• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 추계학술대회논문집A
• /
• pp.654-659
• /
• 2001

In the virtual environment, reality can be enhanced by offering the motion based on a motion simulator in harmony with visual and auditory modalities. In this research, the Stewart platform based motion simulator has been developed. This motion simulator is driven by the electric motors, and offers the slightly wider workspace compared to the commercial available simulators. In order to compensate for the limited range of the motion platform, the washout filters with fixed coefficients have been usually adopted. In this paper the new approach is proposed to tune the filter coefficients based on the fuzzy logic on the real-time basis. It is shown that performance with the variable filter coefficients is better than that with the fixed ones. The driving simulator based on the bicycle dynamics was developed by integrating the motion simulator and graphic system.

• 한국농업기계학회:학술대회논문집
• /
• 한국농업기계학회 1996년도 International Conference on Agricultural Machinery Engineering Proceedings
• /
• pp.469-477
• /
• 1996

In order to maintain a constant ratio between the ground wheel and fed shaft of planters, a feedback control unit was designed to drive the feed shaft in proportional to the ground speed. The fifth wheel was used as a ground speed sensor for the control unit. Using this control unit a feed shaft driving system was developed and tested both in the laboratory and field to evaluate it performance . The test results showed that the system drove the feed shaft in proportional to the ground speed in the normal planting speed range of 0.5 -0.8m/s with an error of less than 5%.

• 동력기계공학회지
• /
• 제11권4호
• /
• pp.98-102
• /
• 2007

In this study, a measurement method of leakage flow-rate for pneumatic driving apparatus is proposed. The existing measurement methods of leakage flow-rate of air need disassemble the test component. Therefore, there is no effective method to measure the leakage flow-rate while operating pneumatic driving apparatus. In this study, the leakage flow-rate is measured from the pressure change in an isothermal chamber that can realize isothermal conditions by stuffing the steel wool into it. Therefore, a wide range of flow-rate could be measured only from the pressure response and the leakage flow-rate can be measured during operating pneumatic driving apparatus. The effectiveness of the proposed method is proved by experimental results.

• 유공압시스템학회논문집
• /
• 제3권1호
• /
• pp.15-19
• /
• 2006

In this study, a measurement method of leakage flow-rate for pneumatic driving apparatus is proposed. The existing measurement methods of leakage flow-rate of air need disassemble the test component. Therefore, there is no effective method to measure the leakage flow-rate while operating pneumatic driving apparatus. In this study, the leakage flow-rate is measure from the pressure change in an isothermal chamber that can realize isothermal conditions by stuffing steel wool into it. Therefore, wide range of flow-rate could be measured only from the pressure response and the leakage flow-rate can be measured during operating pneumatic driving apparatus. The effectiveness of the proposed method is proved by experimental results.

• Transactions on Electrical and Electronic Materials
• /
• 제7권3호
• /
• pp.103-107
• /
• 2006

In this paper, a CMOS complementary bridge rectifier for driving RFID transponder chips is presented. The proposed RFID CMOS complementary bridge rectifier is designed with two NMOSs at the input, which are configured by cross-connected gate structures, and two PMOSs and two NMOSs at the output, which are configured by diode-connected MOS structures. Output characteristics of the proposed rectifier are analyzed with the high frequency small-signal equivalent circuit and verified with SPICE for RFID operating frequencies of 13.56 MHz HF for ISO 18000-3, 915MHz UHF for ISO 18000-6, and 2.45 GHz microwave for ISO 18000-4. Simulation results show well-rectified and high enough DC output voltages for driving the low power microchip in the RFID transponder for the frequency range from HF to microwave. DC output voltages are dropped by only around 0.7 V from the input peak-to-peak voltages.

• 산업기술연구
• /
• 제31권A호
• /
• pp.95-101
• /
• 2011

According to recent technological developments in high-power LEDs, the stage lighting is one of most important areas to apply power LED system. Moving light for color rendering of stage uses the RGBW(red, green, blue, white) color mixing method. LED moving light system needs to have a wide range of dimming control as enough to operate at very low power. Also LED dimming system should not be induced color-shift and flicker in camera. This paper is experimentally verified the LED Moving Light driving circuit of 200Watt level designed to satisfy the above characteristics which applied the DC current-controlled and PWM mixed dimming method.

• 자동차안전학회지
• /
• 제13권1호
• /
• pp.26-30
• /
• 2021

K-city is an experimental area for developing self-driving cars. V2X communications such as WAVE, C-V2X and 5G are an essential technology for autonomous driving above level 4. In this paper, the research on the V2V communication environment was carried out through BSM receiving level analysis on the driving route in K-city. A stationary vehicle communicated with a test vehicle moving along urban area and suburban road in two different scenarios. The communication range and receiving levels obtained from this study will be used to develop and verify various safety scenarios using V2V communication within K-city in the future.

• 한국ITS학회 논문지
• /
• 제23권1호
• /
• pp.123-133
• /
• 2024

기존의 자율주행 기술은 차량에 부착된 센서를 사용하여 환경을 감지하고 주행 계획을 수립하는 방식으로 개발되었으나, 악천후나 역광, 장애물로 인한 가려짐 등 특정 상황에서 성능이 저하되는 문제점이 있다. 이러한 문제점을 해결하기 위해 도로 인프라의 지원을 통해 자율주행 차량의 인지 범위를 확장하는 협력형 자율주행 기술이 주목받고 있으나, 단안 카메라에서는 국제 표준에서 요구하는 객체의 3D 중심점을 실시간으로 분석해내기 어렵다는 문제점이 있다. 이에 본 논문에서는 도로 인프라의 고정된 화각과 사전에 측정된 기하학적 정보를 활용하여 객체를 검출하고 실시간으로 차량의 중심점을 추정하는 방법을 제안하였다. GPS 위치 측정 장비를 활용하여 객체의 중심점을 효과적으로 추정할 수 있음을 확인하였으며, 제안된 방법은 차량 및 도로 인프라 간의 협력형 자율주행 기술에 적용 가능하여, 협력형 자율주행 인프라의 보급 및 확산에 기여할 수 있을 것으로 기대된다.

• 전기전자학회논문지
• /
• 제25권1호
• /
• pp.148-155
• /
• 2021

로봇 기술이 발전함에 따라 모바일 로봇의 주행 시스템에 대한 연구가 활발히 진행되고 있다. 2륜 및 4륜의 휠을 기반으로 구성되는 모바일 로봇의 주행 시스템은 직선과 같은 단반향 주행에 장점이 있으나 방향 전환 및 제자리 회전에 단점을 가지고 있다. 볼을 휠로 사용하는 볼 로봇은 전방향 이동에 장점이 있으나, 구조적인 불안정한 특성에 의해 균형을 유지하기 위한 자세 제어 및 이동을 위한 주행 제어가 요구된다. 기존의 볼 로봇은 모터에 부착된 엔코더를 이용하여 주행제어를 위한 위치를 추정함으로써 오차가 누적되는 한계를 가지고 있다. 본 연구에서는 영상처리를 통해 볼 로봇의 위치 좌표를 추정하고, 이를 주행 제어에 사용하는 주행 제어 시스템을 제안하였다. 볼 로봇의 위치를 추정하기 위한 영상처리부, 통신부, 표시부 및 제어부를 포함하는 볼 로봇의 주행 제어 시스템을 설계 및 제작하고, 주행 제어 시스템을 적용한 볼 로봇의 주행 실험을 통해 x축 방향 ±50.3mm 및 y축 방향 ±53.9mm의 오차범위 이내에서 오차의 누적 없이 제어됨을 확인하였다.

• 한국생산제조학회지
• /
• 제8권2호
• /
• pp.126-136
• /
• 1999

We studied on crack growth retardation in single overloading condition. Crack tip branching which as the second mechanism on crack growth retardation was examined. Crack tip branching was observed to kinked type and forked type. It was found that the branching angle range was from 25 to 53 degree. The variations of crack driving force with branching angle were calculated with finite element method The variation of {{{{ KAPPA _I}}}}, {{{{ KAPPA _II}}}} and total crack driving force(K) were examined respectively So {{{{ KAPPA _I}}}}, {{{{ KAPPA _II}}}} and K mean to mode I, II and total crack driving force. Present model(Willenborg's model) for crack growth retardation prediction was modified to take into consideration the effects of crack tip branching When we predicted retardation with modified model. it was confirmed that predicted and experimental results coincided with well each other.