• The Transactions of the Korean Institute of Power Electronics
• /
• v.26 no.3
• /
• pp.192-198
• /
• 2021

The battery's State of Health (SOH) is a critical parameter in the process of battery use, as it represents the Remaining Useful Life (RUL) of the battery. Electrochemical Impedance Spectroscopy (EIS) is a widely used technique in observing the state of the battery. The measured impedance at certain frequencies can be used to evaluate the state of the battery, as it is intimately tied to the underlying chemical reactions. In this work, a low-cost portable EIS instrument is developed on the basis of the ARM Cortex-M4 Microcontroller Unit (MCU) for measuring the impedance spectrum of Li-ion battery packs. The MCU uses a built-in DAC module to generate the sinusoidal sweep perturbation signal. Moreover, it performs the dual-channel acquisition of voltage and current signals, calculates impedance using a Digital Lock-in Amplifier (DLA), and transmits the result to a PC. By using LabVIEW, an interface was developed with the real-time display of the EIS information. The developed instrument was suitable for measuring the impedance spectrum of the battery pack up to 1000 V. The measurement frequency range of the instrument was from 1 hz to 1 Khz. Then, to prove the performance of the developed system, the impedance of a Samsung SM3 battery pack and a Bexel pouch module were measured and compared with those obtained by the commercial instrument.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.46 no.8
• /
• pp.95-101
• /
• 2009

Random numbers are used in many sorts of applications. Some applications, like simple software simulation tests, communication protocol verifications, cryptography verification and so forth, need various levels of randomness with various process speeds. In this paper, we propose a fast pseudorandom generator module for embedded systems. The generator module is implemented in hardware which can run in two modes, one of which can generate random numbers with higher randomness but which requires six cycles, the other providing its result within one cycle but with less randomness. An ASIP (Application Specific Instruction set Processor) was designed to implement the proposed pseudorandom generator instruction sets. We designed a processor based on the MIPS architecture,, by using LISA, and have run statistical tests passing the sequence of the Diehard test suite. The HDL models of the processor were generated using CoWare's Processor Designer and synthesized into the Dong-bu 0.18um CMOS cell library using the Synopsys Design Compiler. With the proposed pseudorandom generator module, random number generation performance was 239% faster than software model, but the area increased only 2.0% of the proposed ASIP.

• Proceedings of the KIEE Conference
• /
• 2006.04b
• /
• pp.386-389
• /
• 2006

BIPV(Building Integrated PV) system can expect dual effects that reduce expenses for establishment of PV system by adding new function as outer covering material of building expect producing the electricity. In case of PV(photovoltaic system) there are many generation differences according to the exterior environmental facts(solar cell array, design and installation condition of interactive inverter system). In this paper, we compared constitute factors of 3kW BIPV(solar cell module, inverter), operating characteristic and total system characteristic(utilization, generation efficiency, loss fact) and found out long time operating data using a watch instrumentations. By use of long time operating result, compare a totally operating characteristics, and we proposed a next building application of BIPV. BIPV system that is proposed in this paper, was established in Solar Energy research center of Chosun University, composed with system. The objective of this paper, is to provide a efficient BIPV design method through the considerations for the integration of PV system.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.8 no.7
• /
• pp.1553-1557
• /
• 2004

A real-time processing system for embedded hardware genetic algorithm is suggested. In order to operate basic module of genetic algorithm in parallel, such as selection, crossover, mutation and evaluation, dual processors based architecture is implemented. The system consists of two Xscale processors and two FPGA with evolvable hardware, which enables to process genetic algorithm efficiently by distributing the computational load of hardware genetic algorithm to each processors equally. The hardware genetic algorithm runs on Linux OS and the resulted chromosome is executed on evolvable hardware in FPGA. Furthermore, the suggested architecture can be extended easily for a couple of connected processors in serial, making it accelerate to compute a real-time hardware genetic algorithm. To investigate the effect of proposed approach, performance comparisons is experimented for an typical computation of genetic algorithm.

• Journal of Information Processing Systems
• /
• v.15 no.1
• /
• pp.151-158
• /
• 2019

With the recent advances of memory technologies, high-performance non-volatile memories such as non-volatile dual in-line memory module (NVDIMM) have begun to be used as an addition or an alternative to server-side storages. When these memory bus-connected storages (MBSs) are installed over non-uniform memory access (NUMA) servers, the distance between NUMA nodes and MBSs is one of the crucial factors that influence file processing performance, because the access latency of a NUMA system varies depending on its distance from the NUMA nodes. This paper presents the design and implementation of a high-performance logical volume manager for MBSs, called MBS-LVM, when multiple MBSs are scattered over a NUMA server. The MBS-LVM consolidates the address space of each MBS into a single global address space and dynamically utilizes storage spaces such that each thread can access an MBS with the lowest latency possible. We implemented the MBS-LVM in the Linux kernel and evaluated its performance by porting it over the tmpfs, a memory-based file system widely used in Linux. The results of the benchmarking show that the write performance of the tmpfs using MBS-LVM has been improved by up to twenty times against the original tmpfs over a NUMA server with four nodes.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.27 no.6
• /
• pp.498-506
• /
• 2022

This study proposes a design methodology for bidirectional, series-resonant, dual-active bridge (SRDAB) converters. The circuit parameters of the SRDAB converters are designed by considering the output power and efficiency of the converter. The proposed method can be used to design a high-power, high-efficiency SRDAB converter. A voltage controller is employed to manipulate the output voltage of the converter, and the controller gains are selected using the transfer function and frequency response of the controller. Simulation results show that the output power of the designed SRDAB converter is 2 kW per converter module as designed. In addition, the performance of the voltage controller is evaluated using the simulation and experimental results. The output voltage follows the reference voltage within 10 ms under the step change of the reference command. The output voltage also follows the reference voltage under the step load change. The efficiency of the designed SRDAB converter is 95.6%.

• Journal of the Korea Society of Computer and Information
• /
• v.18 no.12
• /
• pp.1-9
• /
• 2013

Even though the multiple pages TLB are effective in improving the performance, a conventional method with OS support cannot utilize multiple page sizes in user application. Thus, we propose a new multiple-TLB structure supporting multiple page sizes for high performance and low power consumption without any operating system support. The proposed TLB is organised as two parts of a S-TLB(Small TLB) with a small page size and a L-TLB(Large TLB) with a large page size. Both are designed as fully associative bank structures. The S-TLB stores small pages are evicted from the L-TLB, and the L-TLB stores large pages including a small page generated by the CPU. Each one bank module of S-TLB and L-TLB can be selectively accessed base on particular one and two bits of the virtual address generated from CPU, respectively. Energy savings are achieved by reducing the number of entries accessed at a time. Also, this paper proposed the simple 1-bit LRU policy to improve the performance. The proposed LRU policy can present recently referenced block by using an additional one bit of each entry on TLBs. This method can simply select a least recently used page from the L-TLB. According to the simulation results, the proposed TLB can reduce Energy * Delay by about 76%, 57%, and 6% compared with a fully associative TLB, a ARM TLB, and a Dual TLB, respectively.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.17 no.5 s.108
• /
• pp.461-475
• /
• 2006

In this paper, it is described about the tri-band mobile antenna system design to provide broadband multimedia and direct broadcasting services using goo-stationary Koreasat 3, simultaneously operated in Ka/K/Ku band. The radiating part of the antenna system with a fan beam characteristic in the elevation plane is composed of the quasi-offset dual shaped reflector and the tri-band feeder. The tri-band feeder is also composed of the Ka/K dual band feeder with the protruding dielectric rod, the circular polarizer, the ortho-mode transducer and the circular-polarized Ku band feed array. Especially, the Ka/K dual band circular polarizer was realized firstly using the comb-type structure. For fast satellite-tracking on the movement, the Ku band feed array has the structure of the $2{\times}2$ active phased array which can make electrical beams. And, the circular-polarized characteristic in the feed array was improved by $90^{\circ}$ rotating arrangement of four radiating elements polarized circularly by a $90^{\circ}$ hybrid coupler, respectively. Four beam forming channels to make electrical beams at Ku band are divided into the main beam channel and the tracking beam channel in the output, and noise temperature characteristics of each channel were analyzed on the basis of the contributions of internal sub_units. From the fabricated antenna system, the output power at $P_{1dBc}$ of Ka_Tx channel was measured more than 34.1 dBm and the measured noise figures of K/Ku_Rx channels were less than 2.4 dB and 1.5 dB, respectively, over the operating band. The radiation patterns with co- and cross-polarization in the tri-band were measured using a near-field measurement in the anechoic chamber. Especially, Ku radiation patterns were measured after correcting each initial phase of active channels with partial radiation patterns obtained from the independent excitation of each channel. The antenna gains measured in Ka/K/Ku band of the antenna system were more than 39.6 dBi, 37.5 dBi, 29.6 dBi, respectively. And, the antenna system showed good system performances such as Ka_Tx EIRP more than 43.7 dBW and K/Ku_Rx G/T more than 13.2 dB/K and 7.12 dB/K, respectively.

• Nuclear Engineering and Technology
• /
• v.46 no.4
• /
• pp.547-556
• /
• 2014

Korea expects a shortage in storage capacity for spent fuels at reactor sites. Therefore, a need for more metal and/or concrete casks for storage systems is anticipated for either the reactor site or away from the reactor for interim storage. For the purpose of interim storage and transportation, a dual purpose metal cask that can load 21 spent fuel assemblies is being developed by Korea Radioactive Waste Management Corporation (KRMC) in Korea. At first the gamma and neutron flux for the design basis fuel were determined assuming in-core environment (the temperature, pressure, etc. of the moderator, boron, cladding, $UO_2$ pellets) in which the design basis fuel is loaded, as input data. The evaluation simulated burnup up to 45,000 MWD/MTU and decay during ten years of cooling using the SAS2H/OGIGEN-S module of the SCALE5.1 system. The results from the source term evaluation were used as input data for the final shielding evaluation utilizing the MCNP Code, which yielded the effective dose rate. The design of the cask is based on the safety requirements for normal storage conditions under 10 CFR Part 72. A radiation shielding analysis of the metal storage cask optimized for loading 21 design basis fuels was performed for two cases; one for a single cask and the other for a $2{\times}10$ cask array. For the single cask, dose rates at the external surface of the metal cask, 1m and 2m away from the cask surface, were evaluated. For the $2{\times}10$ cask array, dose rates at the center point of the array and at the center of the casks' height were evaluated. The results of the shielding analysis for the single cask show that dose rates were considerably higher at the lower side (from the bottom of the cask to the bottom of the neutron shielding) of the cask, at over 2mSv/hr at the external surface of the cask. However, this is not considered to be a significant issue since additional shielding will be installed at the storage facility. The shielding analysis results for the $2{\times}10$ cask array showed exponential decrease with distance off the sources. The controlled area boundary was calculated to be approximately 280m from the array, with a dose rate of 25mrem/yr. Actual dose rates within the controlled area boundary will be lower than 25mrem/yr, due to the decay of radioactivity of spent fuel in storage.

• Bulletin of the Korean Space Science Society
• /
• 2003.10a
• /
• pp.63-63
• /
• 2003

There are many actuators and sensors used for attitude control system for KOMPSAT such as Reaction Wheel Assembly, Magnetic Torque Assembly, Dual Thruster Module, Solar array Drive, Three Axis Magnetometer, Conical Earth Sensor, Fine Sun Sensor Assembly, Coarse Sun Sensor Assembly, Gyro Reference Assembly and so on. For KOMPSA T satellite it has been considered using the Magnetic Torquer (MTQ) generating the magnetic dipole moment. In general, the magnetic dipole moment for satellite attitude control system is used for dumping out the excessive reaction wheel momentum so that the reaction wheel speed is not saturated. The objective of this study is to analyze the magnetic field characteristics generated by the Magnetic Torquer using the Maxwell 2D Field Simulator software. Currently, the developing model (DM) of the MTQ is being developed and manufactured at a company under the supervision of KARL MTQ is an electromagnet consisting of a ferromagnetic cylindrical core on which an excitation coil is wound. A current is passed through the coil to produce a dipole momentum in the ferromagnetic core. The configuration of the MTQ will be introduced in the presentation. The 2 dimensional model of the MTQ is drawn as axisymmetric models in RZ plane, and each corresponding material is assigned to the each MTQ object, the core, coil, and background. After the boundary conditions, current sources, and solution parameters are set up, the magnetic field intensities, directions, and other values specified by users can be calculated by using the finite element analysis. The theoretical magnetic field quantities obtained by the Maxwell 2D Simulator can be used for the basis of the development of the MTQ.