• 소성∙가공
• /
• 제13권8호
• /
• pp.696-703
• /
• 2004

The purpose of this study is to examine the bulk/sheet forming characteristics of bulk amorphous alloys in the super cooled liquid state. Recently it is reported that amorphous alloys exhibit stress overshoot/undershoot and non-Newtonian behaviors even in the super cooled liquid state. The stress-strain curves with the temperature-dependences as well as strain-rate dependence of Newtonian/non-Newtonian viscosities of amorphous alloys are obtained based on the previous experimental works. Then, those curves are directly used in the thermo-mechanical finite element analyses. Upsetting and deep drawing of amorphous alloys are simulated to examine the effects of process parameters such as friction coefficient, forming speed and temperature. It could be concluded that the superior formability of an amorphous alloy can be obtained by taking the proper forming conditions.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2004년도 추계학술대회 논문집
• /
• pp.704-709
• /
• 2004

The wear behavior and the mechanical property of Cu-$TiB_2$ composites were examined. Cu-$TiB_2$ composites were fabricated by hot extrusion and cold drawing with $TiB_2$ contents(1$\∼$5vol.$\%$) and the size of $TiB_2$ particles(10$\mu$m and 20$\mu$m). The pin-an-disk wear test was carried out under dry sliding wear conditions which loads varied with from 20N to 100N. At the time, counterpart wear material used SM45C. The experimental results showed that the friction coefficient and wear rate decreased with increasing the $TiB_2$ contents and decreasing the size of $TiB_2$ particle. Also, the depth of plastically deformed zone decreased with increasing the $TiB_2$ contents and decreasing the size of $TiB_2$ particle.

• 한국지능시스템학회논문지
• /
• 제21권1호
• /
• pp.1-5
• /
• 2011

우리는 동의지수법에 의한 이변량정규분포의 변수 간 독립성에 대한 퍼지 상관 검정법을 제안하였다. 이를 위하여 퍼지 데이터의 조건을 제시하고, 퍼지 상관계수와 가설을 기각하고 채택할 정도를 위한 동의지수법을 정의하였다. 또한 예증을 위하여 한 이변량정규분포로부터 퍼지 표본을 추출하여 퍼지 상관계수를 이용한 최강력 불편 퍼지 검정법을 보였다.

• 소성∙가공
• /
• 제6권2호
• /
• pp.152-160
• /
• 1997

Three-Dimensional finite element analysis is performed using PAM-STAMP for design evaluation of automotive back door inner panel die. Gravity process by blank own weigth, binder-wrap process, and drawing process in the forming operations are sequentially simulated with Virtual Manufacturing Method. The most valuable result in this research is that 3-D FEM analysis can be applied to the design evaluation of draw dies in the die try-out, though effects of mesh size and drawbead resistance force on the try-out, the experimental knowhows about the forming variables such as friction coefficient punch velocity, drawbead force, etc are necessary.

• 디지털융복합연구
• /
• 제14권2호
• /
• pp.519-527
• /
• 2016

이 연구는 BMI 분류기준과 9점-신체상평정척도 분류기준의 일치도를 조사하여 현장적용의 유용성을 확인하고, 여대생들이 체형에 대해 실제로 인식하고 정도를 파악하여 체형인식의 왜곡에 대한 올바른 정보와 비만의 기준에 대한 정보 제공에 목적이 있다. BMI 분류기준과 신체상평정척도 분류기준의 일치도, 그리고 여대생의 BMI에 따른 신체상 인식 정도를 알아보기 위하여 교차분석, Spearman의 등위차상관계수 및 카파통계량을 산출하였다. 분석결과 일반 여자대학생이 판정한 신체상 평정척도 분류기준과 BMI 분류기준은 통계적으로 ${\rho}=.719$(p<.001)로 높은 상관과 ${\kappa}=.506$(p<.001)로 보통 수준의 일치도를 나타냈다. 이러한 결과를 바탕으로 차후 신체상과 관련하여 인종의 특성에 따른 크기와 형태를 조정할 필요가 있으며 인구통계학적 특성이 다르거나 비만도가 높은 대상자를 선별하여 그들의 체형인식과 심리적인 측면에 관한 추가적인 연구가 필요하다.

• 한국분무공학회지
• /
• 제25권1호
• /
• pp.8-14
• /
• 2020

Recently, 1-D model-based engine development using virtual engine system is getting more attention than experimental-based engine development due to the advantages in time and cost. Injection rate profile is the one of the main parameters that determine the start and end of combustion. Therefore, it is essential to set up a sophisticated model to accurately predict the injection rate as starting point of virtual engine system. In this research, procedure of 1-D model setup based on AMESim is introduced to predict the dynamic behavior and injection rate of diesel injector. As a first step, detailed 3D cross-sectional drawing of the injector was achieved, which can be done with help of precision measurement system. Then an approximate AMESim model was provided based on the 3D drawing, which is composed of three part such as solenoid part, control chamber part and needle and nozzle orifice part. However, validation results in terms of total injection quantity showed some errors over the acceptable level. Therefore, experimental work including needle movement visualization, solenoid part analysis and flow characteristics of injector part was performed together to provide more accuracy of 1-D model. Finally, 1-D model with the accuracy of less than 10% of error compared with experimental result in terms of injection quantity and injection rate shape under normal temperature and single injection condition was established. Further work considering fuel temperature and multiple injection will be performed.

• 한국정밀공학회지
• /
• 제24권3호
• /
• pp.91-99
• /
• 2007

Fractures of galvannealed coating layer during actual press forming in automotive applications were observed by scanning electron microscopy in order to understand fracture mechanism. Fracture behaviors of galvannealed coating layer in extra deep drawing quality steels and high strength steels have been studied by performing the tests describing the representative plastic deformation in sheet metal forming such as uni-axial tensile test, compression test, bi-axial test and plane strain test. Growth and direction of cracks were deeply related to the plastic deformation modes and history. The material properties of galvannealed coating layer were investigated by nano-indentation test equipped with Berkovich diamond indentor for the specimens. Hardness and elastic modulus of the coating layer were higher than bared steels and that was the reason for crack of coating layer. Flat friction test and drawbead friction test were performed to observe the effect of the surface morphology on the frictional characteristics. The micro-plasto hydrodynamic lubrication were appeared and played an important role in reducing the coefficient of friction.

• 디지털산업정보학회논문지
• /
• 제16권2호
• /
• pp.69-81
• /
• 2020

The objective of this study is to seek ways to maximize learning effects from e-learning by drawing improvement directions through investigating and analyzing an awareness of e-learning among e-learning attendees. The study was conducted among the attendees who are taking the e-learning program operated by K University and collected data from the students taking second semester in 2018 with the use of structured questionnaires. For data processing, SPSS Statistics 22.0 and AMOS were used, along with such analytical methods as frequency anslysis, descriptive statistical analysis, ANOVA (Analysis of Variance), t-analysis and cross tabulation. For significant data, it conducted an analysis by carrying out the Scheffe's test. According to the findings from this study, they showed a significant difference only in gender and curriculum desired to be opened in the question about e-learning participation motives per background factor. As for the learners' motives to study, it was confirmed that they tend to become more biased on time utilization and convenience of learning methods. The analysis of which factor of the three - learning factors, system factors and instructor's factors - has greatest effects on learning satisfaction indicated that learning factors influenced learning satisfaction the most in accordance with values for non-standard coefficient beta, followed by instructor factors which had a direct effect.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2005년도 춘계학술대회 논문집
• /
• pp.86-91
• /
• 2005

The stack, the core unit of the MCFC system, is composed of the three main parts which are the electrodes, the matrix keeping the electrolyte and the separator. Among these, the separator made of low carbon steel is manufactured by some sheet metal forming processes. The flatness of flange of the mask plate of the separator is crucial not only to enhance the stack performance but also to reduce the production cost. This study has focused on the enhancement of flatness of the mask plate flange by controlling some process parameters like the punch and die comer radii, the blank holding force, the friction coefficient and so on. The springback phenomenon occurring in the flange drawing process has been studied first using the finite element method (FEM) in order to understand what causes the springback. The distribution pattern of local longitudinal stress in the flanged part has been revealed very important in predicting the final shape of the flange. This fact has been backed up by the experimental results carried out with the developed test dies.

• Communications for Statistical Applications and Methods
• /
• 제28권4호
• /
• pp.339-350
• /
• 2021

In medical research, the risk factors associated with human diseases need to be identified to predict the incidence rate and determine the treatment plan. Logistic regression analysis is primarily used in order to select risk factors. However, individuals who are unfamiliar with statistics outcomes have trouble using these methods. In this study, we develop a nomogram that graphically represents the numerical association between the disease and risk factors in order to identify the risk factors for delirium and to interpret and use the results more effectively. By using the logistic regression model, we identify risk factors related to delirium, construct a nomogram and predict incidence rates. Additionally, we verify the developed nomogram using a receiver operation characteristics (ROC) curve and calibration plot. Nursing home, stroke/epilepsy, metabolic abnormality, hemodynamic instability, and analgesics were selected as risk factors. The validation results of the nomogram, built with the factors of training set and the test set of the AUC showed a statistically significant determination of 0.893 and 0.717, respectively. As a result of drawing the calibration plot, the coefficient of determination was 0.820. By using the nomogram developed in this paper, health professionals can easily predict the incidence rate of delirium for individual patients. Based on this information, the nomogram could be used as a useful tool to establish an individual's treatment plan.