• 한국추진공학회지
• /
• 제14권6호
• /
• pp.17-24
• /
• 2010

비충돌형 인젝터로부터 발생하는 액체추진제 분무의 준3차원 구조를 규명하기 위한 연구를 수행하였다. 인젝터 출구 근처에서의 분무 형상을 고속카메라를 사용하여 촬영하였고, 인젝터 분무에서 주기적 흘림현상이 관찰되었다. 또, 이중모드 위상도플러속도계(Dual-mode Phase Doppler Anemometry, DPDA)로 분무특성 매개변수(속도, 직경, 부피유속 등)를 측정하여 인젝터 분무의 공간분포 특성을 파악하였다. 본 실험은 분사압력 17.2~27.6 bar의 조건에서 분사축방향 및 확산방향 거리를 변화시키며 수행하였다.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2008년도 제30회 춘계학술대회논문집
• /
• pp.125-128
• /
• 2008

이중모드 위상도플러속도계(Dual-mode Phase Doppler Anemometry, DPDA)를 이용하여 소형 액체 로켓엔진 인젝터 분무의 미립화 특성을 고찰하였다. 분무액적의 반경방향 이동에 따른 속도, 크기, 수밀도, 부피플럭스 등을 다양한 분사압력에서 측정하여 인젝터 분무의 공간분포 특성을 규명한다. 분사 압력이 증가함에 따라 분무액적의 속도, 난류강도, 수밀도, 그리고 부피플럭스는 증가하지만, 산술평균 직경($D_{10}$)과 분무액적의 증발율에 대한 척도인 Sauter Mean Diameter($D_{32}$)로 표현되는 액적의 크기는 감소하였다. 또, 속도와 부피플럭스는 Sauter 평균직경(Sauter mean diameter, SMD)에 비례하는 것을 알 수 있었다.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2007년도 제29회 추계학술대회논문집
• /
• pp.135-138
• /
• 2007

액체추진제 추력기에 사용되는 인젝터 분무액적의 2차원 공간분포 특성을 이중모드 위상도플러속도계(dual-mode phase Doppler anemometry, DPDA) 기법을 적용하여 고찰하였다. 분무액적의 속도, 난류강도, Sauter 평균직경(Sauter mean diameter, SMD), 수밀도, 그리고 체적플럭스 등의 분무분열특성 매개변수 변이를 정량화 하여 인젝터 분무의 거시적 거동을 규명한다. 본 연구는 추력기의 성능특성 이해는 물론 새로운 추력기의 설계기반 구축에 기여할 수 있을 것이다.

• 소성∙가공
• /
• 제13권1호
• /
• pp.84-89
• /
• 2004

There is a growing interest to replace the commercial steels with non-heat treated steels, which does not involve the spheroidization and quenching-tempering treatment. However, Non-heat treated steels should satisfy high strength and good formability without performing heat treatment. Therefore, it is important to investigate optimum materials showing a good combination of strength and formability after the drawing process. In this study, Dual-Phase Steels were studied as candidate materials for non-heat treated steels, which have different martensite morphologies and volume fractions obtained through heat-treatment of intercritical quenching (IcQ), intermediate quenching (ImQ) and step quenching (SQ). The mechanical properties of DP steels were measured by tension and compression tests. Also, the cold formability of three DP steels which have similar tensile strength value was investigated by estimating the deformation resistance and the forming limit. The deformation resistance which is important factor in determining die life was estimated by calculating the deformation energy. And the forming limit was estimated by measuring the critical strain revealing crack initiation at the notch tip of the specimens.

• 한국가시화정보학회지
• /
• 제8권4호
• /
• pp.60-65
• /
• 2010

A focus is given to the breakup behavior of spray droplets issuing from a nonimpinging-type injector. The analysis has been carried out experimentally by means of the dual-mode phase Doppler anemometry (DPDA). Spray characteristic parameters in terms of axial velocity, mean diameter, velocity fluctuation, and span (width of the size distribution) of droplets are measured down the geometric axis of a nozzle orifice and on the plane normal to the spray stream with the injection pressure variations. As the injection pressure increases, the velocity and its fluctuation become higher, whereas the droplet sizes get smaller. It is also shown that the magnitudes of those parameters are smoothed out by dispersion when the droplets move downstream as well as outwardly. The atomization process is significantly influenced by the injection pressure rather than the traveling distance in the experimental condition presented.

• 열처리공학회지
• /
• 제17권5호
• /
• pp.283-292
• /
• 2004

The effects of the annealing parameters on microstructures were examined in a cold-rolled high strength steel containing 0.1% C, 0.5% Si, 1.5% Mn, and 0.04% Nb. It was impossible to avoid martensite in the microstructure even though the continuous annealing parameters were controlled. This indicates that the alloying elements such as silicon and manganese contributing to manganese equivalent($Mn_{eq}$) should be reduced to produce the ferrite-pearlite microstructure for the solid solution and precipitation hardened steel. It was found that a decrease in the rapid cooling temperature to $520^{\circ}C$ was effective to change the microstructure from ferrite-martensite to ferrite-pearlite-martensite. Typical dual-phase properties exhibiting a low yield ratio and a continuous yielding behavior were obtained when the rapid cooling temperature was in the range of $680^{\circ}C$ to $600^{\circ}C$. The critical volume fraction of martensite for the typical properties of dual-phase steel was about 11 percent.

• 한국항공우주학회지
• /
• 제32권9호
• /
• pp.130-135
• /
• 2004

본 논문은 국내 최초로 그레인의 형상을 조절하여 설계한 이중추력형 로켓 모터의 개발에 관하여 기술하였다. 저연소속도 저연 추친제의 조성 및 finocyl형 그레인을 이용한 로켓 모터의 설계와 연소시험 데이터의 분석/평가 결과를 상술하였다. 개발된 이중추력형 로켓 모터는 비행시험에 성공적으로 적용되어 유도탄의 성능향상에 크게 기여하였고, 개발 결과는 향후 유사한 로켓 모터의 개발에 유용하게 사용될 것이다.

• ETRI Journal
• /
• 제33권5호
• /
• pp.752-758
• /
• 2011

This paper presents a clock and data recovery circuit that supports dual data rates of 5.4 Gbps and 3.24 Gbps for DisplayPort v1.2 sink device. A quarter-rate linear phase detector (PD) is used in order to mitigate high speed circuit design effort. The proposed linear PD results in better jitter performance by increasing up and down pulse widths of the PD and removes dead-zone problem of charge pump circuit. A voltage-controlled oscillator is designed with a 'Mode' switching control for frequency selection. The measured RMS jitter of recovered clock signal is 2.92 ps, and the peak-to-peak jitter is 24.89 ps under $2^{31}-1$ bit-long pseudo-random bit sequence at the bitrate of 5.4 Gbps. The chip area is 1.0 mm${\times}$1.3 mm, and the power consumption is 117 mW from a 1.8 V supply using 0.18 ${\mu}m$ CMOS process.

• Corrosion Science and Technology
• /
• 제9권6호
• /
• pp.247-253
• /
• 2010

The characteristics of selective oxidation prior to hot-dip galvanizing with the annealing atmosphere dew point and chemical composition in dual-phase steels and their effect on the inhibition layer formation relevant to coating adhesion have been studied using a combination of electron microscopic and surface analytical techniques. The annealed and also galvanized samples of 3 kinds of Si/Mn ratios with varied amounts of Si addition were prepared by galvanizing simulator. The dew point was controlled at soaking temperature $800^{\circ}C$ in 15%$H_2$ -85%$N_2$ atmosphere. It was shown that good adhesion factors were mainly uniformity of oxide particle distribution of low number density and low Si/Mn ratio prior to hot-dip galvanizing. Their effect was the greatly reduced coating bare spots and the formation of uniform inhibition layer leading to good adhesion of Zn overlay. The mechanism of good adhesion is suggested by two processes: the formation of inhibition layer on the oxide free surface uncovered with no $SiO_2$-containing particles in particular, and the inhibition layer bridging of oxide particles. The growth of inhibition layer was enhanced markedly by the delayed reaction of Fe and Al with the increase of Si/Mn ratio.

• Journal of Power Electronics
• /
• 제18권1호
• /
• pp.45-55
• /
• 2018

It is usually difficult for dual-active-bridge (DAB) dc-dc converters to operate efficiently at light loads. This paper presents an in-depth analysis of a DAB with triple-phase-shift (TPS) control under the light load condition to overcome this problem. A kind of operating mode which is suitable for light load operation is analyzed in this paper. First, an analysis of the zero-voltage-switching (ZVS) constraints for the DAB converter has been carried out and a reasonable dead-band setting method has been proposed. Secondly, the basic operating characteristics of the converter are analyzed. Third, under the condition of satisfying the ZVS constraints, both the reactive power and the root mean square (RMS) value of the current are simultaneously minimized and a particle swarm optimization (PSO) algorithm is employed to analyze and solve this optimization problem. Lastly, both simulations and experiments are carried out to verify the effectiveness of the proposed method. The experimental results show that the converter can effectively achieve ZVS and improved efficiency.