• 한국표면공학회지
• /
• 제43권2호
• /
• pp.97-104
• /
• 2010

In this paper, we conducted MATLAB simulation using the reflectance formula and the Planck's black body radiation principle, for the purpose of identifying the opimum material and thickness of anti-reflective coating from double layered structures. We found that the optimum condition was obtained when refractive index of upper layer is 1.44 and that of lower layer is 2.29. As materials close to these refractive indices, $MgF_2$ as the upper layer and $HfO_2$, ZnS, $TiO_2$ as the lower layer were suggested. The best result in an average reflectance of 2.759% was obtained from a double layered structure of $MgF_2$ 94 nm/ZnS 55 nm.

• 열처리공학회지
• /
• 제15권3호
• /
• pp.118-126
• /
• 2002

TiCN thin films were deposited on tool steels at $510^{\circ}C$ by PECVD from a $TiCl_4+N_2+CH_4+H_2+Ar$ gaseous mixture. The microstructures and preferred orientation were investigated. The micro-scratch tests were performed using a system equipped with an acoustic emission sensor. Critical loads were determined to evaluate the adhesion of TiCN to substrate. The influences of the microstructures of substrates, double layered coatings, and coatings after nitriding(duplex coating) were investigated. The experimental results showed that the microstructures of substrates and double layered coating did not affect the critical loads considerably. By the duplex coating, critical loads were not always increased. In some cases, duplex coatings decreased critical loads significantly despite of absence of black layer. In this study, we tried to relate the results of scratch test to the residual stress analysis. Nitriding before the coating reduces the tensile residual stress in the film, which gives rise to low critical load in scratch test.

• Journal of Forest and Environmental Science
• /
• 제18권1호
• /
• pp.97-105
• /
• 2001

The main objective of this study was to investigate effects of pigment mixed with different ratio on the double coated paper. Mineral pigments such as clay and ground calcium carbonate(GCC) as well as hollow sphere plastic pigment were used to evaluate the physical, optical properties and printabilities of double coated paper. The physical properties such as gloss and smoothness, and the printability(ink gloss) of double coated paper were measured to evaluate the effects of the bottom layer on improving the properties of top layer. The data indicated that the usage of hollow sphere plastic pigment for the bottom layer coating improved the surface properties of double coated paper, and that ink gloss was significantly influenced by the structure of bottom layer even when hollow sphere plastic pigment was used for the bottom layer coating.

• 한국태양에너지학회:학술대회논문집
• /
• 한국태양에너지학회 2012년도 춘계학술발표대회 논문집
• /
• pp.243-247
• /
• 2012

The paper focuses on an anti-reflection (AR) coating deposited by PECVD in silicon solar cell fabrication. AR coating is effective to reduce the reflection of the light on the silicon wafer surface and then increase substantially the solar cell conversion efficiency. In this work, we carried out experiments to optimize double AR coating layer with silicon nitride and silicon oxide for the silicon solar cells. The p-type mono crystalline silicon wafers with $156{\times}156mm^2$ area, 0.5-3 ${\Omega}{\cdot}cm$ resistivity, and $200{\mu}m$ thickness were used. All wafers were textured in KOH solution, doped with $POCl_3$ and removed PSG before ARC process. The optimized thickness of each ARC layer was calculated by theoretical equation. For the double layer of AR coating, silicon nitride layer was deposited first using $SiH_4$ and $NH_3$, and then silicon oxide using $SiH_4$ and $N_2O$. As a result, reflectance of $SiO_2/SiN_x$ layer was lower than single $SiN_x$ and then it resulted in increase of short-circuit current and conversion efficiency. It indicates that the double AR coating layer is necessary to obtain the high efficiency solar cell with PECVD already used in commercial line.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2007년도 7th International Meeting on Information Display 제7권1호
• /
• pp.741-744
• /
• 2007

The research applied the processes of spin-coating and thermal-evaporating in proper order to deposit the hole transport material N,N'-Bis(naphthalen-1-yl)- N,N'-bis(phenyl)-benzidine (NPB) on the ITO substrate to make flexible organic light emitting diodes (FOLED) with double hole transport layer.

• Restorative Dentistry and Endodontics
• /
• 제36권3호
• /
• pp.203-210
• /
• 2011

연구목적: 이 연구의 목적은 다양한 방식의 한 단계 자가 부식 접착제의 적용이 직접 복합 레진 수복의 미세 인장 강도에 미치는 영향을 평가하는 것이었다. 연구 재료 및 방법: 36개의 발거된 대구치를 사용하여, 3종류의 한 단계 자가 부식 접착제(Clearfil Tri-S Bond, Adper Prompt L-Pop, G-Bond)와 적용 방식에 따라 12개의 군으로 나누었다. 접착제를 다음의 방식으로 상아질에 적용하였다. 1) single coating, 2) double coating, 3) manual agitation, 4) ultrasonic agitation. 접착제 적용 후, 광중합 복합 레진으로 수복하였다. 24시간 동안 실온의 증류수에 보관한 후, 각 군당 15개의 시편을 준비하여 미세인장 결합 강도를 측정하였다. 결과: Manual agitation, ultrasonic agitation군은 single coating, double coating군에 비해 유의하게 높은 미세인장 결합 강도를 보였다. Double coating군은 single coating군에 비해 유의하게 높은 미세인장 결합 강도를 보였으며, manual agitation군과 ultrasonic agitation군 간에는 미세인장 결합 강도의 유의한 차이가 없었다. 접착제 종류에 따라 미세인장 결합 강도의 유의한 차이가 있었고, 그 중 Clearfil Tri-S Bond가 가장 높았다. 결론: 한 단계 자가 산부식 접착제의 적용 방법과 재료에 따라 미세인장 결합 강도에 유의한 차이가 있었다. 접착제 종류에 관계없이 manual agitation과 ultrasonic agitation은 유의하게 높은 미세인장 결합강도를 보였다.

• 한국표면공학회지
• /
• 제50권5호
• /
• pp.345-351
• /
• 2017

A double-layered anti-reflective coating with hydrophilic/abrasion-resistant properties was studied using anatase titanium dioxide($TiO_2$) and silicon oxycarbide($SiO_xC_y$) thin film. $TiO_2$ and $SiO_xC_y$ thin films were sequentially deposited on a glass substrate by DC sputtering and PECVD, respectively. The optical properties were measured by UV-Vis-NIR spectrophotometer. The abrasion-resistance and the hydrophilicity were observed by a taber abrasion tester and a contact angle analyzer, respectively. The $TiO_2/SiO_xC_y$ double-layer thin film had an average transmittance of 91.3%, which was improved by 10% in the visible light region (400 to 800 nm) than that of the $TiO_2$ single-layer thin film. The contact angle of $TiO_2/SiO_xC_y$ film was $6.9^{\circ}$ right after UV exposure. After 9 days from the exposure, the contact angle was $10.2^{\circ}$, which was $33^{\circ}$ lower than that of the $TiO_2$ single-layer film. By the abrasion test, $SiO_xC_y$ film showed a superior abrasion-resistance to the $TiO_2$ film. Consequently, the $TiO_2/SiO_xC_y$ double-layer film has achieved superior anti-reflection, hydrophilicity, and abrasion resistance over the $TiO_2$ or $SiO_xC_y$ single-layer film.

• 한국식품영양과학회지
• /
• 제12권2호
• /
• pp.93-98
• /
• 1983

사과를 당저림과 넥타 겔로 가공한 후 피막제를 처리하여 저장 조건에 따른 중량 감소율을 측정하고 갈변 현상, 곰팡이의 발생을 실험하여 얻어진 결과는 다음과 같다. 1. 인체에 무해하고 중량 감소, 갈변, 곰팡이 발생을 억제하는 피막제의 구성은 sucrose, D-sorbitol, corn syrup, gelatin, arabia gum, citric acid, sodium citrate, sodium ascorbate가 효과적이었다. 2. 사과 당저림은 피막제 처리한 것을 포장하여 냉장고에서 저장하는 방법이 가장 효과적이었다. 3. 사과 넥타 겔은 피막제 처리한 것을 이중(二重) 포장하여 냉동하는 것이 중량 감소에 의한 수축, 갈변 현상, 곰팡이의 발생을 억제하였다.

• 한국인쇄학회지
• /
• 제18권1호
• /
• pp.1-11
• /
• 2000

The influence of the first coating layer on the properties of the second coating layer is reported. For various model coating composition, ratios of first and second coating weights are used to generate coating layers. The void volume, pore size distribution and light scatter coefficient of the coatings are measured. In some cases, the fine material from the second layer seems to penetrate the first layer to reduce the void fraction of the total system. Rapid setting coating, for example thin layers on porous first layer tends to generate porous coating layers.

• 한국태양에너지학회 논문집
• /
• 제31권6호
• /
• pp.95-102
• /
• 2011

The purpose of study is to estimate heating, cooling load performance and economic efficiency in office building with applied the functional paint. this paint can reduced SHGC(Solar Heat Gain Coefficient) on the glazing surface by coating. In this study, estimated to compared with double glazing, low-e glazing, IP(Insulation Paint) and IPu(Insulation UV-Cut Paint) coating glazing. As a result of this study, 1)heating & cooling load Analysis, SHGC value and U-factor of double glazing is about 0.70 and 3.29($W/m^2K$). low-E glazing is about 0.65 and 2.70($W/m^2K$). Two-side it is about 0.27 and 3.25($W/m^2K$). When compared to double glazing, annual heating & cooling load of low-E glazing, Two-side IPu and IP paint coating glazing is 3,012MWh($124kWh/m^2$), 2,910MWh($120kWh/m^2$), 2,867MWh($118.4kWh/m^2$) and 2,867MWh($118.4kWh/m^2$). It i sreduced to 2.0%, 5.2%, 6.7%, and 6.7% respectively. 2)the estimation of economic efficiency, low-e glazing installed in office building can not recover the investment within a lifetime 40years. but IPu and IP paint, two-side coating in glazing, have a payback period of 13 years respectively.