• Journal of the Korean Ceramic Society
• /
• v.30 no.9
• /
• pp.775-783
• /
• 1993

TiO2-SiO2 system anti-reflective(AR) film was prepared to decrease reflectance on the glass surface. The experiments were carried out as fellow, 1) preparation & hydrolysis of TiO2-SiO2 system sols. 2) glass dipping, and 3) drying & heat treatment. We investigated the refractive index and thickness of film with viscosity, zeta-potential of sol, sol concentration, withdrawal speed, drying and heat treatment condition. As a result, we prepared good qualitative Quarter-Half-Quarter type anti-reflective film that had minimum, 0.02% and average reflectance, 0.087% in the visible region.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2016.10a
• /
• pp.83-84
• /
• 2016

Surplus water inside a concrete other than moisture that is used for hydration of the cement affects the physical properties of the concrete (modulus of elasticity, compressive strength, drying shrinkage, and creep) by drying. Changes in temperature and humidity inside a concrete has correlation with the movement speed and reaction rate of deterioration factors such as carbon dioxide and chloride ions. In this study, comparison was performed between temperature and relative humidity inside the concrete and meteorological data for exposure environment through measurement at the site for two years. Surface temperature of the concrete (depth 1cm) was measured higher by 6℃ during the summers, while it was measured lower by 2℃ during the winters due to solar radiation, wind, and radiation cooling. As for relative humidity, change was large in the depth of 1cm, while more than 85% was maintained in the depth of 10cm.

• Journal of Life Science
• /
• v.12 no.5
• /
• pp.535-543
• /
• 2002

To investigate the possibility of processing semi-dried jellyfish and to examine its keeping quality, the factors such as moisture content, pH, volatile basic nitrogen (VBN), viable cell counts, color value and texture were analyzed. For processing of the semi-dried product, optimum conditions of drying temperature and drying time were $25^{\circ}C$ and 90min, respectively, under 60 $\pm$ 5% of relative humidity and 2 m/sec of air blast speed. The shelf-life of the products, vacuum-packing method in nylon/polyethylene/linear low density polyethylene (0.015/0.045/0.040 mm) laminated film bag was at least 6 weeks during storage at 4$^{\circ}C$, while that of air packaged one was at least 4 weeks. In case of 2$0^{\circ}C$ storage the shelf-life of the products was at least 3 weeks in both air and vacuum packaged ones.

• Korean Journal of Human Ecology
• /
• v.5 no.1
• /
• pp.62-70
• /
• 2002

The objective of this study was to evaluate the effects of processing parameters of co-rotating twin screw extruder and dry methods on the level of resistant starch (RS) and the properties of extrudate prepared from normal maize starch. The processing parameters were used 90, 110, 130$^{\circ}C$ in temperature, 25.0~30.0% in moisture content, 150, 200, 250 rpm in screw speed and hot and cool air drying and drying after refrigerating in drying methods. The barrel temperature and drying methods had affected the level of resistant starch of extrudate. RS levels of extrudates were ranged from 2.4 to 15.5% by AOAC method. The extrudates, extruded at 110$^{\circ}C$ and then stored at 4$^{\circ}C$, showed the highest level of RS level (15.5%). Water absorption index increased with increasing moisture content and peak temperatures and viscosities of extudates decreased compare to that of raw starch from 94$^{\circ}C$ to 50~65$^{\circ}C$ and from 220 to 46~98 RVU, respectively. Extudates treated in 90$^{\circ}C$ and 110$^{\circ}C$ showed strong peak at $2{\theta}=6.7{\sim}17.0^{\circ}$ by X-ray diffractometry and had ~150$^{\circ}C$ endotherm like as that of RS3 starch by differential scanning calorimetry. In case of 130$^{\circ}C$, extrudates showed strong peak at $2{\theta}=20.0^{\circ}$ and had 106$^{\circ}C$ endotherm.

• Journal of the Korean Society of Safety
• /
• v.27 no.5
• /
• pp.211-218
• /
• 2012

Two experiment are planed to identify driver's safe driving behaviour by curve radius, road surface condition in curve section. At four-lane and two-lane road, conducted experiments are check on driver's feeling of safety that 30 subjects do not feel discomfort. And using the data from these experiments, this study compare physical speed (not slipping, fall our of the road) with safety driving speed(drivers felt a comfortable and safe speed) each curve radius and fiver road surface condition(drying, wet, rain, snow and ice). As a result, safe driving behaviour factors that are derived to curve radius of 100m units, five road surface conditions enable to represent quantitative analysis of driver's discomfort. This study will develop road design method and evaluation reflected ergonomic aspects.

• Textile Coloration and Finishing
• /
• v.8 no.6
• /
• pp.47-54
• /
• 1996

In order to develop the air flow finishing machine with low tension drying and surface modification by high impact effect, the treatment characteristics and the moving speed of fabrics was analysed and investigated in the newly developed system. The change of handle before and after treatment of fabrics measured using Kawabata system. The moving speed in air nozzle was affected by an air pressure of blower, and the maximum value was 1,000 m/min. In accordance with the change of handle, the treatment effect was very different compared with untreated fabrics. And the drape properties of fabrics increased about 10∼45% compared with untreated one.

• Journal of Biosystems Engineering
• /
• v.27 no.6
• /
• pp.513-520
• /
• 2002

A 5-row walking garlic harvester with pulling mechanism was developed in the study, based upon a kinematical analysis and related preliminary field tests on the conventional garlic harvesting method. The harvesting efficiency of the developed harvester was more than 98% in the garlic field irrigated before harvesting, 80-85% in the field without irrigation. The harvesting performance of the harvester was 660∼825㎡/hr at the forward speed of harvester of 0.3m/s in the irrigated field before garlic harvesting. For proper garlic drying and collection, the harvester discharged the harvested garlic on the ground uniformly at the angles of 135。∼150。 to its forward direction with the garlic bulb's placing toward the harvester. In the field tests, it was recommended that the forward speed of the harvester be approximately less than 0.2m/s, and that the spacing of planting garlic seeds should be standardized in the future fur increasing its harvesting efficiency.

• Food Science of Animal Resources
• /
• v.30 no.2
• /
• pp.277-285
• /
• 2010

The objective of this study was to manufacture spent layer chicken meat products by natural freeze-drying. The spent layers of chickens that were slaughtered at 80 wk were obtained from a local slaughter house and separated into two halves of carcasses. The samples were divided into the following groups: 1) control (non-curing), 2) curing, and 3) curing with 2% trehalose before drying. The cured meats were placed at $2^{\circ}C$ for 7 d and then transferred to a natural drying spot located in Injae City, Gangwondo, Korea. The experiment was conducted from January to March in 2008. The average temperature, RH, and wind speed were $-1.5^{\circ}C$, 63%, and 1.8 m/sec, respectively. The cured treatments showed higher pH, lower Aw and lower shear force value compared with the control. Based on the results of TBARS (2-thiobarbituric acid reactive substances) level and volatile basic nitrogen value, lipid oxidation and protein deterioration were inhibited in curing treatments during drying. Trehalose acted as a humectant because it maintained a lower water activity despite the relatively higher moisture content during drying. The polyunsaturated fatty acids content and sensory attributes were higher in cured treatments than in the control during drying. Most of the bacterial counts in the treated groups were lower by 2 Log CFU/g after 1 mon of drying, and Salmonella spp. and Listeria spp. were not found in any treatment. There was also no microbial safety problem associated with dried meat products. Based on the results of this experiment, dried meat products could be manufactured from precured spent layer chickens by natural freeze-drying during winter.

• Journal of The Korean Society of Grassland and Forage Science
• /
• v.42 no.2
• /
• pp.73-78
• /
• 2022

This experiment was conducted to establish the technology for artificial hay preparation in Korea. Using far-infrared heater, a device that can control temperature, airflow, and far-infrared radiation was produced and conducted on the fourth harvested alfalfa. The drying conditions were carried out by selecting a total of four conditions. For each condition, the radiation rate was set to around 40% (33-42%), and the temperature was set at 58~65℃, and the speed of the airflow was fixed at 60m/s. The overall drying time was set to 30 min in the single and 60 min (30-30 min) and 90 min (30-30-30 min) in the complex condition, and the radiation rate and temperature were changed by time period. In the case of drying condition 1, the final dry matter (DM) content was 46.26%, which did not reach a DM suitable for hay. However, all of the alfalfa corresponding to the remaining drying conditions 2 to 7 showed a DM content of 80% or more, resulting in optimal alfalfa hay production. In power consumption according to the drying conditions, the second drying condition showed the lowest at 4.7 KW, and the remaining drying conditions were as high as 6.5 to 7.1 KW. The crude protein content was found to be high at an average of 25.91% and it showed the highest content in the 5th drying condition (26.93%) and the lowest value in the 6th drying condition (25.16%). The digestibility showed a high value with an average of 84.90%, and there was no significant difference among treatments (p>0.05). Considering the above results, it was judged that drying condition 2 was the most advantageous.

• Fashion & Textile Research Journal
• /
• v.16 no.3
• /
• pp.421-433
• /
• 2014

The aim of this study was to provide compression wear manufacture brands with information needed for product development. 8 tops and 7 bottoms from widely recognized compression wear manufacture brands were selected, and their product structural elements were analyzed, too. The results showed that most compression wear designs were applications of cutting lines designed considering muscle movements of the human body. The average number of cutting lines for patterns and designs were 14 for tops and 15 for bottoms. Different colored material was mainly used on the top for areas that require ventilation or high movement during sports for tops, and for areas that require muscle and joint support during sports for bottoms. The functionality of top materials were found to be stretch, muscle support, moisture absorption and high speed drying, warmth and ventilation for tops, in order of frequency, and stretch, muscle support, moisture absorption and high speed drying, and pressure for bottoms, in order of frequency. Tops were cut in the direction of the lengthwise grain, and bottoms were not only cut in the direction of the lengthwise grain, but also in the direction of the crosswise grain and bias for many products. Tops consisted of an average of 13 organically connected panels, and bottoms consisted of an average of 18 organically connected panels, which was analyzed to improve functionality. The average clothing surface area stretch rate was 85.7% for tops and 70.0% for bottoms, indicating that bottoms were designed to have higher strain rates compared to tops.