• Journal of the Korean Wood Science and Technology
• /
• v.25 no.4
• /
• pp.51-60
• /
• 1997

We investigated the characteristics of air-and vacuum-drying heated by hot plates for 8~14cm-diameter logs or 6~12cm-thick pillars of Pinus koraiensis. And we evaluated the effects of longitudinal kerf and vacuum drying heated by hot plates. The vacuum drying times from green to 10.9~18.6% MC were 15 days, and these times were one-fifth compared to the air-drying times. The longitudinal kerfing had no significant, effect on drying rates during both air-drying and vacuum drying. But drying defects such as surface checks and V-shaped cracks were effectively prevented during air-drying and vacuum drying by longitudinal kerfing. The vacuum drying was more advantageous than air-drying for preventing of surface checks, end checks and V-shaped cracks, and especially, the vacuum dried pillars with longitudinal kerf were almost free from drying defects. In accelerated weathering conditions the resin did not exude for all specimens.

• Journal of the Korean Wood Science and Technology
• /
• v.30 no.4
• /
• pp.27-32
• /
• 2002

We investigated the effect of polyethylene glycol(PEG) treatment of preservative treated green japanese cedar(Cryptomeria japonica) round posts on their preservative penetration and check formation during the air drying. The round rods were dip-treated in 10% preservative solution of Basilit CFK for 1 day, followed by application(3, 5, and 10 times) with 50% PEG-400 solution, and then dried for 30 days under natural conditions. The rate of preservative penetration into sapwood was a low by 23.2% without PEG treatment, whereas that was a high by about 51.2~64.5% with PEG treatment. From these results, it was assumed that PEG played an affirmative role in the penetration of preservative components loaded onto the surface of round rods by dipping. During the air drying, the formation of drying checks decreased significantly with increasing application times of PEG. Even though some drying checks in PEG treated rods were developed, the number and size of checks was reduced remarkably by PEG treatment. After 2 months of outdoor exposure, PEG treatment failed to reduce checking in preservative-treated rods whereas finishing of polyurethane resin lacquer after PEG treatment was significantly effective in preventing check development.

• Journal of the Korean Wood Science and Technology
• /
• v.18 no.1
• /
• pp.39-51
• /
• 1990

This research was carried out to offer the basis data for development of optimum drying schedule for a domestic oak species (Quercus grosseserrata B1.) by investigating drying rate. stress, defect, and moisuture gradient with board thicknesses and drying schedules (code number T4-C2 and T3-B1). The results were obtained as follows: 1. Average drying rate and total drying time from 52.2% to 5.8% were 0.105%/hr and 486 hours for drying schedule T4-C2 and those from 62.1% to 8.3% were 0.070%/hr. and 811 hours for drying schedule T3-B1. 2. Drying rates for 28mm- and 31mm-thick boards showed similar tendency, but were significantly different from 25mm- thick board in drying schedule T4-C2 and those for 22mm-, 25mm- 28mm- and 31mm-thick boards showed similar tendency but were significantly different from 19mm- thick boards in drying schedule T3-B1. 3. The moisture gradients for drying schedule T4-C2 were steeper than those for drying schedule T3-B1 during drying period. and especially in early drying stage slow slope of moisture gradients of drying schedule T3-B1 was effective in preventing serious problem of surface checks. 4. Drying stresses were lower in drying schedule T3-B1 than in drying schedule T4-C2 during drying period. 5. Drying schedule T4-C2 was appropriate for 25mm-thick board but not for 28mm- and 31mm-thick board because of strong drying condition. Drying schedule T3-B1 was appropriate for 28mm- and 31 mm-thick board but not for 19mm-, 22mm-, and 25mm-thick board because of weak drying condition.

• Journal of the Korea Furniture Society
• /
• v.19 no.2
• /
• pp.116-123
• /
• 2008

Kiln schedule development was based on two schedule phases, the first being to determine the maximum safe kiln temperature during the check prone initial stage of drying, with the second stage determining how to accelerate drying once the danger of checking had passed. This was achieved by using 38 mm thick boards which were pre-screened for susceptibility to internal checking, and then drying matched sample boards over a range of kiln temperatures. Research has shown that below 50% MC there is no further risk of internal checking. However, difference in drying rate due to board width and the increased occurrence of wet patches in wide boards means that it is essential to modify the basic schedule according to the maximum board width. A condition of 52/40 $^{\circ}C$ was selected for the checking-free initial kiln drying step and a 5-step kiln-schedule dried the boards from 109% to 8% MC for 72.5 hours without internal checking.

• Journal of Computational Design and Engineering
• /
• v.3 no.4
• /
• pp.398-413
• /
• 2016

This work describes the design and development of a new drying system for a rollover carwash machine with the support of numerical tools. The drying system is composed of a pair of stationary vertical dryers and a moveable horizontal dryer that can adjust itself to the contour of a vehicle. After the definition of the dryers' concept, their performance was assessed individually to check their internal flow pattern and to improve their airflow distribution. These issues are expected to provide feedback on redesign and geometric optimization of the dryers. After redesign of the dryers separately, the behaviour of the complete drying system was studied on actual vehicle models, representative of the shortest and tallest dimensions that can be washed with the existing carwash machine sector. The drying efficiency of the whole system was studied by calculation of shear stress distribution on various surfaces of a given vehicle. The results allowed concluding that the overall drying performance of the design system is very good and assure adequate drying on most vehicles surfaces. The results obtained from numerical studies were then validated with experimental measurements and a good agreement was found between the two. The procedure employed in this work can be applied to support the design and analysis of other mechanical drying systems.

• Journal of the Korean Wood Science and Technology
• /
• v.15 no.2
• /
• pp.113-119
• /
• 1987

A study was conducted to determine the kiln drying schedule for hydrid aspen, This kiln drying schedule was found by oven drying method and developed by pilot testing of 2.0cm, 2.5cm, 3.0cm-thick green lumber. The results of this study were as follows: 1. Kiln drying schedule developed by oven-drying method was $T_{12}-E_5$ for 2.5cm-thick green lumber. 2. Drying times for 2.0cm-thick green lumber(127.0 percent moisture content) to 7.3 percent moisture content, for 2.5cm-thick green lumber(95.0 percent moisture content) to 9.7 percent moisture content, and for 3.0cm-thick green lumber(118.5 percent moisture content) to 10.0 percent moisture content were 45 hours, 45 hours, and 54 hours, respectively. 3. Drying rate from 90 to 10 percent moisture content of 2.5cm-thick lumber was about 0.7 times faster than that of 2.0cm-thick lumber and about 1.1 times faster than that of 3.0em-thick lumber. 4. End checks for 2.0cm-, 2.5cm-, and 3.0cm-thick green lumber occurred 95, 74 and 100 percent moisture content, respectively and reached maximum amount in 53, 41, and 60 percent moisture content, respectively. 5. No surface check and no honeycomb occurred. 6. Cupping and collapse slightly occurred and the quality of dry lumber was first.

• Journal of the Korean Wood Science and Technology
• /
• v.42 no.1
• /
• pp.49-57
• /
• 2014

The pre-air-drying of Korean pine before the high-temperature and low-humidity drying was shown to be effective in uniform moisture content distribution and prevention of surface check. Our results suggest that initial moisture content of the timber also plays important role in high-temperature and low-humidity drying method. The pre-air-drying also helps in the reduction of surface checks in Korean pine when compared to the Korean pine dried by only high-temperature and low-humidity. End-coating was not effective in the prevention of twist, shrinkage, case hardening and internal checks. The pre-air-drying reduces the internal tension stresses which occur during high-temperature and low-humidity drying thus decreasing case hardening and also preventing internal checks. The pre-air-drying decreases the moisture content and causes shrinkage which leads to increased twist in the Korean pine.

• Journal of the Korean Wood Science and Technology
• /
• v.48 no.3
• /
• pp.345-363
• /
• 2020

This study was conducted to identify the effect of kerfing and incising pretreatments on high-temperature drying characteristics of cedar and larch boxed-heart timbers with a cross section of less than 150 mm. The result showed that the pretreatments have made a significant difference regarding surface check and shrinkage. Although the kerfing was suitable as a pretreatment to reduce the occurrence of surface check, the incising was not suitable as a pretreatment since the knives of timber joined together, causing the conversion to the surface checks. The shrinkage showed a significant result that the final moisture content was reduced in the order of incising, kerfing, and kerfing-incising after the drying process based on the pretreatment condition. Twist was more affected by the grain angle than the anisotropy of the juvenile wood, and there was no effect of pretreatments.

• Journal of the Korean Wood Science and Technology
• /
• v.44 no.5
• /
• pp.677-684
• /
• 2016

This study was carried out to confirm the effects of the knife-incising and longitudinal kerfing treatment on high-temperature drying characteristics of red pine square timber with dimensions of thickness 15 cm. The range of final moisture content was investigated 5.6% to 7.5% after drying. The differences did not exist in the moisture content and distribution according to the pretreatment condition. In the case of longitudinal kerfing treatment, the surface check occurrence was reduced than the control. In addition, the twist had a tendency to decrease due to the longitudinal kerfing treatment. The knife-incising and longitudinal kerfing treatment were investigated to be ineffective on internal checks and drying shrinkage.

• Journal of the Korean Wood Science and Technology
• /
• v.21 no.3
• /
• pp.61-66
• /
• 1993

24mm-thick specimens from three species of plantation-grown softwood were press dried under two platen pressures of 1.75kgf/$cm^2$ and 3.50kgf/$cm^2$ to obtain drying information regarding to drying rate, thickness shrinkage and drying defects. The influence of platen pressure on drying fare in range of moisture content (30 to 10 percent) increased for pitch pine and larch, but reduced for korean white pine at higher pressure. Thickness shrinkage was increased at the higher pressure, and estimated thickness shrinkage at final MC of 10 percent became unrealistically greater for specimens containing higher final moisture content under the great influence of compressive strain. The effects of pressure on the amount of surface checks and honeycombing were different from species used. These species should have applied lower temperature than 177$^{\circ}C$ in this study to reduce surface checks and honeycombing.