• 한국식품과학회지
• /
• 제17권5호
• /
• pp.406-408
• /
• 1985

본 연구에서는 현미취반시 생성되는 고휘발성 향기성분중 고미취의 주성분인 n-hexanal의 가스크로마토그래피에 의한 분리및 정량방법을 개선하였다. 개발된 가스크로마토그래피의 운전조건하에서 n-hexanal의 분리를 시도한 결과, n-hexanal은 다른 고휘발성 향기성분으로부터 완전히 분리가 되었고, 특히 n-hexanal의 머무름시간(retention time)은 3.5분으로 아주 빨리 분리가 되었다. 그리고 Direct vapor injection 방법에 따른 n-hexanal의 정량시 각 시료의 n-hexanal 값은 10%이내의 오차를 보여주어, 고휘발성 향기성분중 n-hexanal의 정량분석이 가능하였다.

• 한국자동차공학회논문집
• /
• 제12권1호
• /
• pp.32-38
• /
• 2004

To evaluate the durability of direct injection diesel engine using biodiesel fuel, a small D. I. diesel engine was operated on a blend(BDF 20) of 20％ biodiesel fuel and 80％ diesel fuel for 200 hours. Engine dynamometer test was performed at a load of 90％ and a speed of 1900 rpm to monitor the engine performance and exhaust emissions. Engine performance parameters and exhaust emissions were sampled at 1 hour interval for analysis. The combustion maximum pressure and the crank angle at this maximum pressure as a combustion variation factor were considered to study the combustion characteristics of BDF 20 in diesel engine during durability test. As the results, the standard deviations and errors of combustion variation factors on BDF 20 were very little and combustion characteristics were very stable during the durability test. BDF 20 resulted in lower emissions of carbon monoxide, carbon dioxide, and smoke emissions with special increase of nitrogen oxides compared to diesel fuel. There was no also unusual change in engine oil composition from using BDF 20. Most of engine parts were clean and showed little wear, but soots were detected around the hole of fuel injector when BDF 20 was used in direct injection diesel engine for 200 hours.

• 한국산업융합학회 논문집
• /
• 제26권4_2호
• /
• pp.649-656
• /
• 2023

Recently, global warming has become severe, and regulation is established for carbon savings each field. its regulation is applied to various fields using IC engine such as automobile, ship, agricultural machine. Therefore engine block applied Common Rail Direct Injection(CRDI) technology, that carry out thermal-structure analysis to examine design. The thermal load about 900℃ by explosion was applied in cylinder. And pressure about 9 MPa(90 Bar) was applied to structure analysis. As a result, it was the highest at 185.99℃ at the top of cylinder. Static-structure analysis applied thermal load, that was shown maximum equivalent stress at 142.59 Mpa and Maximum principal stress 145.03 MPa, Minimum principal stress -149 MPa. When compare analysis results to material property, it design is safety structurally.

• 한국분무공학회지
• /
• 제28권4호
• /
• pp.169-175
• /
• 2023

Multi-injection scheme is being applied to GDI combustion to reduce PM and PN emission to meet the EU7 regulation. However, very short injection duration encounters the ballistic injection region, which injection quantity does not increase linearly with injection duration when applying multi-injection. In this study, numerical studies were conducted to reveal the cause of ballistic injection and the effect of design parameters on ballistic region using 1-D simulation, AMESim. Injection rate and injection quantity were compared with experiment to validate the established model, which showed the accuracy with 10% error. The model revealed that the tendency of ballistic region coincides with the needle motion behavior, which means that parameters at the upper part of needle such as electro-magnetic force, needle spring force and needle friction force have dominant effect on ballistic injection. To figure out the effect of electro-magnetic and needle friction force on ballistic, those parameters were varied to plus and minus 10% with model. The result showed that those parameters clearly changed the ballistic region characteristics, however, the impact became insignificant for outside of ballistic region, which means that the ballistic injection is mainly influenced by initial motion of injector needle.

• Nuclear Engineering and Technology
• /
• 제34권5호
• /
• pp.421-432
• /
• 2002

As one of the advanced design features of the APR1400, direct vessel injection (DVI) system is being considered instead of conventional cold leg injection (CLI) system. It is known that the DVI system greatly enhances the reliability of the emergency core cooling (ECC) system. However, there is still a dispute on its performance in terms of water delivery to the reactor core during the reflood phase of a large-break loss-of-coolant accident (LOCA). Thus, experimental validation is under progress. In this paper, test results of direct ECC bypass performed in the steam-water test facility tailed MIDAS (Multi-dimensional Investigation in Downcomer Annulus Simulation) are presented. The test condition is determined, based on the preliminary analysis of TRAC code, by applying the ‘modified linear scaling method’with the l/4.93 length scale . From the tests, ECC direct bypass fraction, steam condensation rate and information on the flow distribution in the upper annulus downcomer region are obtained.

• 대한기계학회논문집B
• /
• 제26권7호
• /
• pp.1047-1054
• /
• 2002

To improve the fuel consumption and exhaust emission for gasoline engines, GDI(Gasoline Direct Injection) system was spotlighted to solve above requirements. Thus, many researchers have been studied to investigate the spray characteristics and the mixture formation of GDI injector. In this study, we tried to study the spray characteristics of a gasoline direct injector by using entropy analysis and PlV methods. The entropy analysis is based on the concept of statistical entropy, and it identifies the degree of homogeneity in the fuel concentration. The PlV method was adopted to determine the fluid dynamics information at the spray. From the applied results on a direct injection gasoline spray, we could find that the direct diffusion phenomena was a dominant factor in the formation of a homogeneous mixture at downstream of GDI spray especially under vaporizing ambient conditions, and mixing phenomena was also progressed by momentum exchange with induced air. In addition, the correlation between entropy and vorticity strength enabled to find their relation.

• 한국자동차공학회논문집
• /
• 제22권4호
• /
• pp.55-64
• /
• 2014

This work was investigated on pilot injection strategy of blended fuels(Diesel-DME) for combustion and emissions in a single cylinder direct injection compression ignition engine. Diesel and DME were blended by the method of weight ratio. Weight ratios for diesel and DME were 95:05 and 90:10 respectively. dSOI between main and pilot injection timing was varied. A total amount of injected fuels(single injection) was adjusted to obtain the fixed BMEP as 4.2 bar in order to compare with the fuel conditions. Also, the amount of pilot injection fuel was varied by 5%, 10% and 20% of total injection fuel. The engine was equipped with common rail and injection pressure is 700 bar at 1200 rpm. As a result, when mixing ratio increase, indicated thermal efficiency was increased in comparison with DD 100 and CO, THC and smoke were lower than DD 100. The influence of reducing NOx by pilot injection was more effective than DD 100. When pilot injection quantity increase, abrupt increase of NOx was occured at pilot injection quantity of 20%.

• Journal of electromagnetic engineering and science
• /
• 제8권3호
• /
• pp.134-137
• /
• 2008

This paper proposes a novel quadrature VCO(QVCO) based on direct back-gate second harmonic coupling. The QVCO directly couples the current sources of the conventional LC VCOs through the back-gate instead of front-gate to generate quadrature signals. By the second harmonic injection locking, the two LC VCOs can generate quadrature signals without using on-chip transformer, or stability problem that is inherent in the direct front-gate second harmonic coupling. The proposed QVCO is implemented in $0.18{\mu}m$ CMOS technology operating at 2 GHz with 5.0 mA core current consumption from 1.8 V power supply. The measured phase noise of the proposed QVCO is - 63 dBc/Hz at 10 kHz offset, -95 dBc/Hz at 100 kHz offset, and -116 dBc/Hz at 1 MHz offset from the 2 GHz output frequency, respectively. The calculated figure of merit(FOM) is about -174 dBc/Hz at 1 MHz offset. The measured image band rejection is 46 dB which corresponds to the phase error of $0.6^{\circ}$.

• 한국분무공학회지
• /
• 제6권4호
• /
• pp.39-48
• /
• 2001

The Gasoline Direct Injection(GDI) system has been highlighted due to the improvement of fuel consumption and the control of exhaust emission from gasoline engines. Main purpose of the present study is to measure spray characteristics of GDSI for real engine application. We have investigated experimentally spray tip penetration, spray angle, tip velocity and spatial spray distribution. Counter-rotating vortex grown on the spray surface plays an important role in the spray characteristics. Accordingly the spray tip penetration and tip velocity do not excess 50mm, 20m/s respectively, under 0.6MPa ambient pressure. the spray cone angle of GDSI have a same tendency to a simplex swirl atomizer.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1993년도 정기총회 및 추계학술대회 논문집 학회본부
• /
• pp.103-105
• /
• 1993

This paper proposed a new direct vector control scheme using high frequency current injection. This scheme has some attractive features such as using no flux sensor or speed sensor, robustness of parameter variation, capability of accurate vector control at very low speed. Compared to other direct vector control scheme, this scheme doesn't depends on phase delay and difference of magnitude of estimated flux, rotor resistance and all inductances except stator resistance. These features are proved by computer simulation and experimental results.