• KSII Transactions on Internet and Information Systems (TIIS)
• /
• 제11권5호
• /
• pp.2433-2452
• /
• 2017

Recently, the pipeline-forwarding has been proposed as a new technique to resolve the end-to-end latency problem of the duty-cycle MAC protocols in Wireless Sensor Networks (WSNs). Some protocols based on this technique such as PMAC and PRI-MAC have shown an improvement not only in terms of reducing end-to-end latency but also in terms of reducing power consumption. In these protocols, however, the sensor nodes still waste a significant amount of energy for unnecessary idle listening during contention period of upstream nodes to check the channel activity. This paper proposes a new pipeline-forwarding duty-cycle MAC protocol, named RP-MAC (Reduced Pipelined duty-cycle MAC), which tries to reduce the waste of energy. By taking advantage of ACK mechanism and shortening the handshaking procedure, RP-MAC minimizes the time for checking the channel and therefore reduces the energy consumption due to unnecessary idle listening. When comparing RP-MAC with the existing solution PRI-MAC and RMAC, our QualNet-based simulation results show a significant improvement in term of energy consumption.

• 전기전자학회논문지
• /
• 제24권1호
• /
• pp.326-332
• /
• 2020

본 논문은 듀티사이클 기반의 무선센서네트워크에서 에너지 효율성을 높이고 시간 지연을 줄일 수 있는 경로설정을 위해 새로운 라우팅 메트릭을 고안하고 이를 활용한 라우팅 프로토콜을 제안한다. 듀티사이클을 고려한 새로운 라우팅 메트릭인 EDW 메트릭을 사용함으로써 에너지 효율적이며 저지연의 경로를 설정할 수 있다. 본 논문에서는 새로운 라우팅 메트릭을 적용하는 크로스레이어 기반의 다중경로 라우팅 프로토콜을 제안하고 실험을 통해 낮은 전송 지연시간과 적은 에너지소비를 확인하였다.

• 한국분무공학회지
• /
• 제21권3호
• /
• pp.130-136
• /
• 2016

NOx and PM are important air pollutants as vehicle management policy aspect. Medium-duty truck is the main source of the pollutants although the vehicle market share is only 3.5%. National emission portion of NOx and PM form the mobile sourece are 14% and 16% respectively. In this study it was investigated that characteristics of air pollutants emission on medium duty truck equipped with EGR and SCR system. Vehicle's test reflected driving cycle on the chassis dynamometer, and applied test cycle was WHVC(World Harmonized Vehicle Cycle) mode. The test cycle include three segments, represent urban, rural and motorway driving. Based on the test results NOx, PM, HC were less emitted form SCR vehicle than EGR vehicle. And CO was less emitted form EGR vehicle than SCR vehicle due to CO oxidation reaction on DPF surface. And most air pollutants reduced as average vehicle speed increased. Pollutants were less emitted on motorway section than urban and rural sections. But highly NOx emission on motorway section was verified according to increased EGR ratio on fast vehicle speed. HC and CO additional emission was identified as 68%, 58% respectively during SCR vehicle's cold engine start emission test. NOx additional emission was detected by 24% on SCR vehicle's condition of engine cold start while not detected on vehicle equipped with EGR. SCR vehicle's additional NOx emission was derived from low reaction temperature during engine cold start condition. medium-duty truck emission characteristics were investigated in this study and expected to used to improve air pollutants management policy of medium-duty truck equipped with SCR & EGR.

• 한국정보통신학회논문지
• /
• 제22권4호
• /
• pp.670-675
• /
• 2018

센서네트워크의 전력문제를 해결할 수 있는 에너지 수집형 무선 센서네트워크 (EH-WSN)에 대한 관심이 증가하고 있다. EH-WSN에서는 에너지 수집과 소비의 균형을 맞추기 위한 on-off 듀티싸이클링에 관한 연구가 많이 진행되고 있다. 그러나 환경감시를 위한 EH-WSN에서 센싱된 데이터의 긴급성과 에너지 수집율은 네트워크의 성능을 결정하는 중요한 요소가 된다. 따라서 단순히 전력의 균형 상태를 유지하는 것 이외에 센싱된 데이터의 중요도 및 에너지 수집율에 따라 듀티싸이클 주기를 조절할 필요성이 대두된다. 본 논문에서는 환경감시를 위한 EH-WSN에서 기존의 전력만을 고려한 on-off 듀티싸이클링의 문제점을 분석하고, 센싱값의 변화율 및 크기값에 의한 센싱 데이터의 우선순위 및 에너지 수집율 등을 고려하여 적응적으로 on-off 주기를 결정하는 듀티싸이클 스케줄링 기법을 제안한다. 시뮬레이션을 통해 제안된 듀티싸이클 스케줄링의 성능을 분석하였다.

• 한국인터넷방송통신학회논문지
• /
• 제16권1호
• /
• pp.193-198
• /
• 2016

안전한 플랜트 설비의 상태 감시 및 장애 진단을 위해 무선 센서를 이용한 플랜트 설비용 모니터링 시스템이 연구되고 있다. 플랜트 설비에서는 저전력 뿐만 아니라 안전사고와 직결된 긴급 상황시 실시간성도 고려해야 한다. 본 논문에서는 플랜트 시설에서 지연시간 감소를 위한 동적 듀티사이클 조절 기법을 제안한다. 제안된 동적 듀티사이클 조절 기법은 센싱된 데이터 값의 긴급한 정도에 따라 미리 정의된 위험 그룹으로 구분하여 적응적으로 듀티사이클 주기를 조절한다. 실시간성을 평가하기 위해 고정 듀티사이클 기법과 동적 듀티사이클의 예상 지연시간을 확률적으로 분석하였다. 비교 결과, 플랜트 시설과 같이 이상 징후 발생 시 에너지를 소모하더라도 실시간성을 제공해야 하는 상황에서 제안 동적 듀티사이클 기법이 더 효과적임을 확인하였다.

• Corrosion Science and Technology
• /
• 제5권5호
• /
• pp.168-172
• /
• 2006

Alloy 600 having a superior resistance to a corrosion is used as a steam generator tubing in nuclear power plants. In spite of its high corrosion resistance, there are many tubings which experience corrosion problems such as a SCC under the high temperature and high pressure environments of nuclear power plants. The Alloy 600 tubing can be repaired by using a Ni electroplating having an excellent SCC resistance. In order to carry out a successful Ni electrodeposition inside a steam generator tubing, the effects of various parameters on the material properties of the electrodeposit should be elucidated. Hence this work deals with the effects of an applied current density, duty cycle($T_{on}/(T_{on}+T_{off})$) of a pulse current, bath temperature and solution pH on the material properties of Ni electrodeposit obtained from a Ni sulphamate bath by analyzing the current efficiency, potentiodynamic curve, hardness and stress-strain curve. Hardness, YS(yield strength) and TS(tensile strength) decreased whereas the elongation increased as the applied current density increased. This was thought to be by a concentration depletion at the interface of the electrodeposit/solution, and a fractional decrease of the hydrogen reduction reaction. As the duty cycle increased, the hardness, YS and TS decreased while the elongation increased. During an off time at a high duty cycle, the concentration depletion could not be recovered sufficiently enough to induce a coarse grain sized electrodeposit. With an increase of the solution temperature and pH, the YS and TS increased while the elongation decreased. The experimental results of the hardness and the stress-strain curves can be supplemented by the results of the potentiodynamic curve.

• 산업경영시스템학회지
• /
• 제28권3호
• /
• pp.75-86
• /
• 2005

To investigate the fatigue characteristic of upper limbs, this study analyzed RMS(root mean square) and MPF(mean power frequency) value between initial and terminal stages of each experiment condition. And the effect of intermittent endurance time was evaluated using the Borg's CR10 value that was measured for the parts of upper limb. According to the results of ANOVA on RMS value, there were significant difference on the %MVC about push, pull, and down force exertion. Particularly the ANOVA of up force exertion was significant difference on shoulder flexion, elbow flexion and rest time as well as %MVC. The results of ANOVA for MPF value were significant difference on the %MVC in regard of the push and up force exertion. In case of up force exertion, MPF value tended to shift low frequency at all of the experiment conditions. According to the analysis of duty cycle, RMS value considerably increased over 50% duty cycle and as the %MVC increased, the duty cycle affected the increase of RMS value. MPF value for up and down force exertion decreased at 33%, 50% and 67% duty cycle for all of %MVC. Borg CR10 value of hand and forearm were below the 3-point to the 40% of endurance time at 30%MVC and to the 20% of endurance time at 50%MVC with the exception of up force exertion. But Borg CR10 values of upper arm and shoulder at up force exertion were more than 3-point to the 20% of endurance time at 30%MVC and in the start point of endurance time at 50%MVC.

• 한국유체기계학회 논문집
• /
• 제18권6호
• /
• pp.81-85
• /
• 2015

The purpose of this study is to evaluate energy savings for inverter driving multi-stage centrifugal pump. Variable speed driving pump system has high efficiency compared with constant speed driving pump system. Because of difficulty to estimate operating efficiency of variable speed driving pump system, energy saving rates are used to replace operating efficiency. energy saving rates are calculated from pump input power and pump duty cycle. But another researches have used pump duty cycles of each season for energy saving rate. In this study, for estimating energy saving rate more high accuracy, pump duty cycles are measured for 1 year. pump duty cycles, depending on the season and be classified according to the weekday/weekend or during the week day. By this pump duty cycles, Energy saving rate is calculated appropriately.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1996년도 하계학술대회 논문집 A
• /
• pp.486-488
• /
• 1996

A dc-dc converter which transfers l2-48W of power(regulated output voltage 24V) across a large, variable air gap(1-2cm) has been designed. This converter employs double resonance to compensate the large leakage inductance of the primary and secondary of the transcutaneous transformer. To maximize the effect of resonance, a constant frequency, duty cycle control method is used. The duty cycle control presents advantages over a frequency control in terms of increase in dc voltage gain and reduction of the primary current. The analysis and design procedure for the proposed scheme is presented and the performance result is simulated and verified experimentally.

• International Journal of Precision Engineering and Manufacturing
• /
• 제9권3호
• /
• pp.82-84
• /
• 2008

A surface encoder based on the Half-shaded square pattern (HSSP) is presented. The HSSP working as reference grid is composed of the straight lines which are easy to be fabricated and make measuring time short. Since the periodic cell is separated in ON/OFF by the $45^{\circ}$ straight line, the duration from the starting point of scanning to the first rising edge and the duty cycle of the pulse train vary with respect to the position of the starting point. And the relationship between X and Y position and the duration, and duty cycle is described in the simple linear equation. Therefore, it is possible to measure X and Y position with the measured duration and duty cycle without calculating load. Through the test set-up, the feasibility of the proposed surface encoder was verified. Also the future works for improvement of performance were suggested.