• 한국유체기계학회 논문집
• /
• 제5권3호
• /
• pp.40-45
• /
• 2002

Since the previous cut-and-try design algorithm requires much cost and time, the automated design technique with the CFD and optimum design algorithm has recently been concerned. In this work, the Navier-Stokes equation was solved to gain more detailed viscous flow information of cascade with rotor-stator interactions. The H-grid embedded by O-grid was generated to obtain more accurate solution by eliminating the branch cut of H-grid near airfoil surface. To handle the relative motion of the rotor to the stationary stator, the sliding multiblock method was applied and the cubic-spline interpolation was used on the block interface boundary. To validate present procedure, the time-averaged aerodynamic loads were compared with experimeatal data. A good agreement was obtained. The Modified Method of Feasible Direction (MMFD) was used to carry out the sensitivity analysis of the change of aerodynamic performance by the changes of the cascade geometry. The present optimization of the cascade gave a dramatic reduction of the drag while the lift maintains at the value within the user-specified tolerance.

• 대한기계학회논문집B
• /
• 제26권8호
• /
• pp.1138-1144
• /
• 2002

Recently GDI(Gasoline Direct Injection) engine is spot-lighted to achieve higher thermal efficiency under partial loads and better performance at full loads. To realize this system, it is essential to make both stratified combustion and homogeneous combustion. Spray pattern must be optimized according to injection timing because ambient pressure in combustion chamber is varied with crank angle. In this experimental study, two types of visualization system such as laser scattering method and schlieren method were developed to clarity the spray behavior during on intake stroke. As the ambient pressure increases, thepenetration length and spray angle show a tendancy to decrease due to rising resistance caused by the drag force of the ambient air. Distribution of injected fuel on intake stroke has a significant effect on homogeneous mixture in the cylinder. These results provide the information on macroscopic wall-wet growth in the cylinder and design factors for developing GDI injector.

• 대한기계학회논문집B
• /
• 제22권5호
• /
• pp.640-650
• /
• 1998

Pumping performances of a helical molecular drag dump(MDP) and of a radial MDPs are numerically analyzed by using the direct simulation Monte Carlo (DSMC) method. A helical- and radial-MDP have rotating pumping channels cut on a cylinder and on a disk, respectively. For a helical MDP, the present results agree quantitatively with the previously known numerical results. For radial MDPs, both of the Type 1 (having pumping channels cut on the stationary disk) and of the Type 2 (having pumping channels cut on the rotating disk) are analyzed to predict their performances for various parameters, i.e., the radius of curvature center of the channel wall, the depth of the channel, the clearance between housing and disk, and the rotating speed. The results show that the performance of the Type 2 is superior to that of the Type 1, and that for all types the pumping efficiency decreases as the clearance increases. Also, the radial type MDP has larger leakage losses in the direction of pumping channel than does the helical one.

• 한국자동차공학회논문집
• /
• 제9권5호
• /
• pp.89-95
• /
• 2001

Recently GDI(Gasoline Direct Injection) engine is spotlighted to achieve higher thermal efficiency under partial loads and better performance at full loads. To realize this system, it is essential to make both stratified combustion and homogeneous combustion. When compared to PFI(Port Fuel Injection) engine, GDI engine needs more complicated control and optimal design with injection system. In addition, spray pattern must be optimized according to injection timing because ambient pressure in combustion chamber is also varied. Thus spray structure should be analyzed in details to meet various conditions. In this experimental study, two types of visualization system were developed to simulate compression stroke and intake stroke, respectively. With an increase of the ambient pressure, the penetration length tends to decrease due to rising resistance caused by the drag force of the ambient air. Spray characteristics impinged on the piston has a significant effect on mixture stratification around the spark plug. These results provide the information on macroscopic spray structure and design factors far developing GDI injector.

• 한국항해항만학회지
• /
• 제41권2호
• /
• pp.33-38
• /
• 2017

A marine flapped rudder is designed to improve the effective lift generated by the rudder; this also improves the maneuverability of the ship. The flap is a high lift device installed at the trailing edge of the rudder to augment lift. In this paper, the characteristics of a thick flapped rudder are analyzed at a low Reynolds number with various ratios of flap chord length to total chord length and various aspect ratios, based on the computational fluid dynamics technique. The performance of the rudder with respect to lift, drag, and center of pressure are investigated, and the efficient ratio of flap chord length to total chord length and improved aspect ratio are determined. Ed: highlight - or 'superior'. As a case study, the flow on the flapped rudder of an NACA0021 section shape in free stream condition is simulated. The standard k-epsilon turbulence model is used to model the flow around the flapped rudder. The results indicate that the efficient ratio of the flap chord length to total chord length and aspect ratio are 0.3 and 1.4, respectively.

• 한국항공우주학회지
• /
• 제36권9호
• /
• pp.835-840
• /
• 2008

단면상에 주름이 있는 잠자리 날개의 공기역학적 성능을 검토하기 위해 정지상태에 있는 2차원 비정상 수치해석을 수행하였다. 해석 조건으로서 레이놀즈수는 150과 1400, 10,000이며 받음각은 0도에서 40도까지 변화시켰다. 해석 결과 임계각 이상의 받음각에서는 주름에 의한 양력의 증가량은 거의 일정하게 유지되며 또한 날개 윗면의 주름은 양력의 증가에 거의 영향이 없음을 알 수 있었다.

• 한국항공운항학회지
• /
• 제24권4호
• /
• pp.35-43
• /
• 2016

UAV has been promoted for practical use in the field of civilian and military. Recently, UAV is required high-specification performance such as long-term flight and precision observation. Among these UAVs, High Altitude Long Endurance UAV(HALE UAV) has been developed for the purpose to replace some of the functions of the satellite such as meteorological observation, communications and internet relay while flying a long period in the stratosphere. In order to fly a long period in harsh environment of the stratosphere, aircraft needs high Lift-Drag-Ratio and weight reduction of the structure. This paper performed the structural analysis for fuselage and empennage of HALE UAV. Critical loading conditions for structural analysis are acquired from flight load analysis and finally the results of structural sizing for weight reduction is presented.

• Journal of Biosystems Engineering
• /
• 제33권5호
• /
• pp.289-295
• /
• 2008

The task of chemical spraying has been seriously considered as an irritating and annoying job for Korean rice farmers. An agricultural unmanned helicopter was suggested to solve this problem so as the farmers to have more decent farming condition. The objectives of this study were to analyze the adoptability of an experimental rotor blade (SW05) using the CFD simulation and also to compare the simulation results with experimental results. The simulation results showed that the induced power of this rotor reached to $57{\sim}63%$ of total power and the profile power was about $37{\sim}43%$ of total power. Therefore it can be concluded that this rotor's performance characteristics were not so efficient for the size of unmanned helicopter due to the low induced power and high profile power relatively compared with ones of conventional rotors. The comparison with experimental results showed that the tested lifts were less than 70% of simulated ones at the grip pitch of $12^{\circ}$ and decreased to 40% at the $18^{\circ}$ grip pitch. Therefore, it can be concluded that the rotor was too oversized to be used for a 15.4 kW (21 PS) engine.

• International Journal of Aeronautical and Space Sciences
• /
• 제18권1호
• /
• pp.144-153
• /
• 2017

In recent years, unmanned aerial vehicles (UAVs) have been developed and studied for various applications, including drone deliveries, broadcasting, scouting, crop dusting, and firefighting. To enable the wide use of UAVs, their exact aeroacoustic characteristics must be assessed. In this study, a noise prediction method for a ducted fan UAV with complicated geometry was developed. In general, calculation efficiency is increased by simulating a ducted fan UAV without the struts that fix the fuselage to the ducts. However, numerical predictions of noise and aerodynamics differ according to whether struts are present. In terms of aerodynamic performance, the total thrust with and without struts is similar owing to the tendency of the thrust of a blade to offset the drag of the struts. However, in aeroacoustic simulations, the strut effect should be considered in order to predict the UAV's noise because noise from the blades can be changed by the strut effect. Modelling of the strut effect revealed that the dominant tonal noises were closely correlated with the blade passage frequency of the experimental results. Based on the successful detection of noise sources from a ducted fan UAV system, using the proposed noise contribution contour, methods for noise reduction can be suggested by comparing numerical results with measured noise profiles.

• Steel and Composite Structures
• /
• 제19권4호
• /
• pp.939-952
• /
• 2015

In this paper, brake pad performance of two organic matrix composites namely, Sample 1 (contains no brass filler) and Sample 2 (contains 1.5% brass filler), is studied based on tribological and squeal noise behavior. In the first stage, a pin-on-disc tribometer is used to evaluate the frictional behavior of the two pads. On the following stage, these pads are tested on squeal noise occurrence using a drag-type brake dynamometer. From the two type of tests, the results show that; (i) brass fillers play a dual role; firstly as reinforcing element of the brake pad providing primary contact sites, and secondly as solid lubricant by contributing to the formation of a layer of granular material providing velocity accommodation between the pad and the disc; (ii) brass fillers contribute to friction force stabilization and smooth sliding behavior; (iii) the presence of small weight quantity of brass filler strongly contributes to squeal occurrences; (iv) there is close correlation between pin-on-disc tribometer and brake dynamometer tests in terms of tribological aspect.