• Proceedings of the KIEE Conference
• /
• 1999.07f
• /
• pp.2736-2738
• /
• 1999

Power electronic loads inject harmonic currents into the utility system. The large increase of power consumption will inevitably lead to deteriorating power quality due to the popularization of switch-mode power electronic equipment. In this paper, a periodic voltage is injected in the control circuit to vary duty cycle of the rectifier switch within a line cycle so that the fifth-order harmonic of the input current is reduced to meet the IEC 61000-3-2 requirement. Experimental results are presented to confirm the validity of this method.

• Journal of Korea Multimedia Society
• /
• v.20 no.2
• /
• pp.254-260
• /
• 2017

Data packets from sensor nodes scattered over measuring fields are generally forwarding to the sink node, which may be connected to the wired networks, in a wireless sensor network. So many data packets are gathered near the sink node, resulting in significant data packet collisions and severe transmission latency. In an event detection application such as object tracking and military, bursty data is generated when an event occurs. So many data packet should be transmitted in a limited time to the sink node. In this paper, we present a delay efficient and bursty traffic friendly MAC protocol called DEBF-MAC protocol for wireless sensor networks. The DEBF-MAC uses a slot-reserved mechanism and sleep period control method to send multiple data packets efficiently in an operational cycle time. Our simulation results show that DEBF-MAC outperforms DW-MAC and SR-MAC in terms of energy consumption and transmission delay.

• Proceedings of the KAIS Fall Conference
• /
• 2003.06a
• /
• pp.267-270
• /
• 2003

All artificial infernal organs which are using electric energy supply energy with inductive couple. Transcutaneous energy transmission system enhance survival chance of the patients and quality of life by reducing volume and mass. In this research, we used both tune in transmission system in state of fixing cycle in order to increase the voltage gain and the current gain and to reduce effect of leakage inductance. Also to maximize the effect of resonance, a constant frequency duty cycle control method is used. Test is progressed with litz wire which is set up with various sizes of core to minimize size of converter. This research aimed in analysis of transcutaneous energy transmission system and in measuring of stability and efficiency of Lithium-ion battery charge which are using transmitted energy.

• 제어로봇시스템학회:학술대회논문집
• /
• 2004.08a
• /
• pp.509-514
• /
• 2004

This paper introduces the modified slip energy recovery system in order to improve its power factor and to reduce harmonics of line current waveforms. Twelve pulse line commutated converter with the chopper type IGBT is applied where the chopper is applied across the DC terminal and the chopped DC is fed to the converter operating as an inverter and then passed through the wye-wye and delta-wye transformer circuit. This scheme leads to be able to adjust the speed of the motor by the duty cycle of the chopper operating in PWM mode. The fuzzy logic controller is also introduced to the modified slip energy recovery system for keeping the motor speed to be constant when the load varies. The experimental results in testing the 0.22 kW wound rotor induction motor from no-load condition to rated condition show the effectiveness of the proposed control scheme.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.16 no.11 s.116
• /
• pp.1165-1171
• /
• 2006

This paper presents a new type of jetting dispenser for the integrated circuit (IC) fabrication and surface mount technology The proposed system is featured by the piezoelectric actuator and hydraulic magnification device. After describing structural component of the dispensing mechanism and its operation principle, both the fluid modeling and the hydraulic magnification modeling are undertaken with a lumped-parameter method based on the analogy of the fluid system and mechanical system. A mathematical governing equation is then derived by integrating the fluid model with the mechanical model of the driving piston and piezoelectric actuator. Subsequently, in order to achieve a desired dispensing amount, control algorithm adjusting duty cycle of the driving voltage is synthesized and control responses are presented in time domain.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2006.11a
• /
• pp.428-433
• /
• 2006

This paper presents a new type of jetting dispenser for the integrated circuit(IC) fabrication and surface mount technology. The proposed system is featured by the piezoelectric actuator and hydraulic magnification device. After describing structural component of the dispensing mechanism and its operation principle, both the fluid modeling and the hydraulic magnification modeling are undertaken with a lumped-parameter method based on the analogy of the fluid system and mechanical system. A mathematical governing equation is then derived by integrating the fluid model with the mechanical model of the driving piston and piezoelectric actuator. Subsequently, in order to achieve a desired dispensing amount, control algorithm adjusting duty cycle of the driving voltage is synthesized and control responses are presented in time domain.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.8 no.1
• /
• pp.64-69
• /
• 2003

There exist the high frequency components, which can not be predicted by the low frequency model, due to the presence of sampling effect in current mode control. In this paper, the output voltage equations for the ZVS half bridge PWM convertor are derived from the steady state analysis, and the sampling gain presented in the current control loop is Investigated to improve the Prediction Performance of low frequency model of ZVS half bridge PWM converter.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2000.11a
• /
• pp.153-156
• /
• 2000

This paper presents an PID type fuzzy based method for nohnear engine idle controller The output is a duty cycle(DC) for driving a idle speed cont개l valve(1SCV). For precise control of SI engine, the CPS sensor and coolant temperature are used. Visual C* language is used to make simulation panel for the fast and precise idle speed control. The dSPACE board and supported Control desk program is used in experiment ta the same purpose as simulation. The experimental results have a good agreement with simulation ones.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2008.10a
• /
• pp.307-310
• /
• 2008

This paper is proposed the vector control of 3-phase induction motor drive system by photovoltaic generation. For performance of vector control using a current control voltage source inverter(CC-VSI). CC-VSI is controlled by torque and flux producing component of motor current, relating with current and voltage value of photovoltaic arrays at maximum power point that varies follow different level of insolation. The MPPT using a DC-DC converter controlled the duty cycle to track maximum power from PV under different insolation conditions. The simulation results are shown that the characteristics and performance of drive system, which varies as each conditions of light by expresses in voltage($V_{dq}$), current($I_{dq}$), speed of motor and torque.

• Proceedings of the KIEE Conference
• /
• 2003.07c
• /
• pp.1852-1854
• /
• 2003

In manufacturing processes, various and suitable pulse shapes are required for the purpose of material processing. In order to make various pulse shapes with variable pulse length and high duty cycle, We have fabricated the power supply consisting 6 SCRs and the Pulse Forming Network(PFN) with the precise delay time control. So our control system has three switching circuits, 3 mesh PFN, and simmer circuit. In addition, we have designed and fabricated the PIC one-chip microprocessor(16F877) to control the delay time of sequential switching.