• Proceedings of the KIEE Conference
• /
• 2006.07b
• /
• pp.635-636
• /
• 2006

A pulse with modulation(PWM) that keeps a constant angle of dwell and adjust duty ratio is a good method to control a speed of SRM. And a method of one pulse control is proper a operation on range of high speed in SRM for a good energy efficiency. Because PWM method is more safety than one pulse method, conversion of those is best choice according the speed range. So, some algorithm is need for smooth conversion of the mode of control. This paper presents a factor of conversion that proper the conversion of control mode between PWM and one pulse method This factor is from estimation of torque and proper at the variable range of conversion and show the better conversion characteristic than constant factor of conversion.

• Proceedings of the KIEE Conference
• /
• 2006.07b
• /
• pp.1055-1056
• /
• 2006

This paper presents a remote dimming control method for the electrodeless lamps using 2.4 GHz RF communication. Since the proposed dimming method are implemented with a simplest open loop control using ISM band HF modem and low cost MCUs, and the remote controller has just several functions such as On/Off and duty ratio increasing/decreasing. It can be made with low cost. In this paper, the detailed digital logics of the proposed remote dimming control are described and the experimental results are presented.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.05b
• /
• pp.60-64
• /
• 2005

Discharge of the flat lamp lighting source research are requested very much. For improving brightness, life time, efficiency of flat lamp, plasma diagnosis of the flat lamp lighting source to understand property of lighting source is very important, distance of discharge electrode is 5.5mm and width is 16.5mm, we measured electron temperature and electron density measured with single langmuir probe in flat lamp, we tested the discharge from 100 Torr to 300 Torr pressure, the Pulse is rectangular pulse with frequency 20kHz and Duty ratio 20%. Resultly, electron temperature decreases and electron density increase as increase the gas pressure and electron temperature decreases and electron density increase as increase the voltage.

• Proceedings of the KIEE Conference
• /
• 2006.07b
• /
• pp.781-782
• /
• 2006

This paper presents a drive strategy to reduce torque ripple of a permanent magnet Brushless DC Motor(BLDCM) with short $120^{\circ}$ flat top Back Electromotive Force(Back-EMF). In this strategy, the phase Back-EMF is divided into four sections. Then, in each section the phase current is regulated by corresponding PWM duty ratio to compensatethe torque ripple caused by imperfect Back-EMF. A program based on this strategy has been implemented in MATLAB@Simulink. The validity of the presented method is verified by simulation results.

• Journal of the Korean Institute of Telematics and Electronics B
• /
• v.28B no.5
• /
• pp.411-420
• /
• 1991

In this paper, SPICE program which is widely used in analysis of general circuit on electronic and electrical field has been applied to DC-DC converter. We have selected Forward type which is widely used us SMPS(Switched Mode Power Supply) of various electronic equipments, and have confirmed the waveforms of circuit operation, transfer of energy and resetting in transformer. And the procedure which the output voltage of converter, including the control circuit, has been stabilized from the transient state to the steady state by controlling the duty ratio of switch is presented. We have compared SPICE simulation with experiment and have verified the validity of SPICE simulation.

• 한국태양에너지학회:학술대회논문집
• /
• 2011.04a
• /
• pp.299-303
• /
• 2011

This paper proposes a novel sensorless maximum power point tracking (11PPT) algorithm for PV systems. The method is based on dividing the operating time into several intervals in which the PV terminals are short circuited in one interval and the calculated short-current of the PV is obtained and used to determine the optimum operating point where the maximum output power can be obtained. The proposed MPPT algorithm has been introduced into a current-controlled boost converter whose duty ratio is controlled to the maintain MPP condition. The same sequence is then repeated regularly capturing the PV maximum power. The main advantage of this method is eliminating the current sensor. Meanwhile, this MPPT algorithm reduces the power oscillations around the peak power point which occurs with perturbation and observation algorithms. In addition, the total cost will decrease by removing the current sensor from the PV side. Finally, simulation results confirm the accuracy of the proposed method.

• Journal of the Optical Society of Korea
• /
• v.16 no.2
• /
• pp.107-114
• /
• 2012

In this paper, we propose a new modulation scheme called multi-coded variable pulse position modulation (MC-VPPM) for visible light communication systems. Two groups of signals (Pulse Width Modulation (PWM) and Pulse Position Modulation (PPM) groups) are multi-coded by orthogonal codes for transmitting data simultaneously. Then, each multi-level value of the multi-coded signal is converted to pulse width and position which results in not only an improved data rate, but also a processing gain in reception. In addition, we introduce average duty ratio and cyclic shift concepts in PWM through which dimming control for light illumination can be supported without any degradation in communication performance. Through simulation, we confirm that the proposed MC-VPPM shows a comparable BER curve and much greater achievable data rate than the conventional VPPM scheme using a visible light optical channel environment.

• Nuclear Engineering and Technology
• /
• v.35 no.3
• /
• pp.214-225
• /
• 2003

A teleoperated manipulator system has been developed for remote handling of the spent fuel bundles. A heavy-duty power manipulator with high reduction ratio joints is used for the slave manipulator in the developed system since the handling tasks of the spent fuel bundles need power. Also, the universal type master manipulator, which has force reflecting capability, is used for precise remote manipulation. The power manipulators so frequently occur the control input saturation that the precise control performances are not achieved due to the windup phenomenon. An advanced bilateral control scheme compensating for the saturation is applied to the teleoperated manipulator system. The validity of the developed system is verified by the grid cutting and fuel transportation tasks from the mockup spent fuel bundle.

• Proceedings of the KIEE Conference
• /
• 1997.07a
• /
• pp.221-223
• /
• 1997

This paper deals with the slip power recovery system using switch mode converter in the inverter DC side, which recovers slip power of induction machine to AC line with the aid of the boost converter. As a results, the motor speed can be controlled by the duty ratio of boost switch, not by inverter firing angle. This results that the reactive power produced by phase controlled inverter and diode rectifier can be greatly reduced and linear speed regulation can be obtained. Moreover, the harmonic components of line current caused by the commutation in inverter and rectifier can be considerably suppressed. Therefore, most of the problems in conventional system can be solved.

• Journal of Biomedical Engineering Research
• /
• v.17 no.3
• /
• pp.373-378
• /
• 1996

In this paper, we calculated chronaxy value in order to determine the optimal conditions and stimulus pulse of information transmission. We also developed an electrical equivalent circuit of the hand including the contact part, which consists of two resistors (a contact resistor and finger resistor) and a capacitor. The minimum recoulition voltage was measured by using electrical stimulus. We found that the ranges of the above two resistances and the capacitance are 30-130k$\Omega$, 20-60k$\Omega$ and 10-30nF respectively. We found that the minimum recoulition voltage was the lowest at 100-300Hz and 10% of the duty ratio.