• Steel and Composite Structures
• /
• v.12 no.3
• /
• pp.207-230
• /
• 2012

Nowadays CFRP (Carbon Fiber Reinforced Polymer) became widely used materials for the strengthening and retrofitting of structures. Many experimental and analytical studies are encountered at literature about strengthening beams by using this kind of materials against static loads and cyclic loads such as earthquake or wind loading for investigating their behavior. But authors did not found any study about strengthening of RC beams by using CFRP against low velocity impact and investigating their behavior. For these reasons an experimental study is conducted on totally ten strengthened RC beams. Impact loading is applied on to specimens by using an impact loading system that is designed by authors. Investigated parameters were concrete compression strength and drop height. Two different sets of specimens with different concrete compression strength tested under the impact loading that are applied by dropping constant weight hammer from five different heights. The acceleration arises from the impact loading is measured against time. The change of velocity, displacement and energy are calculated for all specimens. The failure modes of the specimens with normal and high concrete compression strength are observed under the loading of constant weight impact hammer that are dropped from different heights. Impact behaviors of beams are positively affected from the strengthening with CFRP. Measured accelerations, the number of drops up to failure and dissipated energy are increased. Finite element analysis that are made by using ABAQUS software is used for the simulation of experiments, and model gave compatible results with experiments.

• Journal of Communications and Networks
• /
• v.15 no.2
• /
• pp.122-131
• /
• 2013

We address the problem of effective vehicular routing in hostile scenarios where malicious nodes intend to jeopardize the delivery of messages. Compromised vehicles can severely affect the performance of the network by a number of attacks, such as selectively dropping messages, manipulating them on the fly, and the likes. One of the best performing solutions that has been used in static wireless sensor networks to deal with these attacks is based on the concept of watchdog nodes (also known as guard nodes) that collaborate to continue the forwarding of data packets in case a malicious behavior in a neighbor node is detected. In this work, we consider the beacon-less routing algorithm for vehicular environments routing protocol, which has been previously shown to perform very well in vehicular networks, and analyze whether a similar solution would be feasible for vehicular environments. Our simulation results in an urban scenario show that watchdog nodes are able to avoid up to a 50% of packet drops across different network densities and for different number of attackers, without introducing a significant increase in terms of control overhead. However, the overall performance of the routing protocol is still far from optimal. Thus, in the case of vehicular networks, watchdog nodes alone are not able to completely alleviate these security threats.

• The Transactions of the Korean Institute of Electrical Engineers A
• /
• v.55 no.4
• /
• pp.139-143
• /
• 2006

Recently, standard of living improved and Information-Communication industry developed rapidly. Thereby, interest about electric power quality is rising worldwide. So, research and Development to enhance electric power quality in various viewpoint until most suitable supply system from each kind device to improve electric power quality. And specially, interest about voltage quality is rising by diffusion increase of information communication appliance and minuteness control appliance etc. Also Power consumption is increasing, but expansion of large size generator by environmental and site security problem is difficult. So, introduction of distribution generation is investigated actively by electric-power industry reorganization. Voltage management of power system had been controlled by ULTC (Under Load Tap Changer) in substation and pole transformer on the high voltage distribution line. But, voltage control device on substation and distribution line is applied each other separatively. Therefore, efficiency of line voltage control equipment is dropping. Also, research about introduction upper limit of distribution generation is consisting continuously. This paper presents cooperation use way between voltage control device and introduction upper limit of distribution generation for most suitable voltage control in distribution power system.

• Journal of Electrochemical Science and Technology
• /
• v.4 no.1
• /
• pp.1-18
• /
• 2013

Gallium is an important element in the production of a variety of compound semiconductors for optoelectronic devices. Gallium has a low melting point and is easily oxidized to give oxides of different compositions that depend on the conditions of solutions containing Ga. Gallium electrode reaction is highly irreversible in acidic media at the dropping mercury electrode. The passive film on a gallium surface is formed during anodic oxidation of gallium metal in alkaline media. Besides, some results in published reports have not been consistent and reproducible. An increase in the demand of intermetallic compounds and semiconductors containing gallium gives rise to studies on electrosynthesis of them and an increase of gallium concentration in the environment with various application of gallium causes the development of electroanalysis tools of Ga. It is required to understand the electrochemistry of Ga and to predict the electrochemical behavior of Ga to meet these needs. Any review papers related to the electrochemistry of gallium have not been published since 1978, when the review on the subject was published by Popova et al. In this study, the redox behavior, anodic oxidation, and electrodeposition of gallium, and trace determination of gallium by stripping voltammetries will be reviewed.

• Journal of the Korean Ceramic Society
• /
• v.37 no.4
• /
• pp.308-313
• /
• 2000

Hydrous titanium oxide particles with anatase phase were prepared from 0.05 mol TiCl4 solution using NH4HCO3 as precipitant by the droopping precipitant method. The sequential change of pH is completed by a sudden and steep increase in a pH value of the range of 6~7 to which the concentration of adsorbed OH- and H+ ions on TiO2 surface is equal. Rutile phase started precipitating with anatase phase as an increase of reaction temperature above 6$0^{\circ}C$ in aqueous 0.05mol TiCl4 solution and its specific surface area was found to decrease from 452 $m^2$/g($25^{\circ}C$) to 164$m^2$/g(8$0^{\circ}C$). Specific surface area decreased rapidly when anatase powders precipitated at 4$0^{\circ}C$ were heat-treated at temperature higher 40$0^{\circ}C$. FT-IR result confirmed that it was due to the decrease of OH species within hydrous titanium oxides. The loss of ethanol after illumination of the powder heated at $600^{\circ}C$ and $700^{\circ}C$ for 4 h was 66 and 68.8%, respectively.

• Journal of the Korean Ceramic Society
• /
• v.45 no.1
• /
• pp.43-47
• /
• 2008

The photocatalyst of $TiO_2$ coated on a fly ash composites (TCF) was prepared from precipitant dropping method to remove the acetaldehyde by photocatalytic reaction. The TCF were characterized by crystal aize, crystal structure and specific surface area. The photodegradation of acetaldehyde has been investigated using a UV-illuminated fixed photocatalytic reactor with TCF catalyst and P-25 catalyst in gas phase. The effect of photodegradation reaction conditions, such as initial concentration of acetaldehyde, concentration of oxidant in mixed gas and the light intensity on the photodegradation of acetaldehyde were investigated. P-25 catalyst showed the highest photodegradation of acetaldehyde and anatase $TiO_2$ coated TCF showed higher decomposition rate than rutile coated TCF. The photodegradation rate of acetaldehyde increased with the decrease of flow rate, initial concentration of acetaldehyde ($C_i$) and water vapor, however, it was increased with the increas of UV light intensity. The optimum conditions were weight of TCF=10 g, flow rate=50 ml/min $C_i$=100 ppm, concentration of oxygen=20%, concentration of water vapor=100 ppm.

• Journal of the Korean Ceramic Society
• /
• v.49 no.6
• /
• pp.518-522
• /
• 2012

Hyaluronic acid (HA) microbeads were synthesized by dropping 0.5 wt% of sodium hyaluronate dissolved in NaOH into 0.2 vol% of divinyl sulfone dissolved in 2-methyl-1propanol at a speed of 0.005 ml/min. HA microbeads were collected from a divinyl sulfone crosslinker solution stirred at 200 to 400 rpm for 5 h at temperatures from room temperature to $60^{\circ}C$ at intervals of $10^{\circ}C$. The crosslinked microbeads were then cleaned thoroughly using distilled water and ethanol. SEM results revealed that the microbeads were white-colored spheres. The 3-D porous network structure of the microbeads became dense with an increase in the crosslinking temperature; however, no dependence of the crosslinking temperature on the microbead size was detected. The extent of swelling decreased from 970% to 670% with an increase in the crosslinking temperature from room temperature to $60^{\circ}C$, most likely due to the increase in the degree of crosslinking.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.5 no.2
• /
• pp.169-184
• /
• 2002

In order to extract bearing information from the directional sensors of DIFAR(directional frequency analysis and recording) that is a kind of passive sonobuoy, the cardioid beamforming algorithm applicable to DIFAR system was studied in the frequency domain. the algorithm uses narrow-band signals propagated though the media from the acoustic sources such as ship machineries. The proposed algorithm is expected to give signal to noise ratio of 6dB when it uses the maximum response axis(MRA) among the Cardioid beams. The estimated bearings agree very well with those from GPS data. Assuming the bearings from GPS data to be real values, the estimation errors are analyzed statistically. The histogram of estimation errors in each frequency have Gaussian shape, the mean and standard deviation dropping in the ranges -1.1~$6.7^{\circ}$ and 13.3~$43.6^{\circ}$, respectively. Estimation errors are caused by SMR degradation due to propagation loss between the source and receiver, daily fluctuating geo-magnetic fields, and non-stationary background noises. If multiple DIFAR systems are employed, in addition to bearing, range information could be estimated and finally localization or tracking of a target is possible.

• Journal of Pharmacopuncture
• /
• v.15 no.1
• /
• pp.29-33
• /
• 2012

Objectives: Much evidence exists that herbs have effective immunomodulatory activities. Chrysanthemi Flos (CF) is effective in clearing heat, reducing inflammation, dropping blood pressure and treating headache and is used as a pharmaceutical raw material for an immune enhancer. The purpose of this study was to investigate the modulatory effect of Chrysanthemi Flos pharmacopuncture on nitric-oxide (NO) production in activating macrophages. Methods: After a murine macrophage cell line, RAW 264.7, was cultured in the presence of lipopolysaccharide (LPS), immune-modulating abilities of CF were evaluated by using NO, interleukin-6 (IL-6) and tumor necrosis factor-alpha (TNF-${\alpha}$) production and phagocytic activity of macrophages. Results: CF enhanced the activities of macrophages by increasing the phagocytic activity and decreasing NO production. Especially, both LPS and CF, 200 ${\mu}g/ml$, treatment could significantly reduce the NO production, but did not change the production of IL-6 and TNF-${\alpha}$. Conclusion: The results of this study indicate that CF may be of immunomodulatory value, especially for adverse diseases due to increased NO production. It may have potential for use as immunoenhancing pharmacopuncture.

• 한국방재학회:학술대회논문집
• /
• 2008.02a
• /
• pp.369-372
• /
• 2008

Recently, landslides have frequently occurred on natural slopes during periods of intense rainfall. With a rapidly increasing population on or near steep terrain in Korea, landslides have become one of the most significant natural hazards. Thus, it is necessary to protect people from landslides and to minimize the damage of houses, roads and other facilities. To accomplish this goal, many landslide prediction methods have been developed in the world. In this study, a simple landslide prediction system that enables people to escape the endangered area is introduced. The system is focused to debris flows which happen frequently during periods of intense rainfall. The system is based on the wireless sensor network (WSN) that is composed of sensor nodes, gateway, and server system. Sensor nodes comprising a sensing part and a communication part are developed to detect ground movement. Sensing part is designed to measure inclination angle and acceleration accurately, and communication part is deployed with Bluetooth (IEEE 802.15.1) module to transmit the data to the gateway. To verify the feasibility of this landslide prediction system, a series of experimental studies was performed at a small-scale earth slope equipped with an artificial rainfall dropping device. It is found that sensing nodes installed at slope can detect the ground motion when the slope starts to move. It is expected that the landslide prediction system by wireless senor network can provide early warnings when landslides such as debris flow occurs.