• 한국기계가공학회지
• /
• 제9권1호
• /
• pp.35-41
• /
• 2010

An overload limiter is used to prevent its overturning accident during an operation of a movable crane. Recently the indirect measuring method, which measures hoisting load and overturning moment of overload limiter, demands instead of the existing method, which measures only hoisting load. The indirectly measuring method is how to conduct the hoisting load and overturning moment as measuring the load of hydraulic cylinder for a luffing driving of boom. So we need to develop the multi-angular pin type load cell with the measuring angle of ${\pm}10$ degree instead of the existing load cell with the measuring angle of ${\pm}2$ degree. In this study the finite element analysis is conducted to evaluate the effect of the aspect ratio of measuring cross section on the measuring limit of the load cell to develop the many-angular pin type load cell. For this investigation, the aspect ratio of measuring cross section and load applying angle were adopted as design parameters and the stresses of measuring part were evaluated for each parameter.

• Tribology and Lubricants
• /
• 제27권2호
• /
• pp.65-70
• /
• 2011

The power servo cylinder for driving accurately turbine stop valve of an atomic power plant is necessary to do turn-over owing to a leakage of oil and a structure problem, especially, it of a power plant be in demand a high quality standard depends entirely on import. There are much problem that the AlBC be to used as a material of piston head in cylinder are caused by wear. Therefore, it is necessary to examine friction characteristics of it. In this study, wear test experiments was carried out with AlBC and SCM440, using reciprocating friction tester of pin on disk. This result was shown that the wear mechanism of AlBC on working condition is adhesive wear and the maximum temperature of infra redray thermal image of frictional surface show over 2 mm from contact surface of pin and disk.

• Journal of electromagnetic engineering and science
• /
• 제8권1호
• /
• pp.6-11
• /
• 2008

Advances in low power design open the possibility to harvest energy from the environment to power electronic circuits. Electrical energy can be harvested from piezoelectric transducer. Piezoelectric materials can be used as mechanisms to transfer mechanical energy usually vibrating system into electrical energy that can be stored and used to power other devices. Micro- to milli-watts power can be generated from vibrating system. We developed definitive and analytical models to predict the power generated from a cantilever beam attached with piezoelectric transducer. Analytical models are pin-force method, enhanced pin-force method and Euler-Bernoulli method. Harmonic oscillations and random noise will be the two different forcing functions used to drive each system. It has been selected the best model for generating electric power based upon the analytical results obtained.

• Nuclear Engineering and Technology
• /
• 제47권5호
• /
• pp.523-533
• /
• 2015

Three-dimensional flow phenomena in a wire-wrapped 37-pin fuel assembly mock-up of a Japanese loop-type sodium-cooled fast reactor, Monju, were investigated with a numerical analysis using a general-purpose commercial computational fluid dynamics code, CFX. Complicated and vortical flow phenomena in the wire-wrapped 37-pin fuel assembly were captured by a Reynolds-averaged Navier-Stokes flow simulation using a shear stress transport turbulence model. The main purpose of the current study is to understand the three-dimensional complex flow phenomena in a wire-wrapped fuel assembly to support the license issue for the core design. Computational fluid dynamics results show good agreement with friction factor correlation models. The secondary flow in the corner and edge subchannels is much stronger than that in an interior subchannel. The axial velocity averaged in the corner and edge subchannels is higher than that averaged in the interior subchannels. Three-dimensional multiscale vortex structures start to be formed by an interaction between secondary flows around each wire-wrapped pin. Behavior of the large-scale vortex structures in the corner and edge subchannels is closely related to the relative position between the hexagonal duct wall and the helically wrapped wire spacer. The small-scale vortex is axially developed in the interior subchannels. Furthermore, a driving force on each wire spacer surface is closely related to the relative position between the hexagonal duct wall and the wire spacer.

• 드라이브 ㆍ 컨트롤
• /
• 제16권4호
• /
• pp.9-15
• /
• 2019

Bucket trajectory is crucial regarding precision work with an excavator. In general, the bucket trajectory deviation is determined by the machining deviation of the frame, driving deviation of the driving hydraulic cylinder, clearance in the joints, and deformation of the structure. This paper investigated the relationship between the respective clearance in joints and the trajectory deviation of the bucket at the finishing work of the ditching for a 20-ton excavator. As a result, the larger the clearance, the larger deviation is increased at trajectory. However, it was found that the deviation of the rotation angle and displacement of the bucket was limited and the size of clearance does not affect closely on the contact angle of the pin shaft.

• 제어로봇시스템학회논문지
• /
• 제14권1호
• /
• pp.27-35
• /
• 2008

A navigation system is one of the important components of an unmanned ground vehicle (UGV). A GPS receiver collects data signals transmitted by (Earth orbiting) satellites. However, these data signals may contain many errors resulting misinformation and depending on one's position (environment), reception may be impossible. The proposed self-driven algorithm uses three low-cost GPS in order to minimize errors of existing inexpensive single GPS's driving algorithm. By using reliable final data, which is analyzed and combined from each of three GPS's received data signals, gathering a vehicle's steering performance information and its current pin-point position is improved even with error containing signals or from a place where signal gathering is impossible. The purpose of this thesis is to explain navigation system algorithm using multiple GPS and compass sensor and prove the algorithm through experiments.

• 한국자동차공학회논문집
• /
• 제22권2호
• /
• pp.1-6
• /
• 2014

In-wheel driving inverter inside engine room sometimes operates in the harsh environment like high temperature of about $105^{\circ}C$. Especially, the size and power density of the inverter has become smaller and more increased. Thus, it is essential to manage the temperature of the inverter with IGBT (Insulated Gate Bipolar Transistor) switching devices for performance and endurance, because the temperature can be getting increase. In this paper, we performed the thermal flow analysis of inverter models with wave type and pin fin type cooling channels, and investigated the heat transfer characteristics of the inverter models using cooling water on channels at 8 L/min and $65^{\circ}C$. Also, we compared the thermal performance under various conditions such as coolant flow rate and layered power module structure. Therefore, we determined the feasibility of the initial inverter models and the thermal performance enhancement.

• 한국생산제조학회지
• /
• 제23권6호
• /
• pp.624-629
• /
• 2014

The purpose of this study is to carry out the task of engine hesitation which occurred intermittently in driving due to the defective CKPS of LPI vehicles. As the result of the wrong data from the equipment of D-logger, the signal error of CKPS caused the engine hesitation. We performed a study in the followings to analyze and investigate the cause effectively. First, we have investigated the control wiring harness and connector pin contact defect inspection. Second, we have inspected the defection of CKPS separately. From this study, it was found that the engine hesitation were caused by the bad durability and we have showed how to diagnosis the fault of the engine hesitation intermittently while driving. Therefore, it is determined that we have to improve the durability of the CKPS through a strict quality control and to increase the reliability.

• 한국생산제조학회지
• /
• 제9권6호
• /
• pp.127-132
• /
• 2000

Morphological analysis of wear particles is one of useful methods for machine condition monitoring because it is well reflected in machine driving state. This paper was undertaken to apply to the condition monitoring of hydraulic piston motor. The lubricating wear test was performed under different experimental conditions using the wear test device and wear specimens of the pin on disk type was rubbed in paraffinic base oil by three kinds of lubricating materials, varying applied load, sliding distance. The four shape parameters(50% volumetric diameter, aspect, roundness and reflectivity) are used for morphological analysis of wear particles. The results showed that the four shape parameters of wear particles depend on a kind of the lubricating materials. It was capable of calculating presumed wear volume for three kinds of materials on driving time to foresee as damage condition of lubricating materials.

• Tribology and Lubricants
• /
• 제25권5호
• /
• pp.318-323
• /
• 2009

The oil characteristics and wear particles of Diesel engines with a DPF have been investigated as a function of a driving distance. The engine oil of SAE 5W30 with ACEA C3 is used for an oil film lubrication of the engine, which is equipped with Diesel particulate filter. Depending on the oil test results, the kinematic viscosity of used engine oils at 40 is degraded up to 5.1% compared with that of unused engine oils, SAE 5W30. And the kinematic viscosity of used engine oils at 100 is more degraded up to 8.1% compared with that of unused engine oils. The oil characteristic as a function of a mileage is not changed depending on the driving distance because of high quality of engine oils. But the aluminum and copper compounds, which are used as base materials of the engine bearing and a pin bush, are much worn and contaminated for the increased mileage of the car. The oil properties of used engine oils are relatively good except phosphorus and calcium additives, which are heavily engaged in the performance of the oils.