• 한국세라믹학회지
• /
• 제30권9호
• /
• pp.775-783
• /
• 1993

TiO2-SiO2 system anti-reflective(AR) film was prepared to decrease reflectance on the glass surface. The experiments were carried out as fellow, 1) preparation & hydrolysis of TiO2-SiO2 system sols. 2) glass dipping, and 3) drying & heat treatment. We investigated the refractive index and thickness of film with viscosity, zeta-potential of sol, sol concentration, withdrawal speed, drying and heat treatment condition. As a result, we prepared good qualitative Quarter-Half-Quarter type anti-reflective film that had minimum, 0.02% and average reflectance, 0.087% in the visible region.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2016년도 추계 학술논문 발표대회
• /
• pp.83-84
• /
• 2016

Surplus water inside a concrete other than moisture that is used for hydration of the cement affects the physical properties of the concrete (modulus of elasticity, compressive strength, drying shrinkage, and creep) by drying. Changes in temperature and humidity inside a concrete has correlation with the movement speed and reaction rate of deterioration factors such as carbon dioxide and chloride ions. In this study, comparison was performed between temperature and relative humidity inside the concrete and meteorological data for exposure environment through measurement at the site for two years. Surface temperature of the concrete (depth 1cm) was measured higher by 6℃ during the summers, while it was measured lower by 2℃ during the winters due to solar radiation, wind, and radiation cooling. As for relative humidity, change was large in the depth of 1cm, while more than 85% was maintained in the depth of 10cm.

• 생명과학회지
• /
• 제12권5호
• /
• pp.535-543
• /
• 2002

해파리 반건품의 제조를 위한 최적 냉풍건조조건을 구하고 이 조건에서 제조한 제품의 저장성을 검토한 결과, 해파리 반건품의 제조를 위해서는 시중에서 구입한 염장해 파리를 냉수에서 침지액을 교환하면서 3분씩 3회 박박 문질러서 수세한 다음 $25^{\circ}C$에서 90분간 건조하는 것이 가장 양호하였다. 또한 이 조건에서 제조한 제품을 적층필름포 장지 (Ny/PE/LLDPE 0.015/0.04s/0.040 mm)로써 각각 함기포장 및 진공포장하고 6주 동안 각각 4$^{\circ}C$ 및 2$0^{\circ}C$에서 저장하면서 제품의 저장성을 실험한 결과 4$^{\circ}C$ 저장의 경우 진공포장시료에서는 6주까지 전체의 저장기간을 통하여 품질이 양호하였으나 함기포장시료에서는 저장 4주까지 품질이 양호하였으며 5주째부터는 품질이 크게 떨어졌다. 2$0^{\circ}C$ 저장에서는 진공포장 및 함기포장시료 모두 포장방법에 관계 없이 저장 3주까지는 품질이 양호하였으나 저장 4주째부터는 모두 품질이 불량한 것으로 나타났다.

• 한국가정과학회지
• /
• 제5권1호
• /
• pp.62-70
• /
• 2002

The objective of this study was to evaluate the effects of processing parameters of co-rotating twin screw extruder and dry methods on the level of resistant starch (RS) and the properties of extrudate prepared from normal maize starch. The processing parameters were used 90, 110, 130$^{\circ}C$ in temperature, 25.0~30.0% in moisture content, 150, 200, 250 rpm in screw speed and hot and cool air drying and drying after refrigerating in drying methods. The barrel temperature and drying methods had affected the level of resistant starch of extrudate. RS levels of extrudates were ranged from 2.4 to 15.5% by AOAC method. The extrudates, extruded at 110$^{\circ}C$ and then stored at 4$^{\circ}C$, showed the highest level of RS level (15.5%). Water absorption index increased with increasing moisture content and peak temperatures and viscosities of extudates decreased compare to that of raw starch from 94$^{\circ}C$ to 50~65$^{\circ}C$ and from 220 to 46~98 RVU, respectively. Extudates treated in 90$^{\circ}C$ and 110$^{\circ}C$ showed strong peak at $2{\theta}=6.7{\sim}17.0^{\circ}$ by X-ray diffractometry and had ~150$^{\circ}C$ endotherm like as that of RS3 starch by differential scanning calorimetry. In case of 130$^{\circ}C$, extrudates showed strong peak at $2{\theta}=20.0^{\circ}$ and had 106$^{\circ}C$ endotherm.

• 한국안전학회지
• /
• 제27권5호
• /
• pp.211-218
• /
• 2012

Two experiment are planed to identify driver's safe driving behaviour by curve radius, road surface condition in curve section. At four-lane and two-lane road, conducted experiments are check on driver's feeling of safety that 30 subjects do not feel discomfort. And using the data from these experiments, this study compare physical speed (not slipping, fall our of the road) with safety driving speed(drivers felt a comfortable and safe speed) each curve radius and fiver road surface condition(drying, wet, rain, snow and ice). As a result, safe driving behaviour factors that are derived to curve radius of 100m units, five road surface conditions enable to represent quantitative analysis of driver's discomfort. This study will develop road design method and evaluation reflected ergonomic aspects.

• 한국염색가공학회지
• /
• 제8권6호
• /
• pp.47-54
• /
• 1996

In order to develop the air flow finishing machine with low tension drying and surface modification by high impact effect, the treatment characteristics and the moving speed of fabrics was analysed and investigated in the newly developed system. The change of handle before and after treatment of fabrics measured using Kawabata system. The moving speed in air nozzle was affected by an air pressure of blower, and the maximum value was 1,000 m/min. In accordance with the change of handle, the treatment effect was very different compared with untreated fabrics. And the drape properties of fabrics increased about 10∼45% compared with untreated one.

• Journal of Biosystems Engineering
• /
• 제27권6호
• /
• pp.513-520
• /
• 2002

A 5-row walking garlic harvester with pulling mechanism was developed in the study, based upon a kinematical analysis and related preliminary field tests on the conventional garlic harvesting method. The harvesting efficiency of the developed harvester was more than 98% in the garlic field irrigated before harvesting, 80-85% in the field without irrigation. The harvesting performance of the harvester was 660∼825㎡/hr at the forward speed of harvester of 0.3m/s in the irrigated field before garlic harvesting. For proper garlic drying and collection, the harvester discharged the harvested garlic on the ground uniformly at the angles of 135。∼150。 to its forward direction with the garlic bulb's placing toward the harvester. In the field tests, it was recommended that the forward speed of the harvester be approximately less than 0.2m/s, and that the spacing of planting garlic seeds should be standardized in the future fur increasing its harvesting efficiency.

• 한국축산식품학회지
• /
• 제30권2호
• /
• pp.277-285
• /
• 2010

경제적 가치가 낮은 노계육으로 겨울철의 자연 동결 건조에 의해 새로운 염지 건조 계육을 제조하기 위하여 본 연구를 실시하였다. 평균 80주령의 산란 노계 통닭을 무처리(대조구), 염지구, 염지에 2% trehalose 첨가구로 나누어 실시하였다. 시험용 노계육은 강원도 인제에서 겨울철 3개월(2008. 1-2008. 3; 평균기온: $-1.8^{\circ}C$; 평균습도: 63%; 평균풍속: 1.8 m/sec) 동안 명태 건조와 동일한 방법으로 야외에서 건조시켰다. 건조가 진행됨에 따라 노계육의 수분과 수분활성도는 모두 감소하였다. 특히 염지 처리를 하면 건조기간 중 대조구에 비해 pH가 높고 수분활성도와 전단력이 낮으며, 지방산화와 단백질 부패가 억제되었다(p<0.05). 관능검사에서도 염지시킨 건조 노계육이 대조구에 비해 맛, 연도, 다즙성 및 종합적 기호도에서 월등히 우수하였다(p<0.05). Trehalose는 염지육에서 건조기간 중상대적으로 수분 함량을 높이고 건조를 지연시켰으나, 수분활성도는 대조구에 비해 낮췄기(p<0.05) 때문에 보습제의 역할을 하였다. 지방산 조성을 보면 건조기간 동안 염지육들이 대조구에 비해 다가불포화지방산 함량이 높았다. 대부분의 미생물들은 건조 중에 약 2 Log CFU/g 이하의 낮은 수준이거나 검출되지 않았다. 따라서 이화학적, 미생물학적 및 관능검사의 결과로 볼 때 노계육을 염지시켜 자연 건조를 3개월 이내 실시하면 품질 및 위생적으로 문제가 없는 건조 노계 육제품을 제조할 수 있다.

• 한국초지조사료학회지
• /
• 제42권2호
• /
• pp.73-78
• /
• 2022

본 시험은 우리나라에서 인공건초 조제 기술을 확보를 위해 수행되었다. 원적외선 히터를 활용하여 온도, 송풍량, 원적외선 방사량을 조절할 수 있는 기기를 제작하여 4차 수확한 알팔파를 대상으로 실시하였다. 건조를 위한 조건은 전체 4개의 조건을 선택하여 수행하였으며 각각의 조건은 방사율은 40% 내외(33-42%)로 설정을 하여 복합 조건에서는 시간이 지날수록 방사율을 낮추었다. 온도는 58~65℃로 설정하였으며, 기기내의 기류의 속도는 60m/s로 고정하였다. 전체적인 건조시간은 단일조건에서는 30분, 복합조건은 60분(30-30분) 및 90분(30-30-30분)으로 설정하여 시간대별로 방사율과 온도에 변화를 주었다. 건조 조건 1 (30분건조)의 경우에는 최종 건물함량이 46.26%로 건초에 적합한 건물에는 도달하지 못하였다. 그러나 나머지 2~7번 건조 조건에 해당하는 알팔파는 모두 건물함량이 80% 이상으로 나타나 최적의 알팔파 건초가 생산되었다. 건조 조건에 따른 전력 소비량의 차이를 보면 2번 건조조건에서 4.7 KW로 가장 낮게 나타났으며 나머지 건조조건은 6.5~7.1KW로 높았다. 조단백질 함량은 평균 25.91%로 높게 나타났으며 수확 당시(23.39%)보다 전체적인 함량은 높아졌다. 또한 5번 건조 조건에서 가장 높은 함량을 나타내었으며(26.93%) 6번 건조 조건에서 가장 낮은 값을 나타내었다(25.16%). 소화율은 평균 84.90%로 높은 값을 나타내었으며 처리간에 유의적인 차이를 나타내지 않았다(p>0.05). TDN 함량은 ADF 함량을 기반으로 하여 계산된 수치로 전체적인 경향은 ADF 함량과 비슷하였으며 원적외선 건조 조건에서 대체로 높은 경향을 보여주었다. 한편 4차 예취한 알팔파 건초의 RFV 값은 평균 166으로 높았으며 열풍건조 조건에서 유의적으로 낮았으며 원적외선 건조 조건에서는 큰 차이가 없었다. 이상의 결과를 종합하여 볼 때 2번 건조조건이 가장 유리한 것으로 판단되었다.

• 한국의류산업학회지
• /
• 제16권3호
• /
• pp.421-433
• /
• 2014

The aim of this study was to provide compression wear manufacture brands with information needed for product development. 8 tops and 7 bottoms from widely recognized compression wear manufacture brands were selected, and their product structural elements were analyzed, too. The results showed that most compression wear designs were applications of cutting lines designed considering muscle movements of the human body. The average number of cutting lines for patterns and designs were 14 for tops and 15 for bottoms. Different colored material was mainly used on the top for areas that require ventilation or high movement during sports for tops, and for areas that require muscle and joint support during sports for bottoms. The functionality of top materials were found to be stretch, muscle support, moisture absorption and high speed drying, warmth and ventilation for tops, in order of frequency, and stretch, muscle support, moisture absorption and high speed drying, and pressure for bottoms, in order of frequency. Tops were cut in the direction of the lengthwise grain, and bottoms were not only cut in the direction of the lengthwise grain, but also in the direction of the crosswise grain and bias for many products. Tops consisted of an average of 13 organically connected panels, and bottoms consisted of an average of 18 organically connected panels, which was analyzed to improve functionality. The average clothing surface area stretch rate was 85.7% for tops and 70.0% for bottoms, indicating that bottoms were designed to have higher strain rates compared to tops.