 이를 해결하기 위해 여러가지 재료와 다양한 구조가 고려되고 있다. 그 중 ZnO는 II-VI족 화합물 반도체로써 UV영역의 넓은 밴드갭(3.37eV)을 가지는 투명한 재료이다. 특히 ZnO는 60meV의 큰 엑시톤 결합에너지를 가지며, 가시광 영역에서 높은 투과율을 가지고, 상온에서 물리적, 화학적으로 안정하기 때문에 UV sensor, UV laser, UV converter, UV LEDs 등 광소자 분야에서 연구가 활발히 진행되고 있다. ZnO가 광소자의 발광재료로써 높은 효율을 얻기 위해서는 결정성을 높여 내부 결함을 감소시키며, 발광 면적을 높일 수 있는 구조가 요구된다. 특히 MOCVD 법으로 성장한 나노막대는 에피성장되어 높은 결정성을 기대할 수 있으며, 성장 조건을 조절함으로써 나노막대의 aspect ratio와 밀도 제어할 수 있기 때문에 표면적을 효과적으로 넓혀 높은 발광효율을 얻을 수 있다. 본 실험에서는 MOCVD 법으로 실리콘과 사파이어 기판 위에 다양한 성장 온도를 가진 나노구조를 성장 시키고 온도에 따른 형상 변화와 특성을 평가하였다. ZnO 의 성장온도가 약 $360^{\circ}C$ 일 때, 밀도가 조밀하고 기판에 수직 배열한 균일한 나노막대가 성장되었으며 우수한 결정성, 광학적 특성이 나타남을 SEM, TEM, PL, XRD를 사용하여 확인하였다.

• Electrical & Electronic Materials
• /
• v.7 no.4
• /
• pp.317-324
• /
• 1994

In this study, new preparation method of LiCoO$_{2}$ was applied to develop cathode active material for Li rechargeable cell, and followed by X-ray diffraction analysis, electrochemical properties and initial charge/discharge characteristics as function of current density. HC8A72- and CC9A24-LiCoO$_{2}$ were prepared by heating treatment of the mixture of LiOH H$_{2}$O/CoCO$_{3}$(1:1 mole ratio) and the mixture of Li$_{2}$CO$_{3}$/CoCO$_{3}$(1:2 mole ratio) at 850 and 900.deg. C, respectively. Two prepared LiCoO$_{2}$s were identified as same structure by X-ray diffraction analysis. a and c lattice constant were 2.816.angs. and 14.046.angs., respectively. The electrochemical potential of CFM-LiCoO$_{2}$(Cyprus Foote Mineral Co.'s product), HC8A72-LiCoO$_{2}$ and CC9A24 LiCoO$_{2}$ electrode were approximately between 3.32V and 3.42V vs. Li/Li reference electrode. Stable cycling behavior was obtained during the cyclic voltammetry of LiCoO$_{2}$ electrode. According as scan rate increases, cathodic capacity decreases, but redox coulombic efficiency was about 100% at potential range between 3.6V and 4.2V vs. Li/Li reference electrode. Cathodic capacity of HC8A72-LiCoO$_{2}$ was 32% higher than that of CFM-LiCoO$_{2}$ and that of CC9A24-LiCoO$_{2}$ was 47% lower than that of CFM-LiCoO$_{2}$ at 130th cycle in the condition of lmV/sec scan rate. Constant cur-rent charge/discharge characteristics of LiCoO$_{2}$/Li cell showed increasing Ah efficiency with initial charge/discharge cycle. Specific discharge capacities of CFM and HC8A72-LiCoO$_{2}$ cathode active materials were about 93mAh/g correspondent to 34% of theretical value, 110mAh/g correspondent to 40% of theretical value, respectively. In the view of reversibility, HC8A72-LiCoO$_{2}$ was also more excellent than CFM- and CC9A24-LiCoO$_{2}$.

• Journal of the Korean Chemical Society
• /
• v.48 no.3
• /
• pp.266-272
• /
• 2004

We developed a miniaturized solid-state carbonate ion-selective electrode (carbonate ISE) based on one-component room temperature vulcanizing type silicone rubber 730 (730 RTV) without adding plasticizer to the matrix. The optimized carbonate ion selective membrane is prepared with 85.8 wt% of 730 RTV, 11.1 wt% of trifluoroacetyl-p-decylbenzene (TFADB), and 3.1 wt% of tridodecyl-methylammonium chloride (TDMACl). This carbonate ISE exhibited excellent potentiometric properties (i.e., slope: 26.3 mV/dec; selectivity: $logKT^{pot}_{CO_{2},Cl^-}$= -4.00 and $logKT^{pot}_{TCO_{2},Sal^-}$=1.69); and detection limit for $TCO_2:\;4.0{\times}10^{-4}M$). In addition, the early potentiometric properties of the solid-state sensor with optimized membrane composition were not deteriorated for more than 60 days.

• Food Science and Preservation
• /
• v.7 no.4
• /
• pp.395-402
• /
• 2000

To enlarge application field of electrolyzed acid-water(EAW) on food industry, the changes of EAW properties by storage conditions and heating were investigatet. It was showed that storing EAW in closed container is mon effective to keep up the oxidation-reduction potentials(ORP), hyperchloride content and pH than stored in opened ones. ORP of EAW stored in closed container could be kept mon than 1 month as 1,150 mV levels. Ruing heating from 2$0^{\circ}C$ to 95$^{\circ}C$, ORP was increased to 1,150 mV levels at 95$^{\circ}C$ after gradual decrease to 5$0^{\circ}C$. Tyrosinase activity was decreased approximately to 26%~35% in EAW having a 950 mV~1,140 mV ORP. Also it was confirmed that EAW has anti-browning effect as sliced apple and potato, and their juices treated with EAW had conspicous difference in their $\Delta$E value. 12 kinds of pesticides such as aldrine, capful diazinon, diedrin, $\alpha$-endosulfan $\beta$-endosulfan, endosulfan sulfate, endrin, $\alpha$-BHC, o,p'-DDT, procymidone, PCNB added in EAW were recovered from ND~73.6% comparing to ones added in distilled water. The recovered amounts of pesticides, procymidone and diazinon in lettuce after soaking in EAW were 1.12 ppm and ND, compared with those of amounts soaked in distilled water were 3.67 ppm and 3.05 ppm respectively. So, it seems that EAW has potentials to promote the degradation of pesticides.