• Journal of the Korean Wood Science and Technology
• /
• 제34권2호
• /
• pp.1-9
• /
• 2006

The structural wooden members of the ancient building are deteriorated by fungi and termite over time. The deteriorate of the members causes the decrease of the specific gravity and the strength of it, so the stability of the building is threatened. Therefore, in this study, the evaluation of the specific gravity, which is correlated with the strength of the wood, was conducted in the post member using Nondestructive Evaluation (NDE) - Drilling Resistance Test (DRT). For the purpose of it, the specific gravity and drilling resistance of small specimens was measured to obtain the correlation between the specific gravity and the drilling resistance. And then, the drilling resistance test of the post members, which were expected to have the deteriorated parts, was performed. Consequently, the correlation between the specific gravity and the drilling resistance was very high ($R^2=0.89$) and the distributions of the specific gravity were evaluated for the each member. Also, the results were verified by the visual inspection of the cross section of it. Especially, the various variations of the wood member such as the deteriorated parts with termite or fungi and the crack could be detected exactly but the knot couldn't because the drill could pass by or could not penetrate the knot.

• 한국지반공학회논문집
• /
• 제23권11호
• /
• pp.87-98
• /
• 2007

화재 후 터널 구조물의 신속한 복구를 위하여 화재손상 구간을 정확하고 빠르게 파악하는 것이 무엇보다도 중요하다고 할 수 있다. 본 연구에서는 화재로 인한 라이닝 콘크리트의 역학적 특성 변과를 라이닝의 두께방향으로 연속적으로 측정하기 위한 천공저항시험법을 제안하고, 천공시험으로부터 측정된 천공 변수들로부터 모르타르와 콘크리트의 역학적 특성을 추정하고자 하였다. 비교적 균질한 모르타르에 대하여 일련의 천공저항시험을 실시한 결과, 분당회전수가 1,300rpm, 관입속도가 1.40mm/sec, 그리고 비트직경이 10mm인 경우에 측정된 천공 반력값의 편차가 가장 작게 나타나 최적의 시험조건으로 판별할 수 있었다. 최적 시험조건에서 모르타르에 대해 천공저항시험을 실시한 결과, 천공반력과 모르타트의 압축강도 및 탄성계수 사이의 결정계수가 각각 0.91 및 0.93으로 나타나 양호한 상관관계를 도출할 수 있었다. 또한 콘크리트에 존재하는 골재의 영향을 고려하기 위하여 반력 에너지 개념을 제시하였고 실제 압축강도와의 결정계수는 0.94로서 역시 양호한 상관관계를 도출할 수 있었다. 이상과 같이 천공 비트의 관입과 동시에 연속적으로 재료의 역학적 특성을 추정할 수 있는 천공저항시험의 적용 가능성을 파악할 수 있었다.

• 한국공작기계학회논문집
• /
• 제10권5호
• /
• pp.39-44
• /
• 2001

In this paper, drill fred mechanism, cutting depth measuring device and sensing buzzer of drill contact were investigated in order to develop the micro-hole drilling machine. Also, measuring device of cutting resistance was developed in order to estimate cutting resistance from change of cutting condition. The results show that extremely-low fled rate(less then $17{\mu}m/S$${\mu}{\textrm}{m}$ /s) can be done and cutting depth can be measured by up to 1${\mu}{\textrm}{m}$ with developed drilling machine. Accordingly we could assemble a very cheap micro-hole drilling machine($\phi$ 0.05~0.5 mm). Also we got the some properties of cutting performance i.e. under the same condition, cutting torque decreases as increase of spindle speed and rapid fled of drill brings about the inferior cutting state under low spindle speed.

• Journal of the Korean Wood Science and Technology
• /
• 제31권6호
• /
• pp.45-54
• /
• 2003

The density and strength of wood is affected by degradations and defects, such as voids and knots. Old wooden structures such as traditional cultural properties have been deteriorated by these types of defects. They were evaluated by a visual observation that is difficult to evaluate the inner deterioration in structures. In this study, three nondestructive testing techniques were investigated to detect the wooden structural members. Ultrasonic stress wave tests, drilling resistance tests and visual inspections were used to examine the structural wood members. Patterns of Resistograph using by drilling resistance tests could indicate the features of internal wood such as voids, knots, decay, fungi, and so on. The technique just like as ultrasonic stress wave tests, however, difficult to detect exactly area where small amounts of internal deterioration in logs are. In spite of results of ultrasonic stress wave test, the internal deterioration of wooden structural members could be evaluated by the relationship between ultrasonic stress wave tests and drilling resistance tests.

• 한국정밀공학회지
• /
• 제2권3호
• /
• pp.28-40
• /
• 1985

In this study, to check up on the effect of the components of cutting resistance upon friction between drill and inside wall of hole in drilling, the experiment was performed with individual specimen of carbon steel, cast iron, aluminium alloy under various cutting conditions: depth of hole, cutting speed, feed rate, shape and material of specimen. On the basis of the experimental results, the following conclusions are drawn; 1. The components of cutting resis- tance were increased in proportion to the increase of depth of hole owing to frictional resistance of drill margin and chip-jamming. 2. As feed rates increase, torque and thrust were increased. When comparing to the increasing rate for these components respecitively, thrust is higher tendency than torque. 3. As drill diameter increase, torque and thrust were increased. When comparing to the increasing rate for these components respectively, torque is higher tendency than thrust. 4. In the case of torque, the frictional resistance between drill margin and inside wall of drilled hole accounts for about 20 percent of carbon steel, 14 of cast iron, 10 aluminium alloy in drilling. But the effect of thrust force could be negligible. 5. Comparison between the theoretical and experimental results showed a close agreement so far as depth of hole is about three times of drill diameter. But there was a wide difference between them beyond the rane of three times, because of characteristics of the drilling process.

• 대한기계학회논문집A
• /
• 제26권6호
• /
• pp.1120-1126
• /
• 2002

Machining characteristics of tool steels manufactured by electro slag casting process has been investigated in this study. For the estimation of machinability, turning and drilling tests are carried out. The chip shapes at various velocities are investigated for the comparison of turning workabilities of tool steels because the chip shapes reflect characteristics of cutting resistance. In case of drilling test, feed motor currents measured by a hall sensor are used as a measure for the drilling resistance. The machining characteristics of the tool steels are strongly correlated with tensile properties, such as tensile strength, hardness, and ductility. In case of turning workability, it was found to be favoured by the higher tensile strength, while the opposite is true far the drilling workability. The electro-slag casted materials show better turning workability in the viewpoint of chip shapes and, the quenching-tempered electro-slag casted material has relatively better drilling machinability than that of the annealed one.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2003년도 춘계학술대회 논문집
• /
• pp.1853-1856
• /
• 2003

Multi-layer printed circuit board(PCB) is being used widely for the product with relatively complex circuits such as TV, VTR and FAX. With the rapid enlargement of electronic and IT industry, the hole machining technology on multi-layer PCB is increasingly required to improve. Thus, the micro drilling with ultrasonic vibration can be a good method for hole machining. Unlike conventional drilling, ultrasonic vibration applied drilling introduces less wear and fracture of not only tool but also internal surface of workpiece due to little cutting resistance, thus, machinability can be improved. The experiment is conducted through the comparison between the results of conventional drilling and ultrasonic micro drilling as well as among each results by the variation according to not only feed rate of drill but also amplitude and frequency of ultrasonic vibration. The multi-layer PCB consists of 6 layers and ${\Phi}$0.3 diameter drill was used. As a result, it was found that the state of internal surfaces of holes on multiple layer PCBs is improved by the application of ultrasonic vibration.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2001년도 봄 학술발표회 논문집
• /
• pp.307-314
• /
• 2001

The bearing capacity of drilled shafts that take excavation by Percussion Rrotary Drilling(PRD) into consideration was evaluated using static and dynamic pile load tests. The emphasis was on quantifying the allowable bearing capacity and point load-transfer at the pile tip on seven instrumented steel piles. Of the seven instrumented piles, five piles are placed to the bottom of the excavation by rotary and pushing into the final depth of the excavation, as opposed to the two driven piles. Based on the results obtained, it is shown that the skin friction mobilized by PRD is much greater than point resistance, whereas in driven piles, the point resistance is greater than skin friction. It is also found that much greater pile capacity was proved in the case of drilled shafts, compared to the driven piles and thus, the excavation by rotary drilling gives reliable pile capacity required to design axially loaded piles.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2000년도 춘계학술대회 논문집
• /
• pp.882-885
• /
• 2000

The machinability of material was evaluated using high speed steel drill on hot-rolled high strength steel. Cutting resistance and tool wear were investigated by drilling experimentation. When the steel-board specimens were drilled in industrial condition, the relationship between average of thrust and cutting resistance was random because of slip of chuck and strain of workpiece. The primary objective of this study is to develop the strategy of analysis that can detect drilling states in industrial condition and such strategy is programmed with visual C++. The developed program can analyze thrust of initial rising zone. The result is obtained that thrust of rising zone is closely related to tool wear in despite of industrial condition.

• 한국기계기술학회지
• /
• 제13권2호
• /
• pp.1-7
• /
• 2011

The CFRP composite has a lot of merits such as mechanical characteristic, light and thermal resistance. For these merits, CFRP is applied to so many industrial area. In order to use the composite materials in the aircraft structures or machine elements, accurate surfaces for bearing mounting or joints must be provided, which require precise, machining. In this study, the specimens differentiating the stacking sequence of 5kinds were used. When drilling the carbon fiber reinforced plastics, it was checked on whether the stacking sequence reached any effect on the cutting force. Also relationship between the drill diameter is examined from the drilling experiment, which is the drilling of Fabric, Unidirectional specimen with ∅6mm, ∅10mm, ∅12mm cemented carbide drill. Considering cutting force and drilling diameter, the results are analyzed.