• 한국신재생에너지학회:학술대회논문집
• /
• 2010.11a
• /
• pp.103.1-103.1
• /
• 2010

Recently domestic wood pellet boilers are installed in rural and forestry houses. The fuel price per lower heating value of wood pellet is about 20 % lower than that of heating oil on July 2010. In spite of lower price of wood pellet, a few user of wood pellet boiler complain expensive fuel cost. One of this reason is inaccurate or improper air-fuel ratio setting of wood pellet boiler. O2 concentration of flue gas of domestic wood pellet boiler is about 9.7 % and there are few domestic wood pellet boiler which can control air-fuel ratio automatically. We tested a domestic wood pellet boiler in changing boiler thermal output and air-fuel ratio. The nominal boiler thermal output is 25 kW (21 500 kcal/h). We measured thermal efficiency and flue gas concentrations such as CO and NOx at each boiler thermal load with various air-fuel ratio. The results show that if air flow rate is the same as full load and part load, thermal efficiency of part load of 40 % drops about 7.7 %p compared to boiler full load case.

• Journal of the Korean Wood Science and Technology
• /
• v.46 no.2
• /
• pp.202-210
• /
• 2018

This study was carried out to quantify degree of contribution of harvested wood product (HWP) on mitigation of climate change by valuation of public benefits, environmentally and economically. The potential carbon dioxide emission reduction of HWP was estimated by accounting carbon storage effect and substitution effect. Based on 2014 statistics of Korea Forest Service, domestic HWPs were sorted by two categories, such as wood products produced domestically from domestic and imported roundwood. The wood products were divided into seven items; sawnwood, plywood, particle board, fiberboard (MDF), paper (including pulp), biomass (wood pellet) and other products. The carbon stock of wood products and substitution effects during manufacturing process was evaluated by items. Based on the relevant carbon emission factor and life cycle analysis, the amount of carbon dioxide emission per unit volume on HWP was quantified. The amounts of carbon stock of HWP produced from domestic and from imported roundwood were 3.8 million $tCO_{2eq}$., and 2.6 million $tCO_{2eq}$., respectively. Also, each reduction of carbon emission by substitution effect of HWP produced from domestic and imported roundwood was 3.1 million $tCO_{2eq}$. and 2.1 million $tCO_{2eq}$., respectively. The results of this study, the amount of carbon emission reduction of HWP, can be effectively used as a basic data for promotion of wood utilization to revise and establish new wood utilization promotion policy such as 'forest carbon offset scheme', and 'carbon storage labeling system of HWP'.

• Journal of the Korea Furniture Society
• /
• v.21 no.3
• /
• pp.229-236
• /
• 2010

Wood material is positive with the concept of eco-friendly materials. Wood toy preference of foreign brands is also a real problem. Therefore, in this domestic situation on Toys Brand Development, there are many problems yet to be solved. At First, a wood material for toys requires the development of more sophisticated and precision materials. Second, new content, product development and training program development of the toys are needed. Characters and content development time and effort should be invested. In present, Korean brand development of wood toy with educational effects is very important issues as the use of wood to match the low carbon & green growth.

• Journal of the Korean Wood Science and Technology
• /
• v.48 no.4
• /
• pp.450-457
• /
• 2020

Single pellet press technology allows for fast, low-cost, and small-scale tests to investigate pelletizing characteristics. We estimated proper compression ratios for five Korean domestic wood species through predicted relationships between pelletizing pressure P_x and compression ratio based on experimental data obtained from a single pellet press unit. The pressures required to obtain a 6-mm-diam pellet of density 1200 kg/㎥ were estimated as 111 MPa for Populus davidiana, 133 MPa for Robinia pseudoacacia, 136 MPa for Quercus mongolica, 97 MPa for Pinus densiflora, and 127 MPa for Pinus rigida. On the basis of these pressures, we estimated proper compression ratios to be within the range 7.676-8.410 for these species, and we found the compression ratios needed for hardwood species to be somewhat higher than those needed for softwood species to obtain the pellet density of 1200 kg/㎥.

• Journal of the Korean Wood Science and Technology
• /
• v.21 no.2
• /
• pp.67-72
• /
• 1993

Hot water extractives of sawdust/particle from domestic and foreign wood species, which were composed of pitch pine, Korean pine, larch, Italy poplar, acacia and oak as Korean wood species, Malaysian oil palm and German spruce were quantitatively analyzed with thin layer chromatography. Sugar components of saccharose, galactose, glucose, fructose and arabinose were contained in these wood species. It was assumed that arabinose and glucose are major inhibitory components against cement hardening in larch and oil palm, respectively, since both species contain a large amount of each sugar. In contrast, fructose might not influence so badly on a cement hardening, when considering that fructose was contained much in Italy poplar with a good cement hardening character. Galactose was a minor component.

• Journal of the Korean Wood Science and Technology
• /
• v.30 no.3
• /
• pp.104-108
• /
• 2002

Nail withdrawal tests were conducted on clear wood of domestic small diameter logs. Nails were driven into the cross and longitudinal sections of each specimen, then nail withdrawal tests were performed. Nail withdrawal loads are strongly dependent on the direction of nail positions. The average load values for the nail withdrawal both in cross section and longitudinal section are higher in high specific gravity (SG) wood of sawtooth oak (Quercus acutissima Carr.) than those in low SG wood of Korean red pine (Pinus densiflora Sieb. et Zucc.) and pitch pine (Pinus rigida Mill.). The average ratio of the nail withdrawal loads for side-grain and end-grain are higher in the low SG wood than that in the high SG of wood. Both linear and non-linear regression analyses were conducted on nail withdrawal load with SG, good correlations were obtained between nail withdrawal load and SG.

• Journal of the Korean Wood Science and Technology
• /
• v.39 no.3
• /
• pp.252-257
• /
• 2011

Tests were carried out on domestic wood samples to modify the formula which had previously been developed to predict the withdrawal strength of screw on the face of lumber. Screw sizes were No. 6, 8 and 10 used in this study. Predicted equations were fitted to the results of different length of No. 8 wood screw. The withdrawal strength of screws was enabled to predicted as a function of screw diameter, depth of penetration, and specific gravity of wood. Predicted equation was under-predicted the withdrawal strength of 25 and 30 mm length of screw within 5% and over-predicted withdrawal strength of 18 and 38 mm length of screw.

• Journal of the Korean Wood Science and Technology
• /
• v.38 no.5
• /
• pp.391-398
• /
• 2010

In this study, the figure of domestic hardwood was observed using the naked eye and the possibility of substituting imported wood with domestic one in the making woodcraft or furniture was investigated. It was known from the investigation on 8 different hardwoods that there were various figures such as cloud-shaped figure, blister figure, crotch figure, bird's eye figure, etc. in Zelkova serrata wood and the beautiful pigment figure in Diospyros Kaki wood. There were the unusual figures such as wavy grain figure, fiddle back figure, etc. in Cedrela sinensis wood and was clear ray-fleck figure in Quercus variabilis wood. There were also various figures such as wavy grain figure, blister figure, pigment figure, etc. in Sophra japonica, Tilia amurensis, Castanea crenata, Kalopanax septemlobus wood, etc. It is thus that distinguished figures appeared in each kind of wood can be used for craft, sculpture, furniture, and interior material. These kinds of figures can also be used for instrument, toy, stationery, life article material and souvenir, etc. And it can be expected that they will replace the imported wood has been mainly used to make the woodcraft or furniture until now.

• Journal of the Korea Furniture Society
• /
• v.22 no.4
• /
• pp.299-307
• /
• 2011

This article aimed to provide objective and practical information on wood terms of making furniture focusing on the wood species that furniture designers and firms in Korea have used to create furniture from the traditional up to the modern times. Through the content analysis method with wood information from literature related to furniture at home and abroad, studios of making the traditional Korean furniture, domestic furniture firms, and the catalogues of Korean crafts council and Korea furniture society, the wood species of making furniture was studied in the terms showing the number of the species classified in needle leaf tree and broad leaf tree. As a result, the furniture wood terms were analyzed about 230 species including 200 broad leaf tree and 30 needle leaf tree. 74 out of 100 domestic species studied have been used from the traditional up to the modern time for creating the traditional Korean wood furniture. The 230 species were classified by such detailed uses as furniture mainly and the related small objects, interiors, architecture, exteriors, materials like plywood, toys, musical instrument, exercise equipment, household items, and so on. In addition, some of the terms were clarified such as Madika to Jelutong, Karin to Paudauk and Narra, Red sandalwood to Indian rose wood, and Cherry blossoms from home, the same family as Cherry from abroad but the different species, and so on.

• Journal of Forest and Environmental Science
• /
• v.28 no.4
• /
• pp.268-277
• /
• 2012

Among the domestic softwoods, technical value of Pinus koraiensis small diameter logs which have comparatively low applicability was evaluated and sensitive characteristics and physical characteristics were investigated and analyzed for examining if it can be utilized as the interior decoration material. For the sensitive characteristics of Pinus koraiensis, wood figure, wood grain, wood color and odor were evaluated and for the physical characteristics, growth-ring width and latewood percentage, abrasion, density, shrinkage, swelling, absorption, roughness and hardness were evaluated. Then, the possibility to be developed as the interior decoration material was found. As the result of evaluating sensitive characteristics and physical characteristics of domestic Pinus koraiensis, wood figure, wood grain, color and scent clearly were judged to have excellent visual factor as the interior decoration material. And, physical characteristics were also judged to be excellent, so it is judged to be developed as the interior decoration material. Therefore, as the result of various forms of design pattern with domestic Pinus koraiensis small diameter logs, several patterns of interior decoration can be developed by characteristics of each side and colors of heartwood and sapwood. And, in the future, it can be applied to furniture design or interior decoration material for the proper use. Especially, it is considered to contribute to wood applying industry through the study on the quality of domestic small diameter logs which have low applicability.