• Journal of Food Hygiene and Safety
• /
• v.33 no.2
• /
• pp.118-123
• /
• 2018

The objective of this study was to develop a sensitive method for the identification and determination of nitrovin in fishery products by using a solid-phase extraction (SPE), as performed with a liquid chromatography-tandem mass spectrometry (LC-MS/MS). The samples were extracted with a mixture of acetonitrile and water, and were then defatted with acetonitrile saturated hexane, after which further clean-up was accomplished with SPE on the hydrophilic-lipophilic balance (HLB) cartridges. The analytes were subsequently ionized in the positive mode of an electrospray ionization (ESI), and where thereby detected in a process of multiple reaction monitoring (MRM). The linearity (expressed as correlation coefficients) of the matrix calibration curves was > 0.985. The limit of the quantification for the nitrovin was measured at 0.001 mg/kg. The accuracy (expressed as average recovery) was noted between 72.1 and 122%. The precision (expressed as coefficient variation) was noted from 2.9 to 16.9%. According to the CODEX CAC/GL-71 guideline accuracy, precision, linearity, and limit of detection were determined in three matrices (which were flatfish, eel and shrimp). The proposed method was suitable for analyzing the associated nitrovin residues. This application and result can also be a factor to contribute to the non-detection drugs management in fishery products.

• Journal of Food Hygiene and Safety
• /
• v.35 no.2
• /
• pp.109-117
• /
• 2020

This study aimed to develop an analytical method for determination of 18 dyes in livestock and fishery products by liquid chromatograph-tandem mass spectrometry (LC-MS/MS). The developed method was validated for linearity, accuracy, limit of quantifications (LOQ) and recovery based on the CODEX guideline (CAC/GL-71). Target matrices (beef, pork, chicken, egg, milk, flatfish, eel, and shrimp) were extracted using acetonitrile (containing 1% of acetic acid) and then, purified with C₁₈ and primary secondary amine (PSA). Calibration linearity was obtained (r²>0.98) and LOQs were 0.002 mg/kg in animal products. The recoveries of dyes were ranged from 63 to 112% and relative standard deviations (RSDs, %) were less than 15%. The residues of 18 dyes were investigated in real samples (n=124) collected from retail markets in South Korea. As a result, a total of seven samples showed positive results for target analytes in fish samples. However, there was no violation according to the maximum residue limits set by the Korean Food Code. The proposed method will be used for routine analysis of dye residues in livestock and fishery products.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.23 no.10
• /
• pp.1180-1187
• /
• 2012

In this paper, joint transmission space division multiple access(JT-SDMA) scheme is proposed to mitigate inter-cell interference(ICI) in cooperative wireless communications system with limited feedback. We propose a systematic design method for a codebook consisting of a finite number of unitary matrices suitable for network multiple-input multiple-output( MIMO) channel characteristics. A centralized cluster scheduling scheme is proposed to both mitigate ICI and maximizes multiuser diversity gain with limited feedback. It is shown that the proposed JT-SDMA scheme outperforms a existing coordinated SDMA scheme even in wireless network environments where sufficient multiuser diversity order can not be provided through efficient ICI mitigation.

• The Korean Journal of Pesticide Science
• /
• v.15 no.4
• /
• pp.507-528
• /
• 2011

Agricultural workers who mix/loads and spray pesticide in fields expose to pesticide through dermal and inhalation routes. In such situation, exposed amount should be measured quantitatively for reasonable risk assessment. Patch, gloves, socks and mask will be good materials for monitoring for dermal exposure while personal air monitor equipped with solid adsorbent and air pump will be a tool for inhalation exposure. For extrapolation of absorbed amount in dermal exposure matrices and of trapped amount in solid sorbent to total deraml or inhalation exposure, Korean standard body surface area and respiration rate were proposed in substitution of EPA data. Important exposure factors such as clothing and skin penetration ratio of dermal and inhalation exposure were suggested based on Spraying time for exposure monitoring must be long enough that the amount of pesticide to get absorbed/trapped in exposure matrices results in reasonable analytical value. In domestic case for the both of speed sprayer and power spray machine, spraying time of 20~40 minutes (0.1~0.2 ha) will be reasonable per single replicate before extrapolating to 4 hours a day with triplicates experiment.

• Korean Journal of Food Science and Technology
• /
• v.37 no.2
• /
• pp.304-307
• /
• 2005

Multiresidue method was set up for the simultaneous determination of various residual pesticides in potatoes and carrots, which was analyzed by gas chromatography-electron capture detector/nitrogen phosphorus detector. Method consisted with acetone/acetonitrile (9 : 1) extraction and dichloromethane partition, followed by florisil cartridge purification with hexane/dichloromethane/acetonitrile (50 : 45 ; 5) elution. Among 197 pesticides (194 kinds) spiked to food materials, 143 and 155 pesticides were recovered over 70% on potatoes and carrots, respectively. Nineteen pesticides including bromacil, cyproconazole, were not detected in water and sample matrices. Matrix components may affect the low detections of 25 pesticides such as benfuracarb, bitertanol from potatoes and 16 pesticides such as bitertanol, carbosulfan from Carrots. Some pesticides including dichlobenil, fluoroimide and iprodione were highly detected from one or both matrices even though they were not detected from water.

• Journal of the Korean Wood Science and Technology
• /
• v.44 no.3
• /
• pp.406-414
• /
• 2016

The lignin-based carbon nanofiber reinforced epoxy composite has been prepared by immersing carbon nanofiber mat in epoxy resin solution in order to evaluate the physical and mechanical properties. The thermal and mechanical properties of the carbon nanofiber reinforced epoxy composite were analyzed using thermogravimetric analysis (TGA), differential scanning calorimeter (DSC) and tensile tester. It was found that the thermal properties of the carbon nanofiber reinforced epoxy composite improved, with its glass-transition temperature ($T_g$) increased from $90.7^{\circ}C$ ($T_g$ of epoxy resin itself) to $106.9^{\circ}C$. The tensile strengths of carbon nanofiber mats made from both lignin-g-PAN copolymer and PAN were 7.2 MPa and 9.4 MPa, respectively. The resulting tensile strength of lignin-based carbon nanofiber reinforced epoxy composite became 43.0 MPa, the six times higher than that of lignin-based carbon nanofiber mats. The carbon nanofibers were pulled out after the tensile test of the carbon nanofiber reinforced epoxy composite due to high tensile strength (478.8 MPa) of an individual carbon nanofiber itself as well as low interfacial adhesion between fibers and matrices, confirmed by the SEM analysis.

• Applied Chemistry for Engineering
• /
• v.23 no.3
• /
• pp.313-319
• /
• 2012

In this work, the electroplating of copper was introduced on PAN-based carbon fibers for the enhancement of mechanical interfacial strength of carbon fibers-reinforced composites. The surface properties of carbon fibers were determined by scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD), and contact angle measurements. Its mechanical interfacial properties of the composites were studied by interlaminar shear strength (ILSS) and critical stress intensity factor ($K_{IC}$). From the results, it was found that the mechanical interfacial properties of Cu-plated carbon fibers-reinforced composites (Cu-CFRPs) enhanced with increasing the Cu plating time, Cu content and COOH group up to Cu-CFRP-30. However, the mechanical interfacial properties of the Cu-CFRPs decreased dramatically in the excessively Cu-plated CFRPs sample. In conclusion, the presence of Cu particles on carbon fiber surfaces can be a key factor to determine the mechanical interfacial properties of the Cu-CFRPs, but the excessive Cu content can lead the failure due to the interfacial separation between fibers and matrices in this system.

• Tuberculosis and Respiratory Diseases
• /
• v.58 no.4
• /
• pp.367-374
• /
• 2005

Background : The fact that only 10-20% of chronic cigarette smokers develop chronic obstructive pulmonary disease (COPD) reflects the presence of genetic factors associated with the susceptibility to COPD. Recently, it was reported that the surfactant protein A increases the secretion of matrix metalloprotease 9, which degrades extracellular matrices of the lung, through a Toll-like receptor 2 (TLR2). In this context, possible role of TLR2 in the pathogenesis of COPD was postulated, and a functional dinucleotide repeat polymorphism in intron II of TLR2 was evaluated for any association with COPD. Method : Male patients with COPD and male smokers with a normal pulmonary function were enrolled in this study. The number of Guanine-Thymine repeats in intron II of the TLR2 gene were counted. Because the distributions of the repeats were trimodal, the alleles were classified into three subclasses, 12-16 repeats: short (S) alleles; 17-22 repeats: medium length (M) alleles; and 23-27 repeats: long (L) alleles. Result : 125 male patients with COPD and 144 age- and gender-matched blood donors with a normal lung function were enrolled. There were no differences in the distribution of each allele subclass (S, M and L) between the COPD and control group (p=0.75). The frequencies of the genotypes with and without each allele subclass in the COPD and control group were similar. Conclusion : A microsatellite polymorphism in intron II of TLR2 gene was not associated with the development of COPD in Koreans.

• Anatomy and Cell Biology
• /
• v.55 no.2
• /
• pp.229-238
• /
• 2022

Cell migration is an essential process in embryonic development, wound healing, and pathological conditions. Our knowledge of cell migration is often based on the two dimentional evaluation of cell movement, which usually differs from what occurred in vivo. In this study, we investigated cellular migration from blastema tissue toward bovine decellularized mesentery tissue. In this regard, fibronectin (FN) was assessed to confirm cell migration. Therefore, we established a cell migration model using blastema cells migration toward the extracellular matrix derived from bovine mesenteric tissue. A physiochemical decellularization method was utilized based on freeze-thaw cycles and agitation in sodium dodecyl sulfate and Triton X-100 to remove cells from the extracellular matrix (ECM) of bovine mesenteric tissue. These types of matrices were assembled by the rings of blastema tissues originated from the of New Zealand rabbits pinna and cultured in a medium containing FN in different days in vitro, and then they are histologically evaluated, and the expression of the Tenascin C gene is analyzed. By means of tissue staining and after confirmation of the cell removal from mesenteric tissue, polarity, and migration of blastema cells was observed in the interaction site with this matrix. Also, the expression of the Tenascin C gene was assessed on days 15 and 21 following the cell culture process. The results showed that the three dimentional model of cellular migration of blastema cells along with the ECM could be a suitable model for investigating cell behaviors, such as polarity and cell migration in vitro.

• Biomaterials and Biomechanics in Bioengineering
• /
• v.2 no.1
• /
• pp.23-32
• /
• 2015

Facile immobilization of growth factors in hyaluronic acid (HA) hydrogels using dual enzymes is reported in the paper. The hydrogels were formed by using horseradish peroxidase (HRP) and hydrogen peroxide ($H_2O_2$) and transforming growth factor-${\beta}3$ (TGF-${\beta}3$) was covalently conjugated on the hydrogels in situ using tyrosinase (Ty) without any modifications. For the preparation of hydrogels, HA was grafted with poly(ethylene glycol) (PEG), which was modified with a tyrosine. The gelation times of the HA hydrogels were ranging from 415 to 17 s and the storage moduli was dependent on the concentration of $H_2O_2$ and Ty (470-1600 Pa). A native TGF-${\beta}3$ (200 ng/mL) was readily encapsulated in the HA hydrogels and 17% of the TGF-${\beta}3$ was released over 1 month at the Ty concentration of 0.5 KU/mL, while the release was faster when 0.3 KU/mL of Ty was used for the encapsulation (27%). It can be suggested that the growth factors resident in the hydrogels for a long period of time may lead cells proliferating and differentiating, whereas the growth factors that are initially released from the hydrogels can induce the ingrowth of cells into the matrices. Therefore, the dual enzymatic methods as facile gel forming and loading of various native growth factors or therapeutic proteins could be highly promising for tissue regenerative medicines.