• Journal of the Korean Society of Safety
• /
• v.21 no.6 s.78
• /
• pp.7-13
• /
• 2006

A transient heat transfer and thermal stress analysis for a brake drum of commercial vehicles have been performed by ANSYS code in the cases of single braking and the repeated braking condition. The temperature and thermal stress distributions in the brake drum under various braking conditions were obtained using a two-dimensional axisymmetric model. In case of deceleration of 0.3G with an initial vehicle speed of 60km/h, the maximum temperature in the drum was $87.6^{\circ}C$ after braking application. The maximum stress of 78.7MPa in the drum occurred at the intersection between the flange and hat under a condition in which repeated 15 cycles braking with an initial vehicle speed of 60km/h and a deceleration of 0.3G is applied to according to KS R1129. The maximum stress value is much lower than the yield strength of drum material(FC250).

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2000.04a
• /
• pp.567-572
• /
• 2000

From the experimental study of W-EDM for alloyed steel, the characteristics such as Hand Drum Form and surface roughness have been observed and evaluated for various conditions. In square hole, the increase of IP as to made condition, the calculate high value of surface roughness. Also compare dimensionless square hole with circle hole' graph, In circle hole, if a value of surface roughness IP 6 in a side of circle it show a 0.4${\mu}{\textrm}{m}$ and in IP 8, 0.6${\mu}{\textrm}{m}$, in IP 10, 0.7${\mu}{\textrm}{m}$, in IP 12, 0.8${\mu}{\textrm}{m}$ higher than before. This figure show the surface roughness is higher than before, because a table move in either X-axis or Y-axis in square hole, on the contrary, in circle there table move in X-axis and Y-axis at the same time. hand drum form getting small when wire tension increase 1000gf to 1500gf, at the same working conditions. The smaller of off time, the maller of hand drum form in same condition and same wire tension. but if you compare square hole with circle hole' graph, hand drum form displayed in maintained term of working condision, on the contrary, in case of square hole variation of hand drum form is more increase than a grow of IP

• Journal of information and communication convergence engineering
• /
• v.6 no.1
• /
• pp.43-46
• /
• 2008

This paper proposes an advanced test circuit for detecting the connectivity between a drum ring of laser printer and PCB. The detection circuit of charge sharing is proposed, which minimizes the influences of internal parasitic capacitances. The test circuit is composed of precharge circuit, analog comparator, level shifter. Its functional operation is verified using $0.6{\mu}m$ 3.3V/40V CMOS process parameter by HSPICE. Access time is100ns. Layout of the drum contact test circuit is $465{\mu}m\;{\times}\;117{\mu}m$.

• Proceedings of the KSME Conference
• /
• 2000.11b
• /
• pp.645-650
• /
• 2000

This dynamic analysis is performed about shutdown, load controlled and temperature controlled startup operating characteristics of the Horizontal drum type HRSG. This analysis was performed by constructing a dynamic model of the plant and running it through the appropriate.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2001.04a
• /
• pp.707-710
• /
• 2001

Brakes are one of the important safety parts in cars. The requirements of brakes in performance, in comfort, and working lifetime are high. This paper presents the static analysis on the stress and temperature of a automotive drum brake. The particular interest is the distribution of the contact pressure between brake lining and drum. The problems to be solved are the effects of friction coefficient, actuation force, temperature, and brake component's stiffness. The contact problem includes friction, and is solved using the ABAQUS.

• Journal of the Korean Society of Safety
• /
• v.12 no.4
• /
• pp.9-14
• /
• 1997

From the experimental study of wire-cut Electric Discharge Machining for alloyed steel and tungsten carbide, the characteristics such as hand drum form has been observed and evaluated for various conditions. Hand drum form can be improved when gap voltage and spark cycle become smaller, their thickness become thinner, wire tension become larger and number of cutting is done so many times. When wire-cut 60mm thickness tungsten carbide in normal condition, Hand drum form becomes larger due to the low conductivity inducing cobalt composite rising by electrolysis.

• Journal of Families and Better Life
• /
• v.30 no.6
• /
• pp.85-101
• /
• 2012

This study was conducted to investigate the effect of group music therapy using the traditional drum on the; social adjustment, self-image, and emotional adjustment, of children with hearing impairment. I participated in this group music therapy using the traditional drum with 7 children with hearing impairment for 3 days a week for 6 weeks(including holidays), and each session was 50 minutes long. The evaluation form of this study is a social-emotional development measurement sheet of Meadow-Kendall, which the children's teacher distributed to the children both pre- and post-examination. With these results, the researcher carried out Window SPSS 19 Version and searched for the experiment's effect of measurement cause (I am not sure what this means.) through paired t-test to identify the experiment's effects (social adjustment, self-image, emotional adjustment) as a result of group music therapy using the traditional drum for children with hearing impairment. This study arrived at the following conclusions. First, after I participated in the group music therapy using the traditional drum, the result of the comparisons of the pre-to-post average for social adjustment showed the statistical significance level of the 0.01 standard. Therefore, it was found that the group music therapy using the traditional drum had a positive effect on the social adjustment of children with hearing Impairment. Second, after I participated in the group music therapy using the traditional drum, the result of the comparisons of the pre-to-post average for self-image development showed the statistical significance level of the 0.01 standard. Therefore, the group music therapy using the traditional drum had a positive effect on the self-image of children with hearing impairment. Third, after I participated in the group music therapy using the traditional drum, the result of the comparisons of the pre-to-post average for emotional adjustment showed the statistical significance level of the 0.01 standard. Therefore, the group music therapy using the traditional drum had a positive effect on the emotional adjustment of children with hearing impairment.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.19 no.7
• /
• pp.52-59
• /
• 2020

Automatic tool changers (ATCs) can be divided into drum and chain types. Drum-type ATCs contain a magazine, where the tools are mounted, and a cam gearbox, which swaps the tools via roller gear and grooved plate cams. Drum-type ATCs are advantageous in that the operating time for the tool magazine is more rapid than that of chain-type ATCs and the length of the unit is shorter. Thus, drum-type ATCs can be fabricated into various shapes and forms depending on the number of tools and the magazine size in accordance with machining center requirements and consumer demand. In particular, the price competitiveness of a machining center with a drum-type ATC is higher, while drum-type ATCs are more rigid with fewer parts, possibly reducing the need for regular servicing. This study aims to verify the structural stability and design validity of the magazine base, which is the main structure of a drum-type ATC, using finite element analysis. This study kinematically verifies the specifications of the selected drive motor and reducer and assessed the design of the cam gearbox. It also conducts a structural analysis of the roller camp, which is the core component of the cam gearbox, based on the results of the kinetodynamic analysis, thus validating the structural design.

• Journal of Korean Society for Geospatial Information Science
• /
• v.17 no.2
• /
• pp.71-79
• /
• 2009

In this study, a distributed rainfall-runoff model, K-DRUM, based on physical kinematic wave was developed to simulate temporal and spatial distribution of flood discharge considering grid rainfall and grid based GIS hydrological parameters. The developed model can simulate temporal and spatial distribution of surface flow and sub-surface flow during flood period, and input parameters of ASCII format as pre-process can be extracted using ArcView. Output results of ASCII format as post-process can be created to express distribution of discharge in the watershed using GIS and express discharge as animation using TecPlot. an auto calibration method for initial soil moisture conditions that have an effect on discharge in the physics based K-DRUM was additionally developed. The baseflow for Namgang Dam Watershed was analysed to review the applicability of the developed auto calibration method. The accuracy of discharge analysis for application of the method was evaluated using RMSE and NRMSE. Problems in running time and inaccuracy setting using the existing trial and error method were solved by applying an auto calibration method in setting initial soil moisture conditions of K-DRUM.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1996.05a
• /
• pp.36-40
• /
• 1996

A numerical analysis is performed about the static and dynamic characteristics of the oil-lubricated herringbone-grooved journal bearing which has circular groove profile. Some tests of jitter and W/F measurements are carried out to verify the performance of the newly designed drum assembly.