• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.36 no.2
• /
• pp.80-87
• /
• 1987

This paper describes a new approach to control the two-phase servomotor driven with microprocessor based inverter. Conventional 6-step driving system has some shortcomings such as vibration and loss caused by the harmonic voltage. An attempt has been made to eliminate the harmonic content of output waveform by PWM technique and to simplify the control system by phase control method. In realizing the phase control by PWM technique proposed by this paper, control circuit and algorithm has been suggested. The proposed method has been applied to the speed control system with PI controller to confirm the adaptation of the servo system and experimental results has been compared with the computer simulation.

• Journal of Electrical Engineering and Technology
• /
• v.9 no.4
• /
• pp.1349-1354
• /
• 2014

This paper presents a compact and portable high-voltage generator based on magnetic-core Tesla transformer for driving an UWB high power electromagnetic source. In order to optimize the performance of the high-voltage generator, a novel open-loop cylindrical magnetic-core adopting the quad-division lamination structure is proposed and manufactured. The designed high-voltage generator using the proposed magnetic core has a battery-powered operation and compact size of $280mm{\times}150mm$ in length and diameter, respectively. The high-voltage generator can produce a voltage pulse waveform with peak amplitude of 450 kV, a rise time of 1.5 ns, and pulse duration of 2.5 ns at the 800 V input voltage.

• Proceedings of the KIEE Conference
• /
• summer
• /
• pp.1187-1189
• /
• 2004

This paper presents a boost circuit topology driving in high - frequency. It solves the problem which arised from hard-switching in high-frequency using a period of resonant circuit and operating under the principle of ZCS turn-on and ZCZVS turn-off commutation schemes. In the existing circuit, it has the high voltage stress in free-wheeling diode. But in the proposed circuit, it has voltage stress which is lower than voltage stress of existing circuit with modifing a location of free-wheeling diode. In this paper, it explained the circuit operation of each mode and the waveform of each mode. Also the experiment result compares the existing voltage stress of free-wheeling diode with the proposed voltage stress of that.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.48 no.9
• /
• pp.461-466
• /
• 1999

The switched reluctance motor (SRM) would have torque ripple if not operated with an MMF waveform specified for switching angle and phase voltage. This paper describes the robustic control scheme that permits the phase torque to be flat by PLL(Phase Locked Loop) controller. In this control scheme, the locked phase signal of PLL controls the switching dwell angle and it's loop filter signal controls the switching voltage adaptively. Experimental results show that stable dynamic performance is obtained for torque and speed together with low torque ripple on the operation of variable loads.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.11a
• /
• pp.273-277
• /
• 1999

A cold cathode flourescent lamp for the backlight in the notebook computer requires high input voltage about 1300(V) when it turns on. But once a discharge starts, the input voltage can be dropped by about one-third for continued output. The equivalent impedance also varies from open to several dozens of kilo-ohms. The piezoelectric transformer converts electrical energy into mechanical energy and then converts it back to electrical energy at a high voltage. Its high output voltage, high efficiency and small size are suitable for driving the LCD backlight in the notebook computer. The piezoelectric transformer operates near the resonance frequency and the output waveform is close to sine wave with very little noise. This paper suggests an inverter for LCD backlight of notebook computer using piezoelectric transformer that includes voltage to frequency converter for gate signal which is useful for tracking of variable resonance frequency depending on load impedance.

• Journal of the Semiconductor & Display Technology
• /
• v.17 no.3
• /
• pp.21-26
• /
• 2018

In this paper, the switching characteristics of the active clamp type flyback converter, which is deemed suitable for the miniaturization of the external power supply for home appliance, were analyzed and the process of reducing the switching loss was explained. The active clamp type flyback converter operating in the DCM has confirmed that the surge voltage of the main switch does not occur and the turn-off / on loss of the switch do not occur in principle. Also, in the case of the switch for synchronous rectifier, it was showed that the switch current showed half-wave rectified sinusoidal characteristic, and the switching loss was reduced. The switching characteristics of the experimental results gathered from 120 W class prototype were compared with the theoretical waveform in the steady-state and it was confirmed that the power conversion efficiency of the active clamp type flyback converter was maintained high due to the reduction of the switching loss.

• The Proceedings of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.7 no.3
• /
• pp.27-33
• /
• 1993

This paper presents the &tal controller for driving high frequency voltage fed PWM inverter that carrier frequency is over 2OkHz.We analyzed the conventional PWM to select a proper PWM pattern. as the result, obtained PWM pattern of the controller in which asynchronus staircase sinusoidal waveform is used as reference signal, and variable carrier ratio method was used for PWM control. The PWM controller is designed by fully digital method. Especially, Thk proposed controller is consisted of 8 bit one-chip microprocessor and digital logic. the former is for arithmetic and data processing, and the latter is for PWM pattern synthesis. Therefore, The responsibility and controllability is improved. Also, Data processing capability is improved using proper program to output modulation index with 9 bits. Circuits configuration of digital controller are made up of one chip 8051 and EPLD, and its controllability is tested by operating voltage fed inverter. Harmonics and current waveform is evaluated and analyzed for the voltage fed inverter system.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2008.10a
• /
• pp.1547-1550
• /
• 2008

We are suggesting a new index to represent the performance of PDP, such as Specific Performance Index (SPI) that includes luminous efficacy and panel reflectance. High Xe gas mixture and low panel capacitance are well known as key factors to improve luminous efficacy of PDP [1]. However, higher driving voltage and longer discharge time lag is an obstacle when applying these technologies. Modified cell design, new materials and driving waveform enable us to overcome these obstacles. High efficient phosphor is also a key material to improve luminous efficacy. Phosphors coated with pigment are used to reduce panel reflectance. High performance 50-inch HD PDP with luminous efficacy of 2.3 lm/W has been developed.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2003.07a
• /
• pp.722-725
• /
• 2003

In AC plasma display, it is very important to quantify the wall voltage induced by the wall charge accumulated on the dielectric surface. If we know the quantities of the wall voltage in each period of every sequence; reset period, address period and sustain period, then it helps us to design the optimal driving waveform for high efficiency plasma display. We develop a new method to measure the wall voltage with VDS (Versatile Driving Simulator) system. From this method the wall voltage induced by a wall charge profiles just after the reset discharge of every cells in plasma display panel can be investigated and analyzed successfully. It is noted that the wall voltage profiles are influenced by the space charge and then they are stabilized as time goes by. It is also noted that both the remaining wall charge at the previous sequence and space charges contribute to wall voltage quantities just after the reset discharge. It is noted that the wall charges contribute dominantly after a few hundreds microseconds, while the space charges have been decayed within 100 ${\mu}s$ just after the reset discharge.

• Journal of Sensor Science and Technology
• /
• v.8 no.6
• /
• pp.427-433
• /
• 1999

In this paper, we have presented an one-axis fluxgate magnetic sensor with ferrite core, excitation, and pick-up coil. This magnetometer is consist of a sensing element, driving circuits for excitation coil and signal processing for detecting second harmonic frequency component which is proportional to the DC magnetic to be measured. The sensor core is excited by a square waveform of voltage through 82 turns of the excitation coil. The second harmonic output of pick-up coil(150 turns) is measured by a FFT spectrum analyzer. This result is compared to output of PSD(phase sensitive detector) unit for detecting a second harmonic component. The measured sensitivity is about 50 V/T at driving frequency of 2 kHz. The nonlinearity of fluxgate magnetic sensor is calculated about 2.0%.