• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2006년도 추계 학술발표회 논문집
• /
• pp.837-840
• /
• 2006

This paper presents the experimental results on the development length of FRP tendons by direct pullout test. Two types of FRP tendons, namely, CFCC tendon and KICT tendon, and PS tendon were investigated. The development length defined as the minimum embedment length required to develop the ultimate tensile strength was suggested using the test results. It was found that the development length from the direct pullout test was greater than those of various standards. This may result from the fact that the wedge effect does not exist because there is no prestressing force in the direct pullout test. Further study and experiment are necessary to derive the reasonable development length for FRP tendon.

• 한국강구조학회 논문집
• /
• 제15권2호
• /
• pp.137-145
• /
• 2003

본 연구에서는 국산 PS 강봉의 직경, 반복최소응력 및 반복최대응력 등을 실험변수로 하여 직접 인장 피로실험을 수행하였다. 정적 인장실험 결과, 국산 PS 강봉의 응력 - 변형률 곡선과 극한강도 등을 얻었다. 또한, 피로실험에서의 특징적인 실험결과는 PS 강봉의 직경은 피로 수명에 중요한 인자가 아니며, 반복 최소응력의 크기는 국산 PS 강봉의 피로수명에 매우 큰 영향을 미치는 것으로 나타났다. 이러한 피로실험결과를 통계 분석하여 PS 강봉의 응력 범위 및 반복 최소응력 등을 변수로 하는 피로강도 예측식을 제안하였다. 피로실험 중, 시편중앙에 설치한 Extensometer를 이용하여, 변형률의 변화를 측정하였으며, 측정된 변형률 변화현상에서 탄성계수의 변화현상을 구하였다. 변형률 증가현상은 3단계의 형태 즉, 초기에 급격한 증가 후 서서히 증가하며 파괴 직전에 급격하게 증가하는 형태로 나타났다. 탄성계수의 변화현상은 변형률 변화현상과 유사하게 감소하는 것으로 나타났으며 응력수준은 탄성계수 변화에 큰 영향을 주지 않는 것으로 나타났다.

• 대한치과교정학회지
• /
• 제20권2호
• /
• pp.283-291
• /
• 1990

The purpose of this study was to measure and compare tensile and shear strength for 4 types of new direct-bonding brackets and same brackets after recycling and to evaluate the change of bracket slot width after recycling. Four types of new direct-bond brackets were bonded to recently extracted human premolar teeth and the tensile and shear strength was measured by Universal Testing Machine. The brackets were recycled by chemical process and the tensile and shear test was repeated. To evaluate the change of the bracket slot width, slot width was measured by the Topcon Universal Measuring Microscope before and after recycling. Following results were obtained: 1. There was no satistically significant difference between the tensile and shear strength of recycled brackets and those of new brackets. 2. In both new and recycled brackets, the tensile and shear strength of perforated base bracket was lower than those of photoetched, foilmesh and contou-lok mesh base brackets. (P<0.01) 3. There was no statistically significant difference in bonding strengths of control group bonded only once and two times. 4. There was no statistically significant difference in the change of the bracket slow width after recycling process. 5. Of the failure, the combination type (58%) in the tensile strength and the tooth adhesive interface (65%) in the shear strength was the most common type.

• 대한치과교정학회지
• /
• 제15권2호
• /
• pp.261-269
• /
• 1985

The purpose of this study was to measure and compare tensile strength for 3 types of new direct-bond brackets and the same brackets after recycling and to evaluate recycled brackets to determine the extent of physical alteration after recycling. Three types of new direct-bond brackets were bonded to recently extracted human premolar teeth and the tensile strength was measured by Universal Testing Machine. The brackets were recycled by thermal process and the tensile test was repeated. To determine the extent of physical alteration after recycling, the slot width and the hardness of metal brackets were measured and to analyze the microstructure of the brackets, photographs of the bracket microstructure were taken. Following results were obtained: 1. The tensile strength of recycled brackets was lower than that of new brackets, but there was no statistically significant difference. (p>0.05) 2. In the new and recycled brackets, the tensile strength of mini-mesh base bracket was statistically higher than that of conturlok base bracket, $(p\leq0.05)$ but there was no statistically significant difference between production of other companies. (p>0.05) 3. The slot width of metal bracket was enlarged from 0.459mm to 0.469mm as a result of the recycling process. (p>0.005) 4. As temperature was increased in thermal treatment, the grains of bracket metal gradually became coarser and the hardness was decreased.

• 대한건축학회논문집:구조계
• /
• 제35권3호
• /
• pp.27-33
• /
• 2019

The purpose of this study is to provide and evaluate the tensile properties of masonry element such as tensile strength, strain, modulus of elasticity and stress-strain relationship through the direct tension test with varies of mortar strength. From the experiment, the tension fracture was observed along the interfaces between the brick and the mortar. Tension properties of masonry element was significantly affected by compressive strength of mortar, $f_m$, indicating that higher tensile strength and modulus of elasticity of masonry element were obtained with increase of $f_m$. The strain of a masonry element was inversely proportional to $f_m$ due to the lower ductility of a higher mortar strength. A tensile stress-strain relationship of masonry element was generalized based on the numerical analysis and the regression analysis using test data. The proposed model shows fairly good agreement with the test measurements.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2002년도 Proceedings of the International Welding/Joining Conference-Korea
• /
• pp.89-93
• /
• 2002

A study of noticeable improvement in welding speed in thin-plate Type 304 stainless steels gas tungsten arc (GTA) welding was investigated. The welding speeds were increased to more than 3m/min, up to 8m/min. During the welding, Direct Current Straight Polarity (DCSP) and pulsed current GTA welding processes were carried out, respectively. The appropriate high speed welding parameters were established while achieving a high quality weld. After this, Erichsen test and tensile test were performed. The results obtained wert summarized as following: ultra high speed welding for thin-plate Type 304 could be satisfactorily welded with high speed from 3m/min to 8m/min in both DCSP and pulsed GTA welding; Increasing welding speed was found to decrease the ductility, tensile strength md elongation of welded joint; The optimal frequency would be 200Hz-500Hz for high speed welding in pulsed current welding; DCSP welding could obtain the better results of Erichsen test and tensile test than those of pulsed current welding obtained.

• 한국건설순환자원학회논문집
• /
• 제8권4호
• /
• pp.458-466
• /
• 2020

이 연구의 목적은 비정질 강섬유와 폴리아미드 섬유를 이용한 고성능 하이브리드 섬유보강 콘크리트의 압축 및 인장 거동을 평가하는 것이다. 이를 위하여 목표 압축강도 40MPa 및 60MPa 각각에 대해서 비정질 강섬유와 폴리아미드 섬유를 총 부피비로 1.0% 혼입한 고성능 하이브리드 섬유보강 콘크리트를 제작한 후 압축강도, 압축인성, 직접인장강도 및 응력-변형률 특징 등의 압축 및 인장 거동을 평가하였다. 그 결과, 고성능 하이브리드 섬유보강 콘크리트의 압축강도는 플레인 콘크리크보다 다소 감소하였으나, 압축인성, 압축인성 비, 직접인장강도는 크게 증가하는 것으로 나타났다. 또한 압축 및 인장 시험시 플레인 콘크리트는 최대응력 이후 취성파괴를 나타냈으나, HPHFRC는 변형연화 현상을 나타내어, 압축 및 인장 거동이 크게 개선되는 것으로 나타났다.

• Structural Engineering and Mechanics
• /
• 제81권2호
• /
• pp.243-258
• /
• 2022

In this paper, tensile behavior of joint filling has been investigated under experimental test and numerical simulation (particle flow code). Two concrete slabs containing semi cylinder hole were prepared. These slabs were attached to each other by glue and one cubic specimen with dimension of 19 cm×15 cm×6 cm was prepared. This sample placed in the universal testing machine where the direct tensile stress can be applied to this specimen by implementing a special type of load transferring device which converts the applied compressive load to that of the tensile during the test. In the present work, two different joint filling thickness i.e., 3 mm and 6 mm were prepared and tested in the laboratory to measure their direct tensile strengths. Concurrent with experimental test, numerical simulation was performed to investigate the effect of hole diameter, length of edge notch, filling thickness and filling length on the tensile behavior of joint filling. Model dimension was 19 cm×15 cm. hole diameter was change in four different values of 2.5 cm, 5 cm, 7.5 cm and 10 cm. glue lengths were different based on the hole diameter, i.e., 12.5 cm for hole diameter of 2.5 cm, 10 cm for hole diameter of 5 cm, 7.5 cm for hole diameter of 7.5 cm and 5 cm for hole diameter of 10 cm. length of edge notch were changed in three different value i.e., 10%, 30% and 50% of glue length. Filling thickness were changed in three different value of 3 mm, 6 mm and 9 mm. Tensile strengths of glue and concrete were 2.37 MPa and 6.4 MPa, respectively. The load was applied at a constant rate of 1 kg/s. Results shows that hole diameter, length of edge notch, filling thickness and filling length have important effect on the tensile behavior of joint filling. In fixed glue thinks and fixed joint length, the tensile strength was decreased by increasing the hole diameter. Comparing the results showed that the strength, failure mechanism and fracture patterns obtained numerically and experimentally were similar for both cases.

• 한국지반공학회논문집
• /
• 제31권3호
• /
• pp.5-16
• /
• 2015

본 연구에서는 토사 또는 암반 틈새에 주입하는 그라우팅(시멘트 페이스트)에 섬유를 혼합할 경우 발생하는 인장강도의 특성을 연구하였다. 이와 같이 시멘트로 고결된 토목재료의 인장강도 평가에는 간접적인 방법으로 인장강도를 평가하는 쪼갬인장시험을 주로 사용하고 있다. 하지만, 본 연구에서는 강섬유 또는 PVA 섬유를 중량비로 0%, 0.5%, 또는 1% 혼합한 시멘트 페이스트 내에 유압 실린더를 내장한 직경 15cm, 높이 30cm의 공시체를 제작한 다음 공시체 내부에서 직접 인장력을 가하는 직접인장시험법을 개발하였다. 또한 동일한 재료로 직경 5cm, 높이 10cm 공시체를 만들어 쪼갬인장시험을 실시하여 인장강도 시험방법에 따른 시멘트 페이스트의 인장강도를 비교, 평가하였다. 각각의 공시체는 대기 중에서 7일 또는 28일 양생한 다음 인장시험을 실시하였다. 시험방법에 따른 인장강도는 내장형 실린더를 이용한 직접인장시험법이 쪼갬인장시험법 보다 96%-290% 정도 높은 값을 보였다. 한편 두 종류의 인장시험법에 대한 3차원 유한요소해석을 실시하였으며, 실험 결과와 유사하게 내장형 실린더 인장시험법이 3배 정도 높은 인장강도를 보였다. 섬유 혼합량이 1%까지 증가함에 따라 인장강도는 시험방법에 관계없이 7일 양생한 공시체는 119%-190%, 28일 양생한 공시체는 23%-131%까지 증가하였으며, 양생일수가 7일에서 28일로 증가함에 따라 인장강도는 대부분 감소하는 경향을 보였다. 대부분의 경우 강섬유가 포함된 경우보다 PVA 섬유가 포함된 경우에 약 14%-38% 정도 높은 인장강도를 보였다.

• 한국지반공학회논문집
• /
• 제19권6호
• /
• pp.285-298
• /
• 2003

본 연구에서는 경사판 시험기를 이용하여 매립지에 흔히 나타나는 토목섬유/토목섬유, 토목섬유/모래의 접촉 마찰특성을 평가하였다. 경사판 시험기는 연직응력이 낮은 상태에서의 전단 거동을 정확히 모사하는 시험기로 널리 알려져 있으며, 본 연구에서는 이 시험기를 이용하여 각 접촉면의 마찰각을 평가하는 동시에, 각 토목섬유에 유발되는 인장력도 측정하였다. 실험 결과, 연직응력의 크기, 토목섬유의 종류, 토목섬유의 흙의 구성에 따라 접촉면의 마찰각과 토목섬유에 유발되는 인장력이 각각 다르게 측정됨을 확인하였다. 한편, 본 연구에서는 모래/지오텍스타일/지오멤브레인, 즉 두개의 접촉면을 동시에 모사하는 실험을 실시하여, 지오멤브레인 상부에 위치하는 지오텍스타일로 인해 지오멤브레인에 유발되는 인장력이 감소함을 관찰하였다. 본 연구 결과는 동일한 접촉면을 대상으로 실시된 직접전단 시험 결과와 비교하였으며, 마지막으로 상자의 변위가 발생하기 시작하는 시점, 즉 각 접촉면의 한계 경사에서 토목섬유에 유발되는 인장력을 기존에 제안된 해석해와 비교하여, 해석해의 정확도와 설계시 적용 가능성에 대하여 고찰하였다.