• Journal of Forest and Environmental Science
• /
• 제11권1호
• /
• pp.50-60
• /
• 1995

낙엽송과 잣나무의 판재두께별 건조특성(乾操特性)을 파악코져 $100^{\circ}C$에서 급속건조(急速乾燥)를 실시하여 건조중 함수율(含水率)과 건조경과(乾操經過), 건조속도(乾操速度), 초기할렬(初期割裂), collapse, 내부할렬(內部割裂)등의 건조결함(乾操缺陷)을 조사하여 추정건조(推定乾操)스케쥴을 작성한 결과는 다음과 같다. 건조시간별(乾操時間別) 건조중(乾操中) 함수율(含水率)은 판재두께가 얇을수록 급속한 곡선적 감소(減少)를 나타내었고 함수율(含水率) 20%에서 낙엽송의 건조속도(乾操速度)는 잣나무재보다 크고, 판재두께가 두꺼울수록 적었다. 추정건조(推定乾操)스케쥴을 작성한 결과 닥엽송은 잣나무재에 비해 건조조건(乾操條件)을 완화하게 해야 하고 판재 두께가 두꺼운 5cm, 6cm에서는 건조초기(乾操初期)의 조건(條件)을 가장 완화하게 해야 함을 알 수 있었다.

• Journal of Forest and Environmental Science
• /
• 제12권1호
• /
• pp.1-12
• /
• 1996

강원도산(江原道産) 참나무과(科) 4수종(樹種)의 건조특성(乾操特性)을 파악코져 $100^{\circ}C$에서 급속건조(急速乾操)를 실시하여 건조중(乾操中) 함수율(含水率)과 건조경과(乾操經過), 초기할열(初期割裂)(목구할열(木口割裂)과 표면할열(表面割裂)), 찌그러짐, 내부할열(內部割裂) 등의 건조결함(乾操缺陷)을 조사하여 추정건조(推定乾操)스케쥴을 작성한 결과(結果)는 다음과 같다. 건조시간별(乾操時間別) 건조중(乾操中) 함수율(含水率)은 초기함수율(初期含水率)이 높은 판재일수록 급속(急速)한 곡선적(曲線的) 감소(減少)를 나타내었고 건조소요시간(乾操所要時間)은 두께가 두꺼울수록, 초기함수율(初期含水率)이 높을수록, 건조중(乾操中) 함수율(含水率) 변화( 變化)가 느린 수종(樹種)일수록 길었다. 또한, 두께가 두꺼울수록 할열(割裂)의 발생량(發生量)이 증가하므로 건조초기(乾操初期)의 조건(條件)을 완화하게 해야 함을 알 수 있었다.

• Journal of Forest and Environmental Science
• /
• 제10권1호
• /
• pp.38-48
• /
• 1994

강원도산(江原道産) 참나무과(科) 4수종(樹種)의 건조특성(乾燥特性)을 파악코져 $100^{\circ}C$에서 급속건조(急速乾燥)를 실시하여 건조중(乾燥中) 함수율(含水率)과 건조경과(乾燥經過), 초기할렬(初期割裂)(목구할렬(목구할렬(木口割裂))과 표면할렬(表面割裂)), 찌그러짐, 내부할렬(內部割裂) 등의 건조결함(乾燥缺陷)을 조사(調査)하여 추정건조(推定乾燥)스케쥴을 작성(作成)한 결과(結果)는 다음과 같다. 건조시간별(乾燥時間別) 건조중(乾燥中) 함수율(含水率)은 초기함수율(初期含水率)이 높은 판재(板材)일수록 급속(急速)한 곡선적(曲線的) 감소(減少)를 나타내었고 건조소요시간(乾燥所要時間)이 길었으며 굴참나무가 건조중(乾燥中) 할렬(割裂)의 발생량(發生量)이 가장 크게 나타났으며 구해진 추정건조(推定乾燥)스케쥴은 $T_5-C_2$였다. 또한 모든 수종(樹種)의 목리방향별(木理方向別) 수축율(收縮率)은 접선방향(接線方向)(T) > 방사방향(放射方向)(R) > 섬유방향(纖維方向)(L)의 순위(順位)였으며 급속건조법(急速乾燥法)에 의한 수축율(收縮率)이 정상적인 수축율(收縮率)보다 크게 나타났다.

• Journal of the Korean Wood Science and Technology
• /
• 제45권2호
• /
• pp.139-146
• /
• 2017

This study was conducted to develop a new drying technology in order to quickly and massively dry bamboo tubes without crack and check. The bamboo tubes with the diameter of 45 mm - 68 mm had been impregnated in the solution of PEG-1000, and then were dried under room temperature and high temperature, respectively. The cracks occurred on all control specimens while no cracks were found on PEG treated specimens during drying at room temperature due to effect of PEG restraining the circumferential shrinkage of bamboo tube. But the drying period of this method was too long (200 days) compared to 10 hours of kiln drying. During fast high temperature drying, cracks occurred on all control specimens, but no cracks were found on PEG treated specimens, which could be accounted for more solidified PEG due to higher drying temperature and faster drying rate, and the tension set formed on the surface of bamboo tube in the early stage of drying owning to high drying temperature and low relative humidity. Thus, it is advised that PEG treated bamboo tube should be fast dried at high temperature in order to not only prevent crack or check in short drying period but also increase the dimensional stability of the products made of bamboo tubes.

• Journal of the Korean Wood Science and Technology
• /
• 제48권2호
• /
• pp.121-135
• /
• 2020

본 연구에서는 대단면 목재의 건조를 위해 포화증기와 과열증기를 연속 적용하는 공정의 이용 가능성을 평가해보고자 하였다. 낙엽송 수심 정각재를 건조하는 동안 표면층, 내부층 및 중심층의 슬라이스 시험편을 통해 함수율 변화를 확인한 결과 포화증기 건조 중에는 표면층과 내부층 사이에서, 과열증기 건조 중에는 내부층과 중심층 사이에서 함수율 경사가 크게 발생하였다. 하지만 각 슬라이스 층간의 함수율 경사에도 불구하고, 표면 할렬은 발생하지 않았으며, 내부 할렬은 수나 미성숙재 부근에서만 발생하였다. 슬라이스의 탄성 변형률과 낙엽송의 접선 방향 탄성계수를 통해 건조 중인 낙엽송 정각재의 건조 응력의 최댓값은 1.30 MPa이었고, 건조 응력이 최대인 시점 온도와 함수율 조건에서 낙엽송의 접선 방향 인장강도는 5.21 MPa로 추산된다. 즉, 포화증기 및 과열증기를 연속 건조 공정에서 목재의 건조 응력이 접선 방향 인장강도를 초과하지 않았기 때문에 표면에서 할렬이 발생하지 않았다. 내부 할렬 발생 억제를 위한 과열증기 건조 조건 완화와 같은 추가 연구를 통해 포화-과열증기 연속 건조 공정이 대단면 목재 건조에 이용 가능할 것이라 기대된다.

• Journal of the Korean Wood Science and Technology
• /
• 제22권2호
• /
• pp.61-70
• /
• 1994

This study was executed to find the applicability of press drying of tree disk by investigating the shrinkage and drying defect and to form appropriate model by comparing the actual moisture content(MC) and internal temperature in respect of drying time with calculated values based computer simulation to which was applied finite difference method. In press drying disk, heating period, constant drying rate period maintained plateau temperature at 100$^{\circ}C$ and falling drying rate period were significantly distinguished. Actual MC and internal temperature were analogous to those calculated at comparing points. Heat transfer model formed by Fourier's law using specific heat of moist wood and conduction coefficient considering fractional volume of each element of wood cell wall, bound water, free water and air showed applicability as basic data to developing heat expansion, shrinkage and drying stress during press drying. Also mass transfer model formed by Fick's diffusion law using water vapor diffusion coefficient showed applicability. Longitudinal shrinkage was developed by pressure of hot press and tangential shrinkage was restrained by hygrothermal recovery. The heart check, surface check and ring failure were occurred differently in species, but V-shaped crack didn't develop.

• Journal of the Korean Wood Science and Technology
• /
• 제25권4호
• /
• pp.99-107
• /
• 1997

This study was executed to test the possibility of replacement for domestic Japanese larch(Larix leptolepis) for hardwoods and to acquire the information about the effects of drying temperature on internal temperature, moisture content and drying defects. In high-temperature drying, internal temperature increased rapidly to boiling point, immediately after that point the internal temperature rising rate was reduced. In the case of drying at temperature of $125^{\circ}C$, internal temperature could reach at boiling point in a very short time. Moisture content in high-temperature drying showed constant drying rate period and first period of falling rate drying together in 4 hours since experiment begun. There was no strong correlation between initial moisture content and final moisture content. Average drying rate at $115^{\circ}C$, $120^{\circ}C$ and $125^{\circ}C$ was 1.42%/hr, 1.88%/hr and 2.02%/hr, respectively; the case of drying temperature of $125^{\circ}C$ showed most rapid drying rate. Drying rate of $125^{\circ}C$ was so rapid that it showed more severe shrinkage, bow, collapse, end check, and internal check development than in other drying conditions. The result of this study showed the strong possibility of high-temperature drying for Japanese larch, and to dry Japanese larch optimally, dry bulb temperature should not exceed $120^{\circ}C$.

• Journal of the Korean Wood Science and Technology
• /
• 제29권3호
• /
• pp.21-26
• /
• 2001

Acquisition of precise information on drying characteristics of wood is indispensable for the improvement of drying schedules and wood quality. Recognition of the exact moisture content at which drying defects such as checks occur during drying with given drying conditions may be essential to reduce drying losses. In this study an image-processing system was combined with a laboratory-scale wood dry kiln for experiments and the surface of tree disk of black locust (Robinia pseudoacacia L.) was monitored to investigate the behavior of check formation over all the drying process. This system showed good potential for improving drying schedules and wood product quality.

• Journal of the Korean Wood Science and Technology
• /
• 제39권2호
• /
• pp.125-131
• /
• 2011

The characteristics of radio-frequency/vacuum drying Japanese larch boxed heart round logs with 150 mm and 210 mm in diameter and 2,500 mm in length, subjected to compressive loading, after the pretreatment of kerf were investigated. The results of this study were as the follows: The drying time of about 120 hours~130 hours was needed from green to about 15 percent of moisture content. The gradient of final moisture content for all specimens was very gentle in both longitudinal and transverse directions owing to dielectric heating. The surface checks seriously occurred although the occurrence extent of surface check for the kerfed specimens was slight compared with that for the control specimens because drying stress was relieved by kerf. The occurrence of surface checks for the L-specimen was more serious than that for the S-specimen.

• Journal of the Korean Wood Science and Technology
• /
• 제32권4호
• /
• pp.18-26
• /
• 2004

변장 14 cm 재장 2.4 m인 대단면재의 전도가열, 고주파가열 및 복합가열에 의한 진공건조특성을 조사하였다. 건조속도는 복합가열에서 가장 컸고, 고주파가열에서 가장 적었다. 비에너지는 고주파가열에서 가장 컸고, 전도가열에서 가장 적었다. 진공건조목재의 횡단방향 함수율분포는 전도가열과 복합가열의 경우 불록한 형태를 나타냈으나, 고주파가열의 경우는 한쪽 표층에서 반대쪽 표층으로 향해 증가하는 경향을 나타내었다. 건조목재의 재장방향 함수율은 전도가열과 복합가열의 경우 횡단면이 중심부위보다 낮았고 고주파가열의 경우 횡단면이 중심보다 높았다. 표면할렬과 횡단면할렬은 전도가열진공건조에서 가장 심하였다. 내부할렬은 어떠한 가열방법에 의한 건조에서도 발생하지 않았다. 복합가열 진공건조 특성은 전도가열과 고주파가열간의 절충된 중간적 경향을 나타냈다.