• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2001.11a
• /
• pp.59-62
• /
• 2001

Flow induced vibration in steam generators has caused dynamic interactions between tubes and contacting materials resulting in fretting wear . Series of experiments have been performed to examine the wear properties of Inconel 690 steam generator tubes in various environmental conditions. For the present study, the test rig was designed to examine the fretting wear and rolling wear properties in high temperature(room temperature - 290。C) water. The test was performed at constant applied load and sliding distance to investigate the effect of test temperature on wear properties of the steam generator tube materials. To investigate the wear mechanism of material, the worn was observed using scanning electron microscopy. The weight loss increase at higher test temperature was caused by the decrease of water viscosity and the mechanical property change of tube material. The mechanical property changes of steam generator tube material, such as decrease of hardness or yield stress in the high temperature tests. From the SEM observation of worn surfaces, the severe wear scars were observed in specimens tested at the higher temperature.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2001.11a
• /
• pp.220-228
• /
• 2001

Journal locus with aerated lubricant is analyzed under the dynamic loading condition. In this analysis, we have found that aerated lubricant influences two major factors on the film formation. One is the density variation of the lubricant due to the volume change by the bubbles and the other is the viscosity changes of the lubricant due to the surface tension of the bubble. Those two major factors surprisingly increase the load capacity in certain ranges of bubble sizes and densities. Modified Reynolds'equation is developed with the consideration of aerated ratio in the lubricant and journal locus is computed with Mobility method with the computation of two dimensional pressure distribution over the bearing area.

• Journal of Powder Materials
• /
• v.19 no.4
• /
• pp.304-309
• /
• 2012

The purpose of our study was to develop the fabrication method of porous diatomite ceramics with a porosity gradient by centrifugal molding. The processing variables of centrifugal molding were derived from Stoke's law of sedimentation, which were the radius of the particles, the acceleration due to centrifugal molding and the dynamic viscosity of the slurry. And these could be controlled by ball-milling conditions, centrifugal conditions, and the addition of methyl cellulose, respectively. The effects of processing conditions on the gradient pore structure of diatomite were investigated by particle size analysis, scanning electron microscope, and mercury porosimeter.

• Laser Solutions
• /
• v.9 no.1
• /
• pp.1-7
• /
• 2006

In order to increase the productivity of conventional microstereolithography (MSL), digital micromirror device($DMD^{TM}$) based MSL is proposed and the feasibility of 3D rnicrocomponents fabrication is demonstrated in two ways; free surface and constrained surface techniques. The clearness of optical images at the exposure plane was confirmed for the fabrication of an accurate 3D structure by controlling the dynamic viscosity of FA1260T and the shape accuracy of a structure fabricated with epoxy-based resin ($Somos^{\circledR}$ 10120) was analyzed to determine the optimum curing conditions. After finding the appropriate process variables, the feasibility of multiple microstructures is then demonstrated. Due to the high productivity, MSL using $DMD^{TM}$ showed the potential to replace the existing focused laser beam MSL.

• Wind and Structures
• /
• v.3 no.2
• /
• pp.73-81
• /
• 2000

Snowdrifts around buildings can cause serious problems when formed on undesirable places. The formation of snowdrifts is highly connected to the wind pattern around the building, and the wind pattern is again dependent on the building design. The shear stress on the surface and snowdrifting around different buildings are investigated through CFD analysis and compared to measurements. The computations of shear stress shows local minima in the same areas as snowdrifts are formed. The snowdrifting computations utilises a drift-flux model where a fluid with snow properties is allowed to drift through a fluid with air properties. An apparent dynamic viscosity of the snow/air mixture is defined and used as a threshold criterion for snowdrifting. The results from the snowdrifting computations show increased snow density where snowdrifts are expected, and are in agreement with previous large-scale snowdrift measurements. The results show that computational fluid dynamics can be a tool for planning building design in snowdrifting areas.

• Elastomers and Composites
• /
• v.51 no.2
• /
• pp.128-137
• /
• 2016

The effect of the surface area of silicas on their reinforcing performance to styrene-butadiene rubber (SBR) compounds was systematically investigated. The feasibility of the Brunauer-Emmett-Teller surface area ($S_{BET}$) as a parameter representing the characteristics of the silicas was discussed compared to the mesopore volume, c value, oil absorption, and uptake of silane. The increase in $S_{BET}$ of silicas caused a considerable increase in Mooney viscosity, minimum torque, and hysteresis loss of the silica-filled SBR compounds, while significantly enhancing their abrasion property. These changes were explained by the attrition between the hydrophilic silica surface and the hydrophobic rubber chains. As expected, the change in $S_{BET}$ did not induce any remarkable changes in the cure, processing, tensile, and dynamic properties of the silica-filled SBR compounds because the crosslinking density of the rubber chains mainly determined these properties.

• Elastomers and Composites
• /
• v.25 no.2
• /
• pp.97-102
• /
• 1990

Linear viscoelastic properties of 11 types of EPDM and 1 type of EPM rubbers have been measured at $210^{\circ}C$, using a RDS(Rheometrics dynamic spectrometer). The data base, i.e., complex viscosity, storage modulus, loss modulus, loss tangent and relaxation spectrum of the sample should be useful for rubber blending and compounding.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.31 no.2 s.257
• /
• pp.195-201
• /
• 2007

A visualization study of flow characteristics in a mixer using multi-nozzle bubbling was performed. The mixer is filed with liquid glycerin (dynamic viscosity = $1000mPa{\cdot}s\;at\;25^{\circ}C$) and convective mixing is induced by air bubbles generated from 9 orifices installed on the bottom of the mixer. To visualize the flow field, PIV (Particle Image Velocimetry) system consisting of 532nm Nd:YAG laser, $2k{\times}2k$ CCD camera and synchronizer is adopted. The bubbles generated with uniform size and frequency form bubble stream and bubble streams rise vertically without interaction between bubble streams. Mixing efficiency is affected by the height of bubbler and the effective height of bubbler is 20nm from the bottom of the mixer.

• Journal of Mechanical Science and Technology
• /
• v.20 no.10
• /
• pp.1716-1721
• /
• 2006

The Lubrication Mode of line contacts between the vane and the camring in an oil hydraulic vane pump has been investigated. First, the variations of the radial force of a vane were calculated from previous measurements of dynamic internal pressure in four chambers surrounding a vane. Next, the lubrication modes were distinguished with Hooke's chart, which is an improvement over Johnson's chart. Finally, the influence of the boundary conditions in the lubrication region on the fluid film lubrication was examined by calculating the film pressure distributions. The results showed that the lubrication mode of the vane tip exists in the rigid-variable-viscosity region, and that discharge pressure higher than 7 MPa greatly affects the oil film pressure in the small and the large arc section because of the Piezo-viscous effect.

• Korean Journal of Materials Research
• /
• v.16 no.10
• /
• pp.599-605
• /
• 2006

N-(3-triethoxysilylpropyl)-1,4-diaminoanthrquinone-2,3-dicarboximide (TESP-DADI), an organic blue pigment, has been prepared and incorporated into silica solid matrix reacting triethyl orthosilicate (TEOS) via sol-gel method. Morphology and microstructure of resulting hybrid pigment were studied employing SEM and TEM. The micrographs and particle size distributions showed that uniform pigment can be obtained employing TEOS-based sol-gel method forming silica core. Particle size distribution of dispersed pigment in water was examined using the technique of dynamic light scattering. The ensuing pigment dispersion ink was subjected to various physicochemical evaluation such as viscosity, surface tension, inkjet stability, storage stability, and color change as inkjet ink using spectrophotometric, and microscopic techniques.