• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회B
• /
• pp.3423-3428
• /
• 2007

This paper shows that inlet humidity condition at cathode side is one of dominant parameters affecting the performance of PEMFC. To investigate effects of inlet humidity condition, the performance measurements were conducted for a single PEMFC with two operating variables : cathode relative humidity and dry condition in anode dry. The fuel cell employed for the experiments is a unit PEMFC with a 25$Cm^2$, Nafion$^(R)$112 membrane. As a result of this study, the cell performance is getting higher by increasing inlet humidity condition at cathode side. The cell performance is different from each operating temperature an it has maximum30% higher than dry condition at 60$^{\circ}C$ operating temperature with 80% relative humidity.

• 한국작물학회지
• /
• 제58권2호
• /
• pp.190-195
• /
• 2013

In this study, the response of 22 soybean cultivar sprouts to flooding stress was investigated. After sprouts were subjected to flooding stress for 10 days at the V4-V5 growth stages, their dry weights were compared. All plants were kept in a greenhouse under natural light conditions, an average daytime temperature of $35.6{\pm}5.3^{\circ}C$ and an average nighttime temperature of $18.2{\pm}1.7^{\circ}C$. Soybeans were grown in a concrete bed filled with silt loam soil. Subjecting plants to flooding stress resulted in a large reduction in plant dry weight, plant height, number of nodes, and number of leaves. Cultivars differed significantly in their responses to flooding stress, as indicated by these characteristics (p<0.05). Soybean cultivars were classified into three groups based on their degree of flood tolerance: strong, moderate, and weak. Hannamkong, Namhaekong, Sobaegnamulkong, and Sorogkong had strong tolerance for flood conditions. Tawonkong, Pureunkong, Eunhakong, Myeongjunamulkong, Doremikong, Saebyeolkong, Paldokong, Sowonkong, Pungsannamulkong, Dagikong, Dachaekong, and Anpyeongkong had weak tolerance for flood conditions.

• 한국식품과학회지
• /
• 제52권5호
• /
• pp.503-509
• /
• 2020

The present study investigated the effects of dry and moist heat treatments on total phenols, total anthocyanins, and antioxidant activity levels in black chokeberry (Aronia melanocarpa) fruits. Lyophilized chokeberry powder samples were heated in a drying oven at 60, 100, 160, 180, and 200℃ for 20, 40, or 60 min. Finely ground fresh chokeberry fruits were heated in water at 60, 80, and 100℃ for 20 min, and bioactive compound and antioxidant activity levels were measured. The bioactive compounds and antioxidant activity decreased with increasing temperature and treatment duration. Antioxidant activity was preserved at 160℃ or lower without significant loss for dry heating, whereas moist heat treatment increased both bioactive compounds and antioxidant activity with increasing temperature.

• 한국전기전자재료학회논문지
• /
• 제14권2호
• /
• pp.158-162
• /
• 2001

In this report, a new process for patterning of YBaCuO thin films, ICP(inductively coupled plasma) method, is described by comparing with existing wet etching method. Two 100㎛ wide and 2mm long YBaCuO striplines on LaAlO$_3$ substrates have been fabricated using two patterning techniques. And the properties were compared with the critical temperature and the SEM photography. Then, the critical temperatures of two samples were about 88 K, but the cross section of sample using ICP method was shaper than that using the wet etching method. ICP method can be used as a good etching technique process for patterning of YBaCuO superconductor.

• 한국마이크로전자및패키징학회:학술대회논문집
• /
• 한국마이크로전자및패키징학회 2003년도 기술심포지움 논문집
• /
• pp.169-173
• /
• 2003

We demonstrated the applicability of dry film photoresist (DFR) in photolithography process for fine pitch solder bumping on the polytetrafluoroethylene (PTFE/Teflon) printed circuit board (PCB). The copper lines were formed with $100\;{\mu}m$ width and $18\;{\mu}m$ thickness on the PTFE test board, and varying the gaps between two copper lines in a range of $100-200\;{\mu}m$. The DFRs of $15\;{\mu}m$ thickness were laminated by hot roll laminator, by varying laminating temperature from $100^{\circ}C\;to\;150^{\circ}C$ and laminating speed. We found the optimum process of DFR lamination on PTFE PCB and accomplished the formation of indium solder bumps. The optimum lamination condition was temperature of $150^{\circ}C$ and speed of about 0.63 cm/s. And the smallest size of indium solder bump was diameter of $50\;{\mu}m$ with pitch of $100\;{\mu}m$.

• 한국세라믹학회지
• /
• 제32권11호
• /
• pp.1283-1291
• /
• 1995

The electrical conductivity, flammable gas response and their humidity effect of porous ZnO, added with 5wt% corn starch as the fugitive phase, were examined. Porous ZnO showed different conductivity curves during increasing and decreasing temperature, and its electrical conductivity decreased rapidly by desorption of OH- between 20$0^{\circ}C$ and 35$0^{\circ}C$ when the temperature increased in dry air. The CO gas sensitivity of starchadded ZnO samples was higher than that of ZnO without starch addition. The sensitivity of porous, starchadded ZnO to 200ppm CO gas was much less in humid atmosphere than in dry atmosphere since water vapor increased the conductivity of porous ZnO in air, but decreased the conductivity in CO. Maximum sensitivity to 200 ppm CO gas balanced by air was about 100 in dry atmosphere and about 15 in RH 23% atmosphere.

• 한국기계가공학회지
• /
• 제8권3호
• /
• pp.74-81
• /
• 2009

At present, industries and researchers are looking for ways to reduce the use of lubricants because of ecological and economical reasons. Therefore, metal cutting is to move toward dry cutting or semi-dry cutting. One of the technologies is known as MQL machining. This paper presents an investigation into MQL machining with the objective of evaluating cylindricity and cooling effect for the turning process of SM45C. To reach this goal, cylindrical-outer-diameter turning experiments are carried out according to cutting conditions with fluid, MQL and dry machining methods. A cutting force, tool-shank temperature and cylindricity of workpiece are measured and analyzed. The correlation between cutting conditions and cylindricity are evaluated according to cooling lubricant environments.

• 한국의류학회지
• /
• 제23권5호
• /
• pp.757-763
• /
• 1999

The burn-out technique is used to result in the velvet cloth being patterned in open and solid areas by carbonize the cellulose fiber. It is examined how to burn out the cellulose part of the velvet without damage of the other part. The print paste indalca solution is mixed with sodium hydrogensulfate and lycerine and then screen-printed on the back side of the velvet. The effects of process conditions such as concentration of sodium hydrogensulfate dry heat fixation temperature and time pull no. and glycerine contents on the properties of ground farics were investigated. The yellowness index and the breaking load of silk ground fabrics afected by the process conditions especially concentration of sodium hydrogensulfate dry heat fixation temperature.

• 한국농공학회논문집
• /
• 제54권3호
• /
• pp.47-54
• /
• 2012

As a large construction such as highway, dam, reclaimed land etc. increase in number more and more, large amount of fill materials are required. It is needed to utilize a gypsum which is a by-product yielded from chemical plants, as fill materials. Though some studies have been conducted to know a engineering characteristic of gypsum, it is not certain that water contents were checked at $45^{\circ}C$ dry oven. This study proposed that water contents must be measured at $45^{\circ}C$ dry condition because gypsum is changed to other types as a dry temperature. As the results obtained by compaction tests, it is found that moisture of gypsum in compaction must be within -5.0~2.5 % O.M.C (optimal moisture content).

• 대한설비공학회지:설비저널
• /
• 제14권1호
• /
• pp.48-72
• /
• 1985