• Applied Chemistry for Engineering
• /
• v.8 no.6
• /
• pp.960-966
• /
• 1997

The effects of epoxy resins and content of catalyst on the cure characteristics were studied by FT-IR, DSC and dynamic viscometer for the thermal properties and rheological properties of the catalytic (N-Benzylpyrazinium hexafluoroantimonate, BPH) epoxy thermosetting system. Compared with DSC results of DEGBF containing 0.5wt% BPH, the DSC thermograms of DGEBA containing 0.5wt% BPH indicated that the reaction was faster than that of DGEBF/BPH and the conversion rate of DGEBA/BPH was high in the initial stage of the reaction. As the concentration of BPH increases, the reaction and conversion rates show similar value in both the cases. The influence of hydroxyl group of epoxy resin on gel point defined from the crossover point of storage modulus (G') and loss modulus (G") could be explained by the formation of 3-dimensional network in the initial stage owing to the curing reaction between epoxides and hydroxyl groups of epoxy resin. This was consistent with the gel point obtained from DSC, FT-IR and moduli crossover. The activation energy (Et) obtained from the crossover point (G'/G"=1) are $31-39kJ.mol^{-1}$ for various BPH compositions in case of two epoxy systems.

• Polymer(Korea)
• /
• v.37 no.2
• /
• pp.240-248
• /
• 2013

The curing behaviors of diglycidyl ether of bisphenol A (DGEBA) with mercaptan hardener were studied by the comparison with amine-adduct type hardener. Curing behaviors were evaluated by DSC at dynamic and isothermal conditions. In the DSC, the dynamic experiments were based on the method of Kissinger's equation, and the isothermal experiments were fitted to the Kamal's kinetic model. Activation energy of epoxy/amine-adduct type hardener was ca. 40 kcal/mol. As the functional group of mercaptan hardener, -SH increased, on epoxy/mercaptan hardeners, the activation energies decreased from 28 to 19 kcal/mol. Epoxy/amine-adduct type hardener was initiated at $90^{\circ}C$ or higher. However, epoxy/mercaptan hardeners reduced the initiation temperatures below $80^{\circ}C$ and shortened the durations of curing reaction within 10 min. We found out that the reaction kinetics of epoxy with mercaptan hardener followed the autocatalytic reaction models, and the maximum reaction rates were shown at the conversions of 20~40%.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.12 no.1
• /
• pp.122-129
• /
• 2008

The direct torque control method of an inverter fed squirrel cage typed induction motor using fuzzy logic controller has been proposed. This method is suitable for the traction which requires a fast torque response during the star-up and step change. The fuzzy control algorithm based upon the control principles of conventional DSC(Direct Self Controller) is developed. The fuzzy algorithm is tarried out by defuzzification strategy of the fuzzy output extracted from the possibility distribution of an inferred fuzzy control rule. The flux and torque of an induction motor are estimated by the dynamic model of the rotor flux field-oriented scheme which has decoupling characteristics and excellent dynamic response over a wide speed range. The proposed controller shows a good dynamic response. Moreover, since the fuzzy controller possesses highly adaptive capability, the performance of fuzzy controller is quite robust and insensitive to the motor parameters and change of operation conditions.

• Applied Chemistry for Engineering
• /
• v.3 no.1
• /
• pp.111-118
• /
• 1992

The curing acceleration of epoxy/amine system was investigated by using differential scanning calorimeter(DSC), The epoxy, diglycidylether of bisphenol A (DGEBA) was cured with methylene dianiline (MDA) with or without accelerators. Two kinds of accelerators were tested for the study ; tris(dimethylaminomethyl)phenol (DMP - 30) and 3 - (3,4 - dichlorophenyl)-1, 1-dimethylurea (DIURON). Heats of reaction and glass transition temperatures ($T_g$) of the cured epoxy system were analyzed by DSC along with the estimation of activation energy by the dynamic DSC studies. It was found that DMP - 30 is more effective accelerator than DIURON which showed faster curing and lower activation energy.

• Korean Journal of Radiology
• /
• v.22 no.8
• /
• pp.1369-1378
• /
• 2021

Objective: Few attempts have been made to investigate the prognostic value of dynamic contrast-enhanced (DCE) MRI or dynamic susceptibility contrast (DSC) MRI of non-enhancing, T2-high-signal-intensity (T2-HSI) lesions of glioblastoma multiforme (GBM) in newly diagnosed patients. This study aimed to investigate the prognostic values of DCE MRI and DSC MRI parameters from non-enhancing, T2-HSI lesions of GBM. Materials and Methods: A total of 76 patients with GBM who underwent preoperative DCE MRI and DSC MRI and standard treatment were retrospectively included. Six months after surgery, the patients were categorized into early progression (n = 15) and non-early progression (n = 61) groups. We extracted and analyzed the permeability and perfusion parameters of both modalities for the non-enhancing, T2-HSI lesions of the tumors. The optimal percentiles of the respective parameters obtained from cumulative histograms were determined using receiver operating characteristic (ROC) curve and univariable Cox regression analyses. The results were compared using multivariable Cox proportional hazards regression analysis of progression-free survival. Results: The 95th percentile value (PV) of Ktrans, mean Ktrans, and median Ve were significant predictors of early progression as identified by the ROC curve analysis (area under the ROC curve [AUC] = 0.704, p = 0.005; AUC = 0.684, p = 0.021; and AUC = 0.670, p = 0.0325, respectively). Univariable Cox regression analysis of the above three parametric values showed that the 95th PV of Ktrans and the mean Ktrans were significant predictors of early progression (hazard ratio [HR] = 1.06, p = 0.009; HR = 1.25, p = 0.017, respectively). Multivariable Cox regression analysis, which also incorporated clinical parameters, revealed that the 95th PV of Ktrans was the sole significant independent predictor of early progression (HR = 1.062, p < 0.009). Conclusion: The 95th PV of Ktrans from the non-enhancing, T2-HSI lesions of GBM is a potential prognostic marker for disease progression.

• Elastomers and Composites
• /
• v.19 no.1
• /
• pp.13-31
• /
• 1984

The purposes of this dissertation are to demonstrate that DSC theromoanaytical methods of vulcanization can provide useful informations on the vulcanization characteristics of industrial formulations and also provides the potential basis for a rapid and complete method of sulfur and vulcanizing accelerator analysis for quality control. The influences of those factors such as heating rate, scan temperature, vucanizing accelerator's type and concentration upon vulcanization exotherm in NR and NBR compounds in the presence of vulcanizing accelerators such as TMTD,MBTS,DPG,TMTM,CBS, and MBT were evaluated by means of DSC. In order to examine the credibility in the DSC method, the same samples which were used for DSC method were studied to compare the DSC results with the ODR (Oscillating Disk Rheometer) data. The results obtained were as follows 1. In the DSC dynamic experiments, the observed enthalpy results from vulcanization depends upon the heating rate; In the range of 2 to $20^{\circ}C/min$ of heating rate, as the heating rate was increased the enthalpy change was also increased. However, over the heating rate of $30^{\circ}C/min$ it was observed that the enthalpy change was decreased as the heating rate was further increased. Without regard to the change of enthalpy, tremendous instantaneous heat evolving was observed in the range of high heating rates. 2. For the samples which are added with various vulcanizing accelerators, the activation energies of vulcanization were as follows; 3. Regarding to the influences of vulcanizining accelerator's types upon the characteristics of vulcanization exotherm, NR and NBR compounds in the presence of thiuramsulphide compounds type accelerators such as TMTD, TMTM, were exhibited sharper and higher vulclanization exotherm than others. From the resuts of DSC thermograms which was distributed in even shape in the broad temperature range, it was clearly shown that the guanidine compounds type accelerator such as DPG acts as a delayed acting accelerator. 4. In the comparison of DSC and ODR results, the dependency of temperature in the cure rate and the observed conversions show good agreements between two results. 5. In the same curatives, by the comparison of glass transition temperatures, it was possible to predict relative values of maximum torques. Consequently, from the present studies, it is shown that the DSC thermoanalytical method can provide an alternate new method for rapid and complete quality control analysis of rubber industry.

• Applied Chemistry for Engineering
• /
• v.7 no.2
• /
• pp.387-392
• /
• 1996

Natural zeolite/epoxy resin composites were prepared and the cure kinetics was studied by dynamic DSC analysis. With the increments of natural zeolite content, the reaction starting temperature and the exothermic peak temperature were decreased. When diglycidyl ether of bisphenol A(DGEBA)/4,4'-methylene dianiline(MDA)/malononitrile(MN, 10phr) was filled with 20phr of zeolite, DSC thermogram had one peak and when it was filled with 30phr of zeolite, a shoulder appeared on the DSC thermogram. With the filling of 40phr of zeolite, DSC thermogram was separated into two peaks and the activation energy of the first peak, $Ea_1$ was 12.30 kJ/mol and that of the second peak, $Ea_2$ was 12.70 kJ/mol.

• Korean Journal of Radiology
• /
• v.22 no.9
• /
• pp.1537-1546
• /
• 2021

Objective: To assess the role of arterial spin-labeling (ASL) perfusion MRI in identifying cerebral perfusion changes after indirect revascularization in children with moyamoya disease. Materials and Methods: We included pre- and postoperative perfusion MRI data of 30 children with moyamoya disease (13 boys and 17 girls; mean age ± standard deviation, 6.3± 3.0 years) who underwent indirect revascularization between June 2016 and August 2017. Relative cerebral blood flow (rCBF) and qualitative perfusion scores for arterial transit time (ATT) effects were evaluated in the middle cerebral artery (MCA) territory on ASL perfusion MRI. The rCBF and relative time-to-peak (rTTP) values were also measured using dynamic susceptibility contrast (DSC) perfusion MRI. Each perfusion change on ASL and DSC perfusion MRI was analyzed using the paired t test. We analyzed the correlation between perfusion changes on ASL and DSC images using Spearman's correlation coefficient. Results: The ASL rCBF values improved at both the ganglionic and supraganglionic levels of the MCA territory after surgery (p = 0.040 and p = 0.003, respectively). The ATT perfusion scores also improved at both levels (p < 0.001 and p < 0.001, respectively). The rCBF and rTTP values on DSC MRI showed significant improvement at both levels of the MCA territory of the operated side (all p < 0.05). There was no significant correlation between the improvements in rCBF values on the two perfusion images (r = 0.195, p = 0.303); however, there was a correlation between the change in perfusion scores on ASL and rTTP on DSC MRI (r = 0.701, p < 0.001). Conclusion: Recognizing the effects of ATT on ASL perfusion MRI may help monitor cerebral perfusion changes and complement quantitative rCBF assessment using ASL perfusion MRI in patients with moyamoya disease after indirect revascularization.

• Elastomers and Composites
• /
• v.48 no.4
• /
• pp.276-281
• /
• 2013

Polyester type polyurethane foam modified with acrylic polyol was prepared by quasi prepolymer method. Thermal and dynamic mechanical properties of polyurethane foam were analysed by thermal gravimetric analysis(TGA) and dynamic mechanical analysis(DMA). Also, glass transition temperature was measured by differential scanning calorimeter(DSC). As acrylic polyol contents were increased, thermal stability measured by TGA was slightly decreased. Storage modulus was increased and tan delta was decreased with increasing of acrylic polyol contents.

• Korean Journal of Materials Research
• /
• v.2 no.4
• /
• pp.257-262
• /
• 1992

The cure kinetics of a diglycidyl ether of bisphenol A (DGEBA) with 4, 4'-methylene dianiline (MDA) added succinonitrile was studied through the dynamic run method by applying the data to the Kissinger equation which analyses the effect of the heating rate on the temperature at maximum reaction rate using Differential Scanning Calorimetry (DSC) analyzer in the range of 3$0^{\circ}C$-35$0^{\circ}C$. In the DGEBA/MDA system with SN, the activation energy ($E_a$) and the pre-exponential factor (A) were calculated. From these results, the rate constants (k) were obtained according to the different SN contents.