• Journal of the Korea Institute of Military Science and Technology
• /
• v.15 no.3
• /
• pp.241-249
• /
• 2012

Performance analysis of the interior ballistics has been conducted using the 1-D numerical code called IBcode according to the various conditions such as length of ignition-gas injector, amount of ignition-gas, mass of projectile, and drag force of projectile. In case of the length of ignition-gas injector, the 25~100 % of the full-injector length has been considered as well as the mass & mass flow of the ignition-gas. The mass of the projectile 5~70 kg and its drag force of 0~69 MPa have been also considered. Variables such as breech & base pressure, negative differential pressure and muzzle velocity for the performance analysis have been sorted, too. Firing conditions for the optimal performance have been investigated through these variables.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.6 no.3
• /
• pp.1-7
• /
• 2002

During the preliminary design phase of aircraft development, it is necessary to evaluate many potential engine/airframe combinations to determine the best solution to given set of mission requirements and it is very important to establish a methodology to calculate precisely engine installed performance. It was carried out to calculate turbofan engine installed performance of a supersonic aircraft for a given engine/aircraft configuration. Thus "Thrust minus drag accounting system" was introduced to identify and calculate the elements of installed thrust or installed propulsive force by using the database based on wind tunnel test data. This paper describes the calculated results of installed thrust of turbofan engine for a supersonic aircraft. aircraft.

• Journal of Wind Energy
• /
• v.14 no.1
• /
• pp.21-28
• /
• 2023

This paper investigates the resistance performance of drag anchors used for aqua farms installed in southwestern offshore wind farms in Korea. These anchors have been employed for a long time without any quantitative evaluation. Experimental campaigns were performed at the target site and the results were used to validate the numerical model by changing the penetration depths in the uniformly distributed seabed (i.e., flat). Based on the validated model with good agreement with the experiments (ARE 1.8 %), the resistance of the anchor with different pullout angles was thoroughly examined. It is worth noting that the Coupled Eulerian-Lagrangian (CEL) technique was applied to account for the large deformation of the anchor; Eulerian for the seabed and Lagrangian for the structure. The numerical results indicated that the pullout resistance is vulnerable to horizontal inclined force rather than vertical inclination, implying that the optimum performance is ideally expected to be 0-degree force applied.

• International Journal of Aeronautical and Space Sciences
• /
• v.17 no.4
• /
• pp.579-592
• /
• 2016

CNUSAIL-1, to be launched into low-earth orbit, is a cubesat-class satellite equipped with a $2m{\times}2m$ solar sail. One of CNUSAIL's missions is to deploy its solar sail system, thereby deorbiting the satellite, at the end of the satellite's life. This paper presents the design results of the attitude control system for CNUSAIL-1, which maintains the normal vector of the sail by a 3-axis active attitude stabilization approach. The normal vector can be aligned in two orientations: i) along the anti-nadir direction, which minimizes the aerodynamic drag during the nadir-pointing mode, or ii) along the satellite velocity vector, which maximizes the drag during the deorbiting mode. The attitude control system also includes a B-dot controller for detumbling and an eigen-axis maneuver algorithm. The actuators for the attitude control are magnetic torquers and reaction wheels. The feasibility and performance of the design are verified in high-fidelity nonlinear simulations.

• 한국전산유체공학회:학술대회논문집
• /
• 1999.05a
• /
• pp.177-185
• /
• 1999

The airfoil design optimization procedures based on the Navier-Stokes equations were developed, This procedure enables more realistic and practical transonic airfoil designs. The modified Hicks-Henne functions were used to generate the shape of airfoils. Five Hick-Henne functions were used to design upper surface of airfoil only. To enhance the ability of Hick-Henne function to generate various airfoil shape with limited number of functions, the positions of control points were adjusted through optimization procedure. The design procedure was applied to the single-point design for the drag minimization problem with lift and area constraints. The result shows the capability of the procedure to generate much realistic airfoils with very small drag-creep in the low transonic regime. This is mainly due to the viscosity effect of Navier-Stokes flow analysis. However, in the higher transonic range tile drag-creep appears. The multi-point design is shown to be an effective way to avoid the drag-creep and improve off-design performance which is very similar in the Euler design.

• Journal of Mechanical Science and Technology
• /
• v.15 no.11
• /
• pp.1580-1587
• /
• 2001

In Part I, we extended the capability of the Goore Scheme for application to multi-dimensional problems and improved convergence performance. In this paper, we apply the improved Goore Scheme to th e control of turbulence for drag reduction. Direct numerical simulations combined with the control scheme are carried out to simulate a controlled turbulent channel flow at low Reynolds number. The wall blowing and suction is applied through the Goore algorithm using the total drag as feedback. An optimum distribution of the wall blowing and suction in terms of the wall-shear stresses in the spanwise and streamwise directions is sought. The best case reduces drag by more than 20 %.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.13 no.3
• /
• pp.372-377
• /
• 2010

The objective of this study is to predict the drag of an axisymmetric underwater vehicle with bluff afterbody using CFD. FLUENT, commercial CFD code, is used to simulate high Reynolds number turbulent flows around the vehicle. The computed drag coefficients are compared to available experimental data at various Reynolds numbers. Four widely used two-equation turbulence models are investigated to evaluate their performance of predicting the anisotropic turbulence in a recirculating flow region, which is caused by flow separation arising from the base of the vehicle. The simulations with Realizable ${\kappa}-{\varepsilon}$ and ${\kappa}-{\omega}$ SST turbulence models predict the anisotropic turbulent flows comparatively well and the drag prediction results with those models show good agreements with the experimental data.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.21 no.2
• /
• pp.23-30
• /
• 2022

After drilling, reaming is required to process a workpiece for obtaining an excellent surface quality. In general, a cermet is defined as a "composite of a ceramic hard phase and metal-bonded phase." Cermets have excellent abrasion resistance, thermal resistance, and performance in finishing operations that require surface roughness and processing precision. However, although cermets have significant advantages, research on them is insufficient. In this study, workpiece SM45C was machined using drills and cermet reamers. The cermet reamer was processed for drag finishing for 0, 4, and 6 min. The experimental results showed the effects of drag finishing on surface roughness and dimensional accuracy.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.15 no.4
• /
• pp.10-16
• /
• 2007

A rubber seal for wheel bearing which has been mainly applied to car wheel supporting device is required to have both high sealing performance and drag torque. Because of severe operational conditions like infiltration of mud or splashed water, the importance of rubber seal which is aimed for leakage prevention of grease and effective blocking of foreign substances has been increasing continuously. The sealing performance of this seal depends on several factors such as materials of seal, friction conditions of contact regions and geometry of seals and so on. We have focused on the effects of geometric characteristics such as the angle of main lip, interference between lip edge and inner metallic ring. In this study, the optimization of geometric variables was performed using the finite element analysis. For the sake of finite element analysis, uniaxial tensile tests were conducted and several constants for Mooney-Rivlin's equation were obtained. According to the results of this study, mock-up bearing was made. To verify this study, drag torque and mud spray test were preformed.

• 한국전산유체공학회:학술대회논문집
• /
• 2009.04a
• /
• pp.57-65
• /
• 2009

An efficient and high-fidelity design approach for wing-body shape optimization is presented. Depending on the size of design space and the number of design of variable, aerodynamic shape optimization process is carried out via different optimization strategies at each design stage. In the first stage, global optimization techniques are applied to planform design with a few geometric design variables. In the second stage, local optimization techniques are used for wing surface design with a lot of design variables to maintain a sufficient design space with a high DOF (Degree of Freedom) geometric change. For global optimization, Kriging method in conjunction with Genetic Algorithm (GA) is used. Asearching algorithm of EI (Expected Improvement) points is introduced to enhance the quality of global optimization for the wing-planform design. For local optimization, a discrete adjoint method is adopted. By the successive combination of global and local optimization techniques, drag minimization is performed for a multi-body aircraft configuration while maintaining the baseline lift and the wing weight at the same time. Through the design process, performances of the test models are remarkably improved in comparison with the single stage design approach. The performance of the proposed design framework including wing planform design variables can be efficiently evaluated by the drag decomposition method, which can examine the improvement of various drag components, such as induced drag, wave drag, viscous drag and profile drag.