• Journal of Drive and Control
• /
• v.14 no.2
• /
• pp.1-8
• /
• 2017

The spool displacement of a directional control valve can be considered as the standard signal for the measurement of its bandwidth frequency. When the spool displacement is not available, the metering-orifice system is suggested in this study as an alternative way to measure the - 3 dB amplitude-ratio bandwidth frequency of the hydraulic directional-control valve. The amplitude ratio of the metering-orifice pressure can be adjusted to equal that of the spool displacement through the controlling of the metering-orifice opening area. A series of experiments were conducted to verify the effectiveness of the metering-orifice system. The metering orifice was confirmed as adequate for the measurement of the - 3 dB amplitude-ratio bandwidth frequency.

• Journal of Drive and Control
• /
• v.18 no.2
• /
• pp.9-19
• /
• 2021

The spool displacement signal of a directional control valve, including the servo valve, can be considered as the standard signal to measure dynamic characteristics. When the spool displacement signal is not available, the velocity signal of a metering cylinder piston can be used. In this study, the frequency response characteristics of the metering cylinder are investigated for the spool displacement input. The transfer functions of the servo valve-metering system are derived taking into consideration the oil inertia effect in the transmission lines. The theoretical results of the transfer functions are verified through computer simulations and experiments. The oil inertia effect in the transmission lines was found to have a very significant effect on the bandwidth frequency of the servo valve-metering cylinder system. In order to more precisely measure the dynamic characteristics of a servo valve, the metering cylinder should be set up to minimize the oil inertia effect by increasing the inner diameters of the transmission lines or shortening their lengths.

• Journal of the Korean Society for Precision Engineering
• /
• v.24 no.9
• /
• pp.60-67
• /
• 2007

A signal conditioning circuit for capacitive displacement sensors was developed using a high frequency modulation/demodulation method, and its performance was evaluated. Since capacitive displacement sensors can achieve high resolution and linearity, they have been widely used as precision sensors within the range of several hundred micrometers. However, they inherently have a limitation in low frequency range and some nonlinearity characteristics and so a specially designed signal conditioning circuit is needed to handle these properties. The developed signal processing circuit consists of three parts: linearization, modulation/demodulation, and nonlinearity compensation. Each part was constructed discretely using several IC chips and passive elements. An evaluation system for precision displacement sensors was developed using a laser interferometer, a precision stage, and a PID position controller. The signal processing circuit was tested using the evaluation system in the respect of resolution, repeatability, linearity, and so on. From the experimental results, we know that a highly linear voltage output can be obtained successfully, which is proportional to displacement and the nonlinearity of output is less than 0.02% of full range. However, in the future, further investigation is required to reduce noise level and phase delay due to a low-pass filter. The evaluation system also can be applied effectively to calibration and evaluation of precision sensors and stages.

• Imaging Science in Dentistry
• /
• v.36 no.1
• /
• pp.17-24
• /
• 2006

Purpose : The objective of this study was to investigate the effect of TMJ disc displacement on the TMJ disc configuration and surrounding osseous structure. Materials and Methods : The proton density and 72-weighted MR images of 57 TMJs were retrospectively studied. These TMJs were divided into three groups according to the anterior disc displacement status on MR sagittal images, those were the normal, anterior disc displacement with reduction (ADWR), anterior disc displacement without reduction (ADWOR). The frequency of disc configuration and surrounding bony change, the border status between articular disc and retrodiscal tissue were investigated according to the positional change of articular disc. Results : There were significant statistical differences of chi-square statistics of TMJ disc configurational type between normal and ADWR/ADWOR group, respectively. Surrounding bony change frequently appeared in ADWOR and a statistically significant difference of chi-square statistics of bony change frequency between normal and ADWOR group was observed. Conclusion : These results suggested that the disc configuration and bony change of TMJ are strongly related to TMJ disc displacement.

• Journal of Korean Association for Spatial Structures
• /
• v.16 no.3
• /
• pp.99-106
• /
• 2016

The proposed hybrid damper installs at a coupling beam and consists of a high-damping rubber (HDR) and steel pin. The proposed hybrid damper adopted a pin-lock system acts as a viscoelastic damper under wind load (small displacement) while it behaves as a hysteretic damper under earthquake load (large displacement). In this paper, the pin-lock mechanism and structural performance of the proposed hybrid damper is evaluated through experiment. Experiments were carried out with the variables which displacement, loading frequency and steel pin quantities were used. Test results showed that the pin-lock mechanism and the performance of the hybrid damper under a large displacement were verified. Also equivalent damping ratios of HDR were increasing at a small displacement as displacement amplitudes were increasing. However HDR did not depend on frequency.

• Proceedings of the KIEE Conference
• /
• 1998.11c
• /
• pp.844-846
• /
• 1998

In this study, Brass endcap with 2, 3, 5, and 7mm contact surface and 0.6, 0.9, 1.2, 1.5mm conical cavity depths was fabricated by the punch die while keeping the cavity diameter constant 9.25mm then displacement characteristics of the cymbal actuators with each of brass endcap thickness were measured under an applied voltage $60V_{max}$. Dispacement increased with increasing contact surface and resonant frequency decreased with increasing contact surface, cymbal actuator with 7mm contact surface and 1.5mm endcap cavity depth exhibits $35.89{\mu}m$ displacement and 18.8kHz resonant frequency, displacement increased with increasing endcap cavity depth while contact surface was kept constant at 3mm and Below a endcap thickness of 0.2mm, Differences in displacement between 1.2mm and 1.5mm cavity depth appeared at $0.18{\mu}m$. that is, displacement of cymbal actuator with 1.2mm over cavity depth saturated nearly.

• Smart Structures and Systems
• /
• v.16 no.3
• /
• pp.521-535
• /
• 2015

Vibration-based monitoring is one approach used to perform structural condition assessment. By measuring structural response, such as displacement, dynamic characteristics of a structure may be estimated. Often, the primary dynamic responses in civil structures are below 5 Hz, making accurate low frequency measurement critical for successful dynamic characterization. In addition, static deflection measurements are useful for structural capacity and load rating assessments. This paper presents a DC coupled continuous wave radar to accurately detect both dynamic and static displacement. This low-cost radar sensor provides displacement measurements within a compact, wireless unit appropriate for a range of structural monitoring applications. The hardware components and operating mechanism of the radar are introduced and a series of laboratory experiments are presented to assess the performance characteristics of the radar. The laboratory and field experiments investigate the effect of factors such as target distance, motion amplitude, and motion frequency on the radar's measurement accuracy. The results demonstrate that the radar is capable of both static and dynamic displacement measurements with sub-millimeter accuracy, making it a promising technology for structural health monitoring.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2004.04a
• /
• pp.25-32
• /
• 2004

In this proposed work new finite element model for multi-delaminated plates is proposed. In the current analysis procedures of multi-delaminated plates, plate element based on Mindlin plate theory is used in order to obtain accurate results of out-of-plane displacement of thick plate. And for delaminated region, plate element based on Kirchhoff plate theory is considered. To satisfy the displacement continuity conditions, displacement vector based on Kirchhoff theory is transformed to displacement of transition element. The numerical results show that the effect of delaminations on the modal parameters of delaminated composites plates is dependent not only on the size, the location and the number of the delaminations but also on the mode number and boundary conditions. Kirchhoff based model have higher natural frequency than Mindlin based model and natural frequency of the presented model is closed to Mindlin based model.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07b
• /
• pp.693-696
• /
• 2003

Piezoelectric ceramics were made by a doctor blade methode and piezoelectric fans were fabricated by sandwiched a slim and long metal between two layers of ceramics. A maximum displacement of piezoelectric fan occurs in the resonance frequency of a long metal and the resonance frequency of them is in inverse proportion to the square of a length of metal. The piezoelectric fan made from a wide and thin piezoelectric ceramics($13{\times}0.2{\times}30mm^3$) showed a maximum displacement in all samples, and the maximum displacement was about 20mm in a commercial power (200V, 60Hz of sine wave).

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.772-775
• /
• 2003

A bushing is a device used in automotive suspension systems to reduce the load transmitted from the wheel to the frame of the vehicle. A bushing is a hollow cylinder, which is bonded to a solid steel shaft at its inner surface and a steel sleeve at its outer surface. The relation between the force applied to the shaft and the relative deformation of a bushing is nonlinear and exhibits features of viscoelasticity. A force-displacement relation for bushings is important for multibody dynamics numerical simulations. For the nonlinear viscoelastic axial response, Pipkin-Rogers model, the direct relation of force and displacement, has been derived from Lianis model and the sinusoidal input was used for Pipkin-Rogers model, and the affection of displacement with frequency change was studied with Pipkin-Rogers model.