• Journal of Biosystems Engineering
• /
• 제37권6호
• /
• pp.352-358
• /
• 2012

Purpose: The inexpensive black box system was developed to acquire and save driving information, to give the slope information, and to transmit SOS and theft signal. Method: The device consists of a main micro controller to acquire and save data, a GPS sensor module, a CDMA module, a touch LCD module, a RF (Radio Frequency) ID module, a SD (Secure Digital) card module, an emergency electric power source, a theftproof circuit, and a sensing device. The sensing device consists of a 8 bit micro controller, a accelerometer to detect impulse, two slope sensors to detect roll and pitch angle and a circuit to detect operation of 6 lighting devices. Results: Test results are as follows: 1) a tractor can be start up only with an electronic key (password or RFID card), 2) theft signal was transmitted when a tractor moved without an electronic key, 3) SOS was transmitted at conditions that rollover or crash happened. 4) 5 more than per 1s data are recorded at 5 minute intervals as new file name in SD card. Conclusions: This system can be used to save travelling record, reduce accident, prevent theft and rescue life in the accidents.

• 마이크로전자및패키징학회지
• /
• 제7권3호
• /
• pp.31-36
• /
• 2000

RF(radio Frequency)용 MCM(Multichip Module)-D 기판 내장형 인덕터를 개발하였다. MCM 기술은 고밀도 패키징 기술로서 주로 디지털회로에 많이 적용되어 왔으나, 최근에는 아날로그회로 및 디지털회로가 혼재된 혼성신호 및 초고주파 회로에도 적용되고 있다. 혼성신호에서는 능동소자 주변에 많은 수의 수동소자가 연결되므로 MCM-D 기판에 수동소자를 내장시키면 원가절감과 시스템의 크기 축소 및 경량화를 이를 수 있을 뿐 아니라, 성능과 신뢰성을 향상시킬 수 있다. 본 논문에서 MCM-D 기판은 Cu/감광성 BCB(Benzocyclobutene)를 각각 금속배선 및 절연막 재료로 사용하였고, 금속배선은 Ti/Cu를 각각 1000 $\AA$/3000 $\AA$으로 스퍼터한 후 fountain 방식으로 전기 도금하여 3 $\mu\textrm{m}$ Cu를 형성하였으며, 인덕터는 coplanar구조로 하여 기존의 반도체 공정을 이용하여 MCM-D기판에 인덕터를 안정적으로 내장시키고 전기적 특성을 측정하였다.

• 한국정보통신학회논문지
• /
• 제14권5호
• /
• pp.1303-1310
• /
• 2010

최근 운전자의 건강상태 모니터링 및 졸음운전 방지를 위한 자동차용 부품관련 센서개발 및 시스템 연구들이 국내외에서 활발히 진행되고 있다. 본 논문은 이러한 운전자의 건강 상태 및 졸음운전을 점검하기 위해 체스트벨트 심전도 (ECG)와 손목착용형 산소포화도 (SpO2) 센서를 제작하여 생체신호를 측정하였으며, 측정된 심전도, 산소 포화도, 그리고 심장박동수 신호는 무선센서네트워크를 통해 수집, 전송 및 모니터링 등의 처리를 가능하게 하여 운전자에게 안전운행을 위한 정보를 제공하도록 하였다. 원격지인 서버 PC와 연결된 베이스스테이션으로 수집된 심전도와 용적맥파 신호에서 HRV (Heart Rate Variability, 심박변이도) 신호를 검출하였으며, 검출된 HRV 신호를 시간 영역과 주파수 영역에서의 해석을 통하여 운전자의 스트레스 지수 및 졸음 상태의 실시간 모니터링 및 졸음상태의 운전자에게 주의를 제공하기 위하여 알람을 제공하는 형태의 지능형 모니터링 시스템을 구현하였다.

• 전력전자학회논문지
• /
• 제10권4호
• /
• pp.313-322
• /
• 2005

본 논문은 복공진 인버터를 적용한 250[W] 메탈핼라이드램프를 구동하기 위한 고역률 전자식 안정기를 설계하고 구현하였다. 제안된 전자식 안정기는 역률 개선 회로기능을 갖는 부스트 능동 PFC 회로와 하프 브리지 복공진형 인버터로 구분된 2개의 전력처리단으로 구성되어 있다. 회로 기본동작원리 및 회로 해석은 무차원화 파라미터를 도입하여 범용성을 부여하여 도식적으로 나타내었다. 음향공명을 제거하기 위해 타이머 IC와 구동 IC로 구성된 간단한 주파수 제어기를 구현하였다. 실험을 통해 복공진 인버터를 적용한 고역률 메탈핼라이드램프용 전자식 안정기가 안정적으로 동작함을 확인하였다

• 전력전자학회논문지
• /
• 제8권6호
• /
• pp.504-511
• /
• 2003

본 연구에서는 네온 변압기를 세라믹 계열의 압전 변압기를 이용한 인버터식 네온관용 변압기를 제안하였다 인버터식 네온관용 압전 변압기의 주요 구성은 정류부, 발진부, 공진형 하프브릿지 인버터회로부 및 압전 변압기부로 구성 제작하였다. 네온관용 변압기는 지금까지 개발된 압전 변압기 용량 보다 대부분 큰 용량을 필요로 하고 있기 때문에 압전 변압기의 용량 증가를 위해 병렬 구동하였다 이때 병렬로 연결된 단층형 압전 변압기간 내부 임피던스 값의 불일치로 발생하는 불평형 전류를 최소화 하기 위하여 압전 변압기별로 LC 필터값을 분석 부착하여 전압의 왜곡율을 최소화 하여 안정된 정현파 출력을 구현하였다. 그리고 이를 컴퓨터 시뮬레이션 실험과 실제 네온관 부착 실험을 통하여 전력 밀도와 절연 레벨이 높고, 누설 자속이 없는 소형, 경량화된, 압전 변압기를 적용한 인버터식 네온관용 변압기가 기존의 자기식 네온관용 변압기 보다 우수함을 비교 입증하였다.

• 융합신호처리학회논문지
• /
• 제17권2호
• /
• pp.77-82
• /
• 2016

운전자에게 각성뇌파를 생성할 수 있는 SSVEP기반의 졸음퇴치 도로시설물 시제품 개발을 위하여 실험을 통한 표준 인터페이스 모델의 개발 및 실험 검증 자료를 구축하는데 있다. 먼저 프로그램 시뮬레이션으로 SSVEP 자극 프로그램을 만들어서 체커 보드의 자극패턴을 만들었고 SSVEP의 주파수를 베타파 영역(13~30Hz) 내에 설정하였다. 고속도로 졸음취약지점에서 설치하여 운전중에 SSVEP 광자극에 대한 효과검증에 관한 실험 결과 주간과 야간 모두 고속도로 운전 중 SSVEP 광자극을 받으면 순간 베타파가 증가하는 것을 확인하였고, 5분 유지기 동안 보다 높은 각성상태를 유지하는 것으로 확인되었다.

• Journal of Biosystems Engineering
• /
• 제9권2호
• /
• pp.48-57
• /
• 1984

To analyze the grain transport velocity, which is valuable for optimizing the separation losses, an oscillating appratus for sieve was designed. The grain transport velocity was measured in each combination of three amplitude levels, three rpm levels and four projection angle levels. To analyze the grain transport velocity theortically, two computer programs were developed. And the results from experiment and theoretical analysis were compared. 1. The grain transport velocity was increased with the projection angle of oscillating sieve. Especially when the projection angle is higher than $45^{\circ}$ the grain transport velocity on the flat-plate was not increased but on the racked surface was increased persistently. 2. The grain transport velocity was increased linearly with the frequency of oscillating motion. The speed of driving link must be higher than 350 rpm at 24mm amplitude, 250 rpm at 36 mm amplitude to transport the grain efficiently. 3. The grain transport velocity was increased with the amplitude of oscillating motion. But if the amplitude was smaller than interval of racks, the grain on the racked surface was not transported, even though the projection angle or the speed of revolutionary link was increased. 4. The transport characteristics of a grain varied with the amplitude and projection angle. Especially in the range of 1.5 < K < 2.3 at $45^{\circ}$ projection angle the transportation of grain was successful and the grain motion consisted of sliding movement (forward, backward) and jumping movement, which is considered recommendable for separating process of a combine sieve. 5. The results from theoretical analysis were approximately in accord with that from experiment.

• 한국자동차공학회논문집
• /
• 제13권4호
• /
• pp.152-159
• /
• 2005

The method of induction noise reduction can be classified by using passive control or active control method. However, the passive control method has a demerit to reduce the effect of noise reduction to low frequency (below) 500Hz) range and to be limited in a space of the engine room. Whereas, the active control method can overcome the demerit of passive control method. The algorithm of active control is mostly used in LMS (Least-Mean-Square) algorithm because it can obtain the complex transfer function easily in real-time. Especially, Filtered-X LMS (FXLMS) algorithm is applied to an ANC system. However, the convergence performance of LMS algorithm could not match if the FXLMS algorithm is applied to an active control of the induction noise under rapidly accelerated driving conditions. So, in order to solve the problem in this study, the Moving Bandpass Filter(MBPF) was proposed and implemented. The ANC using MBPF for the reduction of the induction noise shows that more noise reduction as 4dB than without MBPF.

• Transactions on Electrical and Electronic Materials
• /
• 제12권6호
• /
• pp.253-257
• /
• 2011

This study was carried out to solve problems such as radio frequency band depletion, confusion risk, and security loss in existing visible wireless communication systems, and to determine the applicability of next-generation networks. A light-emitting diode (LED) light communication system was implemented with a controlling switching light module using the ATmega16 micro-controller. To solve the existing modulation effect and disturbance in visible light communication, an integrated interface was evaluated with a driving light module and analyzes its reception property. A transmitter/receiver using the ATmel's micro-controller, high-intensity white LED-6 modules, and infrared sensor KSM60WLM and visible sensor TSL250RD were designed. An experiment from the initial value of distance to 2.5 m showed 0.46 V of the voltage loss, and if in long distance, external light interference occurred and light intensity was lost by external impact and thus data had to be modified or reset repeatedly. Additionally, when we used 6 modules through the remote controller's lighting dimming, data could be transmitted up to 1.76 m without any errors during the day and up to 2.29 m at night with around 2~3% communication error. If a special optical filter can reduce as much external light as possible in the integrated interface, the LED for lighting communication systems may be applied in next generation networks.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2005년도 추계학술대회논문집
• /
• pp.551-554
• /
• 2005

The method of the reduction of the automotive induction noise can be classified by the method of passive control and the method of active control. However, the passive control method has a demerit to reduce the effect of noise reduction at low frequency (below 500Hz) range and to be limited by a space of the engine room. Whereas, the active control method can overcome the demerit of passive control method. The algorithm of active control is mostly used the LMS (Least-Mean-Square) algorithm because the LMS algorithm can easily obtain the complex transfer function in real-time. Especially, When the Filtered-X LMS (FXLMS) algorithm is applied to an ANC system. However, the convergence performance of LMS algorithm goes bad when the FXLMS algorithm is applied to an active control of the induction noise under rapidly accelerated driving conditions. Thus Normalized FXLMS algorithm was developed to improve the control performance under the rapid acceleration. The advantage of Normalized FXLMS algorithm is that the step size is no longer constant. Instead, it varies with time. But there is one additional practical difficulty that can arise when a nonstationary input is used. If the input is zero for consecutive samples, then the step size becomes unbounded. So, in order to solve this problem. the Correlation FXLMS algorithm was developed. The Correlation FXLMS algorithm is realized by using an estimate of the cross correlation between the adaptation error and the filtered input signal to control the step size. In this paper, the performance of the Correlation FXLMS Is presented in comparison with that of the other FXLMS algorithms based on computer simulations.