• Geomechanics and Engineering
• /
• 제28권2호
• /
• pp.107-116
• /
• 2022

The steady state of unsaturated soil takes a long time to achieve. The soil seepage behaviours and hydraulic properties depend highly on the wetting/drying rate. It is observed that the soil-water characteristic curve (SWCC) is dependent on the wetting/drying rate, which is known as the dynamic effect. The dynamic effect apparently influences the scanning curves and will substantially affect the seepage behavior. However, the previous models commonly ignore the dynamic effect and cannot quantitatively describe the hysteresis scanning loops under dynamic conditions. In this study, a dynamic hysteresis model for SWCC is proposed considering the dynamic change of contact angle and the moving of the contact line. The drying contact angle under dynamic condition is smaller than that under static condition, while the wetting contact angle under dynamic condition is larger than that under static condition. The dynamic contact angle is expressed as a function of the saturation rate according to the Laplace equation. The model is given by a differential equation, in which the slope of the scanning curve is related to the slope of the boundary curve by means of contact angle. Empirical models can simulate the boundary curves. Given the two boundary curves, the scanning curve can be well predicted. In this model, only two parameters are introduced to describe the dynamic effect. They can be easily obtained from the experiment, which facilitates the calibration of the model. The proposed model is verified by the experimental data recorded in the literature and is proved to be more convenient and effective.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2000년도 추계학술발표대회 논문집
• /
• pp.38-41
• /
• 2000

High temperature cure characteristics of polyester resin systems were investigated by isothermal and dynamic differential scanning calorimetries. During isothermal scanning, the experimental procedure was modified to reduce the initial Boss of heat. no kinetic equation from the isothermal experiment was compared with that from the dynamic experiment.

• Elastomers and Composites
• /
• 제48권4호
• /
• pp.276-281
• /
• 2013

acrylic polyol로 개질한 polyester형 polyurethane foam을 quasi prepolymer법으로 제조하였다. 열적 및 동적 기계적 성질은 thermal gravimetric analysis 및 dynamic mechanical analysis에 의하여 분석하였다. 또한 유리전이온도는 differential scanning calorimeter로 측정하였다. Acrylic polyol 함량이 증가함에 따라 TGA에 의해 측정한 열적 안정성은 약간 감소하였다. 그리고 acrylic polyol 함량이 증가함에 따라 저장 탄성률은 증가한 반면에 tan delta 값은 감소하였다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2004년도 추계학술대회 논문집
• /
• pp.1380-1383
• /
• 2004

The scanning type XY stage is frequently used these days as precision positioning system in equipment for semiconductor or display element. It is requested higher velocity and more precise accuracy for higher productivity and measuring performance. The position accuracy of general stage is primarily affected by the geometric errors caused by parasitic motion of stage, misalignments such as perpendicular error, and thermal expansion of structure. In the case of scanning type stage, H type frame is usually used as base stage which is driven by two actuators such as linear motor. In the point view of scanning process, the stage is used in moving motion. Therefore, dynamic variation is added as significant position error source with other parasitic motion error. Because the scanning axis is driven by two actuators with two position detectors, 2 dimensional position errors have different characteristic compared to general tacked type XY stage. In this study 2D position error of scanning stage is analyzed by 1D heterodyne interferometer calibrator, which can measure 1D linear position error, straightness error, yaw error and pitch error, and perpendicular error. The 2D position error is evaluated by diagonal measurement (ISO230-6). The yaw error and perpendicular error are compensated on the base stage of scanning axis. And, the horizontal straightness error is compensated by cross axis compensation. And, dynamic motion error in scanning motion is analyzed.

• 한국소음진동공학회논문집
• /
• 제14권6호
• /
• pp.495-502
• /
• 2004

This paper presents the vibration analysis and the performance evaluation of cantilevers with probing tips for non-contact scanning probe microscopy. One of the current issues of the scanning probe microscopy technology is to increase the measurement speed, which is closely tied with the dynamic characteristics of cantilevers. The primary concern in this research is to investigate the relation between the maximum possible speed of non-contact scanning probe microscopy and the dynamic characteristics of cantilevers. First, the finite element analysis is made for the vibration characteristics of various cantilevers in use. The computed natural frequencies of the cantilevers are in good agreement with measured ones. Then, each cantilever is tested with topographic measurement for a standard sample with the scanning speed changed. The performances of cantilevers are analyzed along with the natural frequencies of cantilevers. Experiments are also performed to test the effects of how to attach cantilevers in the piezo-electric actuator. Finally, measurement sensitivity has been analyzed to enhance the performance of scanning probe microscopy.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2003년도 춘계학술대회논문집
• /
• pp.263-268
• /
• 2003

This paper presents a result of performance evaluation fur non-contact scanning probe microscopy with respect to the vibration characteristics of cantilevers with tips. One of the current issues of the scanning probe microscopy technology is to increase the measurement speed, which is closely tied with the dynamic characteristics of cantilevers. The primary concern in this research is to investigate the relation between the maximum possible speed of non-contact scanning probe microscopy and the dynamic characteristics of cantilevers. First, the finite element analysis is made fur the vibration characteristics of various cantilevers in use. The computed natural frequencies of the cantilevers are in good agreement with measured ones. Then, each cantilever is tested with topographic measurement for a standard sample with the scanning speed changed. The performances of cantilevers are analyzed along with the natural frequencies of cantilevers. Experiments are also performed to test the effects of how to attach cantilevers in the piezo-electric actuator. Finally, measurement sensitivity has been analyzed to enhance the performance of scanning probe microscopy.

• 한국병원경영학회지
• /
• 제12권2호
• /
• pp.93-111
• /
• 2007

The thrust in this paper is to discuss the dimensions of executive scanning process (ESP) that support continuous scanning activities by executives. Executive scanning is especially important for the healthcare organizations in these days since the environment they are faced with is extremely complex and dynamic. While much has been written about ESP, two important aspects have been underemphasized in the past. The first is a link to the strategic management process (SMP) or the issue of strategy-scanning alignment. The second is a feedback loop to verify the quality of information generated through scanning process. This paper discusses the improved ESP by adding these two features.

• Elastomers and Composites
• /
• 제38권4호
• /
• pp.326-333
• /
• 2003

Dynamic DSC 방법을 이용하여 isoprene(IR) 및 chloroprene(CR) 고무로 개질된 NR/CB 고무 복합체의 가황반응을 연구하였다. 각각의 샘플에 대하여 승온속도를 달리한 열분석 곡선을 얻었고 이로부터 Kissinger의 해석 방법에 따라 가교반응 기구를 연구하였다. 실험에 사용된 고무 복합재료는 대개 $120{\sim}180^{\circ}C$ 사이의 온도영역에서 가교 반응이 일어나는 것이 확인되었으며, 승온속도가 $3^{\circ}C/min$에서 $30^{\circ}C/min$로 빨라질수록 최대반응 속도점의 온도($T_p$)는 점점 높은 쪽으로 이동하였고, 반응 발열량도 상대적으로 커지는 것으로 관찰되었다. Kissinger의 해석방법을 이용하여 실험 데이터를 분석한 결과, 실험에 사용된 샘플의 가교반응은 1차반응에 의해 진행되는 것으로 밝혀졌으며 개질제로서 사용된 고무 중에서 IR을 사용한 경우보다는 CR을 개질제로 사용한 경우에 반응온도에 상대적으로 더 민감한 것으로 판명되었다. 그러나 충전제로 사용된 카본블랙의 경우에는 종류와는 무관하게 반응기구에는 거의 영향을 미치지 않는 것으로 밝혀졌다.

• 대한원격탐사학회지
• /
• 제16권2호
• /
• pp.135-143
• /
• 2000

Ocean Scanning Multispectral Imager (OSMI) is a payload on the Korean Multi-Purpose SATellite (KOMPSAT) to perform global ocean color monitoring for the study of biological oceanography. HOMPSAT was launched 21 December 1999. The radiometric performance of OSMI is analyzed for various gain settings in the viewpoint of the instrument developer for OSMI calibration and application based on its ground performance data measured before launch. The radiometric response linearity and dynamic range are analyzed and the dynamic range is compared with the nominal input radiance for the ocean and the land. The noise equivalent radiance (NER) corresponding to the instrument radiometric noise is compared with the radiometric resolution of signal digitization (1-count equivalent radiance). The best gain setting of OSMI for ocean monitoring is recommended. This analysis is considered to be useful for the OSMI mission and operation planning, the OSMI image data calibration, and users' understanding about OSMI image quality.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1998년도 추계학술대회 논문집
• /
• pp.133-136
• /
• 1998

The scanning Maxwell-stress microscopy (SMM) is a dynamic noncontact electric force microscopy that allows simultaneous access to the electrical properties of molecular system such as surface potential, surface charge, dielectric constant and conductivity along with the topography. Here we report our recent results of its application to nanoscopic study of domain structures and electrical functionality in organic thin films prepared by the Langmuir-Blodgett technique.