• Journal of the Korean Wood Science and Technology
• /
• v.35 no.1
• /
• pp.11-16
• /
• 2007

This study was carried out to investigate the effect of Vapor-dam treatment on drying drying rates, prevention of checks and V-shaped split during air circulating oven drying bamboo (Phyllostachys pubescens Mazel et Z) tube. It was shown that the drying time from green to around 7~8 % of moisture content was required less as drying schedule was more severe, and distinctly dominated by the drying rate during the initial drying stage. Area shrinkages in cross section and thickness shrinkages measured during air circulating oven drying test were very large. Surface checks and V-shaped splits were occurred in untreated samples just after the beginning of drying, while sixty seven percentages of all the Vapor-dam treated samples could be produced without drying defects. The V-shaped splits occurred in the Vapor-dam treated samples were influenced more by the sealing of the vapor evaporation through the cross section than drying schedule.

• Journal of the Korean Wood Science and Technology
• /
• v.27 no.4
• /
• pp.51-56
• /
• 1999

Finite element method was utilized to analyze crack tip stress and displacement field under drying stress case as stepwise loading. Opening mode of single-edge-notched model was employed and analyzed by linear elastic fracture mechanics of plane stress case. The drying stresses were applied as stepwise loads at the boundary elements of the model with 10 steps of time serial. The stress intensity factor($K_I$) for opening mode reached to its maximum just prior to the stress reversal. The $K_I$ from the displacement fields revealed 1.7 times higher than those from stress fields. By comparing the two sets of $K_I$ from displacement and stress fields, single parameter $K_I$ showed its validity to characterize displacement fields around the crack tip front while stress field could not be characterized due to large variations between two sets of data.

• Journal of the Korean Wood Science and Technology
• /
• v.21 no.2
• /
• pp.39-48
• /
• 1993

End-matched disks of 7.7cm thickness were part-time dried in vacuum press dryer to investigate the drying characteristics by using drying schedules and end treatments. The ginkgo disks could be dried faster with severer end checks and ring failures by C schedule than by S schedule. There were no significant differences in drying rates and amounts of end checks, ring failures and V-shaped checks occurred between ginkgo disks end-taped with Korean traditional paper (KTP) and those untreated. The drying time of walnut disks was slightly reduced by end-taping with KTP. And the length of end checks and V-shaped checks and the frequency of defected disk were decreased more effectively than those untreated. The tangential strains and tangential drying stresses near bark sides of ginkgo and walnut disk untreated were developed in the early stage of drying and incresed slightly curvi-linearly above fiber saturation point (fsp) and more curvi-linearly below fsp. The influence of end-taping with KTP on the drying rate for impermeable walnut disk was stronger than that for permeable ginkgo disk.

• Journal of the Korean Wood Science and Technology
• /
• v.35 no.1
• /
• pp.17-26
• /
• 2007

This study was conducted to investigate the effects of End-coating (CO) treatment and Vapor-dam (V) treatment on the air circulating oven drying characteristics of green stock (Paulownia tomentosa) for drum. The reduction of the weight of specimens was greatly displayed in order of control (C-NC) treatment, End-coating (C-CO) treatment, Vapor-dam (V-NC) treatment and Vapor-dam/End-coating (V-CO) treatment after the beginning of drying. The V-CO treated specimen showed smoother temperature gradient compared with the V-NC treated specimen throughout whole drying stage and there was little temperature gradient between the inner and outer part of the cylindrical stock. The C-CO treated specimen showed higher value of vapor pressure in both the inner and outer part of the cylindrical stock until the middle stage of drying, while after the middle stage of drying only the inner part of the cylindrical stock presented higher value compared with the C-NC treated specimen. The distribution of the absolute vapor pressure of the V-CO treated specimen was similar to that of the V-NC treated specimen during the initial stage of drying. However, the former showed a large distribution in order of the hollow, the outer part, the inner part of the cylindrical stock after the initial stage of drying, which was entirely different model of distribution from that of the V-NC treated specimen. Surface checks and ring failures were not observed for all of the specimens, while end checks were severely occurred for the C-NC treated specimen and the V-NC treated specimen.

• Journal of the Korean Wood Science and Technology
• /
• v.51 no.6
• /
• pp.493-508
• /
• 2023

Round timber materials of 600 mm length, cut from large-cross-section round timber of red pine (Pinus densiflora S. et Z.) of 450 mm width and 4.2 m length, were prepared as the target of kiln drying in this study. After treating the target materials through end sealing (ES), end sealing - kerfing (ES-K), lateral sealing - end sealing - boring (LS-ES-B), or lateral sealing - partial end sealing (LS-PES), the effects of the treatment on the incidence of drying defects were determined. The target materials with exposed lateral surface and sealed cross surface were steamed at the initial temperature of 65℃ above the official pest control temperature of 56℃, followed by kiln drying toward the final temperature of 75℃. The target materials with sealed lateral surfaces, on the other hand, were dried at the initial temperature of 90℃ at almost the maximum temperature of conventional kiln drying, as there is no risk of early check formation caused by surface moisture evaporation. The final temperature was set at approximately 100℃. The drying time, taken for the target materials with initial moisture content of 70%-80% to reach the target moisture content of 19%, varied across treatment conditions. The measured drying time was 1,146 hours (approximately 48 days) for the timber with sealed cross surface and 745 hours (approximately 31 days) for the timber with sealed lateral surface, until the moisture content reached the target level. The formation of surface checks could not be prevented in the control and ES groups, but a definite preventive effect was obtained for the LS-ES-B and LS-PES groups.

• Journal of the Korean Wood Science and Technology
• /
• v.15 no.2
• /
• pp.67-78
• /
• 1987

This study was designed to investigate the effect of board thickness and ring angle on the characteristics including internal check. ring failure, surface check, end check, collapse, thickness shrinkage and width shrinkage of press-drying. The exprimental materials of 6mm-. 9mm- and 12mm-thick board were taken from heartwood and sapwood of oak (Quercus acutissima Carr.) respectively. And boards were numbered according to position in the log(No. 1 to No. 4 for heartwood :md No. 9 for sapwood). Press-drying was at $145^{\circ}C$ platen temperature and 3.5kg/$Cm^2$ platen pressure. The results of this study were summarized as follows. 1. Drying rates for sapwood materials were greater than those for heartwood materials. And drying rates for thinner materials were greater than those for thicker materials. 2. The thinner boards were. the severer surface checking developed in the heartwood materials, and surface checking for heartwood materials had no tendency in board position for the same thickness. Sapwood materials were completely free from surface checking. 3. End checking for heartwood materials had no tendency in board position. The greater deviation of ring angle from perfectly edge-grained was, the severer and checking developed in the sapwood materials. But end checking did not occur in 6mm-thick sapwood materials. 4. The greater deviation of ring angle from perfectly edge-grained was, the severer end checking developed for heartwood and sapwood materials. As board thickness increased, maternal checking developed more severely for heartwood and sapweed materials. 5. For heartwood materials, ring failure, reduced with increasing deviation of ring angle from perfectly edge-grained except 12mm-thick material and showed no significant difference attributable to board thickness. Sapwood materials were completely free from ring failure. 6. For heartwood and sapwood materials, collapse was slight and showed no significant differences attributable to both board thickness and board position. 7. As deviation of ring angle from perfectly edge-grained increased, shrinkage of board thickness decreased for heartwood and sapwood materials. 8. Shrinkage of board width showed no significant differences attributable to both board thickness and board position for heartwood and sapweed materials.

• Journal of the Korean Wood Science and Technology
• /
• v.45 no.1
• /
• pp.107-115
• /
• 2017

In this study, the surface check reduction effect of preservative-treated Korean larch round-wood was investigated by applying three physical treatments, such as incising, kerfing, and kiln-drying. Moreover, the possibility of long-term service life was also checked by comparing the depth of surface check and the penetration depth of preservative. A rapid gradient of wood moisture content between surface and center causes a surface check. Thus, the effect of reducing surface check was carried out at the lowest equilibrium moisture content (EMC) condition, temperature ($2^{\circ}C$), humidity (44.6%), in outdoor locations in Korea until the test specimens reach to the 8.6% EMC. As a result, the preservative-treated specimens without incising, kerfing, kiln-drying (Type C) could not ensure the long-term service life due to a large surface check. Because the surface check depth of all specimens was deeper than the penetration depth of preservative. In case of the incising treated specimens (Type I), 80% of them, the depth of surface check was not deeper than the penetration depth of preservative. However, when a kerfing was additionally treated (Type B), a possibility of happening deeper surface check than penetration depth of preservative was increased rather than Type I.

• Journal of the Korean Wood Science and Technology
• /
• v.37 no.3
• /
• pp.231-238
• /
• 2009

Red pine (Pinus densiflora) has been used for structural wood members of Korean traditional residence (HANOK) and historic wooden structures. For these constructions, generally, natural drying has conducted for long time; however, unless drying is conducted sufficiently, it could cause several drying defects such as check or warping. Shrinkage changes of red pine species for small clear specimens and big-size specimens according to the conditions of moisture contents, were examined. For the estimation of volumetric shrinkage at a special moisture content, it was more precise to divide the range of moisture contents into two groups, green to air-dry and air-dry to oven-dry. The volumetric shrinkage had no difference with specimen sizes in sapwood, but decreased as specimen size increased in heartwood.

• Journal of the Korean Wood Science and Technology
• /
• v.31 no.4
• /
• pp.57-62
• /
• 2003

The Mechanical and drying characteristics of Pinus densiflora wood, which was damaged by forest fire, and sound wood were examined. There were no significant differences in axial compressive properties, shearing strength and impact bending absorbed energy between damaged and sound woods. But the bending properties of damaged wood were slightly higher than those of sound wood. The green moisture content of sapwood in damaged wood was lower than that in sound wood, but oven-drying rate was similar in both woods. Number of initial check in damaged wood was smaller than that in sound wood, and inner check in damaged and sound woods was not observed. Consequently, it is considered that mostly damaged wood by forest fire can be used for wood material after removing the bark.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.1849-1852
• /
• 2005

An automatic cap-washing machine is developed for rinse and dry of synthetic resin cap which is used in spring water bottle. This machine should be achieved all processes washing and drying, array, transfer automatically. A cap is washed by an ozonized water and pure water first. Next, a cap is dried by a hot wind drying equipment. In this paper, structural and modal analysis for the cap-washing machine is carried out to check the design criterion of the machine. The analysis is carried out by FEM simulation using the commercial software, CATIA V5. And a fictitious mass properties was used for the analysis of the machine. Finally, the machine performance is shown to be satisfactory.