• Korean Chemical Engineering Research
• /
• v.53 no.5
• /
• pp.627-631
• /
• 2015

Various solid structures were prepared by electrospray technique. In this process, liquid flows out from a capillary nozzle under a high electrical potential and is subjected to an electric field, which causes elongation of the meniscus to form a jet. In our study, by controlling the amount of polyvinyl pyrrolydone in precursor solution, the jet either disrupted into droplets for the formation of spherical particles or was stretched in the electric field for the formation of fibers. During the electrospray process, the ethanol solvent was evaporated and induced the solidification of precursors, forming solid particles. The evaporation of ethanol solvent also enhanced the mass transport of solutes from the inner core to the solid shell, which facilitated fabrication of porous and hollow structure. The network structures were also prepared by heating the collector.

• Proceedings of the KSME Conference
• /
• 2008.11a
• /
• pp.1934-1938
• /
• 2008

Formation of air bubble is the one of common defects in UV nano imprint lithography. Location of dispensing and volume of droplets are among the most important parameters in the process. ]n this study, UV curable resin droplets with different volumes were dispensed at different locations and pressed to investigate air bubble formation. By varying volume of droplet and dispensing location, process conditions were found for minimum air bubble area.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1996.11a
• /
• pp.538-541
• /
• 1996

The flow of the molten drop in the GMAW was observed to explain the mechanism of its formation and break-up process. Fluid flew analysis was made with the assumption that the electrode wire acts like fluid, and it is shown how the convection of the drop inside affects its flow, from the formation to the break-up of the drop. In later part, the process of the spray mode development at high current is shown, as well as the one of the globular mode, by the fluid flow analysis.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.19 no.10
• /
• pp.2690-2698
• /
• 1995

Fuel atomization and mixture formation in an gasoline engine has influence on the engine performance and pollutant emission. The throttle valve installed in an intake system plays a greater role in control of mixture quantity in accordance with engine drive condition. In this study, the characteristics of secondary atomization developed at the downstream of the valves were observed using an image processing method. Two major kinds of valves, solid and perforated ones, are chosen in order to compare the valve performance with the experimental parameters of air flow rate, valve opening angle, and valve shapes. For the perforated valve, we can obtain the relatively small sized droplets, and nearly uniformed and dense distributed sprays with low loss coefficient than for the solid valve.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.24 no.7
• /
• pp.1010-1019
• /
• 2000

The main purpose of this article is to propose and assess a new spray impingement model considering film formation, which is capable of describing the droplet distribution and film flows in direct injection diesel engines. The spray-wall interaction model includes several mathematical formulae, newly made by the energy conservation law and some experimental results. The model consists of three representative regimes, rebound, deposition and splash. In addition, the film flow is described in the present model by solving the continuity and momentum equations for film flows using the integral method. To assess the new spray impingement model, the calculated results using the new model are compared with several experimental data for the normally impinging diesel sprays. The film model is also validated through comparing film radius and thickness against experimental data. The results show that the new model is generally in better agreement with experimental data and acceptable for prediction of the film radius and thickness.

• Journal of ILASS-Korea
• /
• v.17 no.1
• /
• pp.20-26
• /
• 2012

Inkjet printing is one of the direct writing technologies and is able to form a pattern onto substrate by dispensing droplets in desired position. Also, by inkjet technology manufacturing time and production costs can be reduced, and procedures can be more efficient. To form a metal pattern, it must be harmonized with conductive nano ink, printing process, sintering, and surface treatment. In this study, micro patterning of conductive line has been investigated using the piezoelectric printhead driven by a bipolar voltage signal is used to dispense $20-40{\mu}m$ diameter droplets and silver nano ink which consists of 50 nm silver particles. In addition, hydrophobic treatment of surface, overlap printing techniques, and sintering conditions with changing temperature and times to achieve higher conductivity.

• 연구논문집
• /
• s.31
• /
• pp.23-43
• /
• 2001

An experimental investigation on the reduction of nitrogen oxide emission from swirling, turbulent diffusion flames was conducted using multi air staged combustor, The combustor utilizes swirler to dampen fuel/air mixing, allowing an extended residence time for fuel pyrolysis and fuel-N conversion chemistry in an locally fuel-rich environment prior to burnout. This process also allow to reduce thermal NOx formation to lessen the temperature of reaction zone. The aerodynamic process therefore emulates the conventional staged combustion process, but without the need for the physically separate fuel-rich and -lean stages. Parametric studies on the ratios of each staged air and droplet size were carried out the feasibility of fuel/air mixing for low NOx combustion with diesel and pyridine mixed diesel fuel oil.

• Macromolecular Research
• /
• v.17 no.3
• /
• pp.163-167
• /
• 2009

This study presents a microfluidic method for the production of monodisperse poly(ethylene glycol) (PEG) microspheres using continuous droplet formation and in situ photopolymerization in microfluidic devices. We investigated the flow patterns for the stable formation of droplets using capillary number and the flow rate of the hexade-cane phase. Under the stable region, the resulting microspheres showed narrow size distribution having a coefficient of variation (CV) of below 1.8%. The size of microspheres ($45{\sim}95{\mu}m$) could be easily controlled by changing the interfacial tension between the two immiscible phases and the flow rates of the dispersed or continuous phase.

• Journal of the Korean Society of Visualization
• /
• v.21 no.2
• /
• pp.102-110
• /
• 2023

With the global shift from a carbon-based economy to a hydrogen-based economy, understanding the sloshing phenomenon and its impact on boil-off rate (BOR) in liquid hydrogen (LH2) tank trailers is crucial. Here, we analyze the primary breakup process under sloshing phenomena in a liquid fuel tank. We observe the growth of multiple holes on the sheet-like structures and the formation of ligament structures reminiscent of jet atomization. Through the extraction of three-dimensional liquid regions, we analyze the geometrical characteristics of these regions, enabling the classification of sheets, ligaments, and droplets. The present findings could contribute to understanding the breakup mechanism and hold potential for the development of strategies aimed at minimizing BOR.

• CELLMED
• /
• v.8 no.3
• /
• pp.11.1-11.6
• /
• 2018

In vitro anti-obesity effects of anti-cancer (AC) functional kimchi in differentiated 3T3-L1 adipocytes were studied. We constructed three experimental groups: Control, standardized kimchi (SK), and AC functional kimchi (A-FK) that included active ingredients and Lactobacillus plantarum. Kimchi extracts did not show any cytotoxicity in pre-adipocytes in the concentration range of 1 - 5 mg/mL. A-FK significantly reduced fat droplet formation and absorbance in differentiated 3T3-L1 adipocytes, as shown by Oil red O staining, compared to Control and SK (P < 0.05). SK and A-FK reduced adipo-/lipogenesis related genes such as $C/EBP{\alpha}$, SREBP-1, LPL, and $LXR{\alpha}$ compared to Control (P < 0.05). Especially, A-FK more greatly reduced SREBP-1 and LPL compared to SK (P < 0.05). A-FK up-regulated the ${\beta}$-oxidation related gene CPT-1c and down-regulated the pro-inflammatory cytokine IL-6 compared to Control (P < 0.05). Based on the results, A-FK exhibited anti-obesity effects by inhibiting fat droplet formation and adipo-/lipogenesis related genes by regulating the ${\beta}$-oxidation related gene CPT-1c and pro-inflammatory cytokine IL-6. In previous studies, A-FK kimchi already exhibited a strong anti-cancer effect. These results indicate that A-FK increased anti-obesity activity in this model system due to its functional ingredients and anti-cancer functionality.